1. Agarose gel Electrophoresis
Ameer Effat M. Elfarash
Dept. of Genetics
Fac. of Agriculture, Assiut Univ.

2. قياس تركيز الـ DNA فى العينات:
Spectrophotometers
Agarose gel Electrophoresis

3. Spectrophotometers
quantity
quality

4. DNA absorbs UV light at 260 &280 nm & aromatic proteins absorb UV light at 280 nm
A pure sample of DNA has the 260/280 ratio at 1.8 & is relatively free from protein contamination.

5. NanoDrop spectrophotometer
Check samples on a Nanodrop first to measure:
Purity
Concentration
Can accurately measure tiny volumes of sample as low as 1 μl.

6. Agarose gel Electrophoresis

7. Electrophoresis of DNA
Gel
DNA Size

8. Analyzing DNA Samples in a Research Lab
If properly done, genomic extraction should result in bright bands in the very high base pair range of a gel electrophoresis.

9. Agarose Gel Electrophoresis
Agarose gel electrophoresis is
routinely used for DNA analysis.
Separate DNA by Molecular size (bp.)
Smaller molecules move faster
than large molecules
small
large + -
Power

10. Agarose Gel Preparation
Buffer
Power supply
Cover
Gel tank
Electrical leads 
Casting tray
Agarose
Gel combs
Flask for boiling 10

11. Agarose Buffer Solution
Combine the agarose powder and buffer solution. Use a flask that is several times larger than the volume of buffer. 11

12. Melting the Agarose Agarose is insoluble at room temperature (left).
The agarose solution is boiled until clear (right). 12

13. Pouring the gel
Allow the agarose solution to cool slightly (~60ºC) and then carefully pour
the melted agarose solution into the casting tray.
Avoid air bubbles. 13

14. When cooled, the agarose polymerizes, forming a flexible gel.
It should appear lighter in color when completely cooled (30-45 minutes)
Carefully remove the combs and tape. 14

15. Place the gel in the electrophoresis chamber.15

16. DNA buffer   wells    Anode (positive) Cathode (negative)
Add enough electrophoresis buffer to cover the gel to a depth of at least 1 mm. Make sure each well is filled with buffer. 16

17. Sample Preparation for Loading
Mix the samples of DNA with the 6X sample loading buffer (w/ tracking dye). This allows the samples to be seen when loading onto the gel, and increases the density of the samples, causing them to sink into the gel wells.
6X Loading Buffer: 
 Bromophenol Blue (for color and marker)
 Glycerol (for weight) 17

18. Loading the Gel
Carefully place the pipette tip over a well and gently expel the sample. The sample should sink into the well. Be careful not to puncture the gel with the pipette tip. 18

19. Running the Gel Voltage (75, 100, 150 ……)
Place the cover on the electrophoresis chamber,
Connect the electrical leads to the power supply.
DNA migrates toward the anode (red).
When the power is turned on, bubbles should form on the
electrodes in the electrophoresis chamber. 19

20. Cathode (-)  wells  Bromophenol Blue Gel Anode (+) DNA (-) 
After the current is applied, make sure the Gel is running in the correct direction. Bromophenol blue will run in the same direction as the DNA. 20

21. Staining the Gel
• Ethidium bromide binds to DNA and fluoresces under UV light,
allowing the visualization of DNA on a Gel.
• Ethidium bromide can be added to the gel and/or running buffer
before the gel is run or the gel can be stained after it has run.
***CAUTION! Ethidium bromide is a powerful mutagen and is moderately toxic. Gloves should be worn at all times. 21

22. Staining the Gel
• Place the gel in the staining tray containing warm diluted stain.
• Allow the gel to stain for minutes.
• To remove excess stain, allow the gel to destain in water.
• Replace water several times for efficient destain. 22

23. Ethidium Bromide requires an UV light to visualize23