1. How to configure Stand Alone Camera Control
Stand Alone Camera Control

2. This presentation is intended to guide the installer step by step through camera control installation.
Stand Alone Camera Control

3. Standalone DCN system with Camera Control
Direct Camera Control
With Allegiant Video Switcher
Stand Alone Camera Control

4. Direct Camera Control (Stand Alone)
Requirements :
One Dome Camera
One Monitor
CCU with TCB4
DCN software V9.30 or higher!!!
Temporary installation PC
Software LBB3562 V2.0 or higher!!!
Stand Alone Camera Control

5. Step 1 Connect PC and Monitor to Dome Camera
AutoDome
Camera
RS232
Temporary PC
with one Comport
Make sure that the Dome camera has an address.
Stand Alone Camera Control

6. Step 2 Install virtual keyboard software LTC 5138/00
Program
AutoDome
Camera
RS232
Temporary PC
with one Comport
Stand Alone Camera Control

7. Step 3 Configure Virtual Keyboard
Stand Alone Camera Control

8. Stand Alone Camera Control
Stand Alone Camera Control

9. Make sure you choose the right camera!!
Stand Alone Camera Control

10. Keep in mind !! Camera nr = Camera Address Stand Alone Camera Control
Stand Alone Camera Control

11. Stand Alone Camera Control
Stand Alone Camera Control

12. Stand Alone Camera Control
Stand Alone Camera Control

13. Step 4 Set Pre-Positions
Stand Alone Camera Control

14. Stand Alone Camera Control
Stand Alone Camera Control

15. Repeat Step 4 to set all Pre-Positions
Set the highest Pre-Position as overview
Stand Alone Camera Control

16. Step 5 Check the Pre-Positions
Stand Alone Camera Control

17. First make sure that the pre-positions are set.
If you were not successful setting up the pre-positions please don’t continue with the next steps.
First make sure that the pre-positions are set.
Stand Alone Camera Control

18. Step 6 Connect CCU to PC DCN CCU LBB 3500/x5 RS232 Temporary PC
with one Comport
Baudrate 9.6K
Stand Alone Camera Control

19. Step 7 Change baudrate of CCU
Now you have to change the baudrate of Port 1(on the CCU) to 9.6K!!
Port 1 Protocol = Camera Control Baudrate = 9.6K
Stand Alone Camera Control

20. If you are using the LBB3500/15 or /35 make sure you connect the RS232 cable to Port 2.
Stand Alone Camera Control

21. Step 8 Install Camera Control Software LBB3562
DCN CCU
Camera
Control
Program
Temporary PC
with one Comport
LBB 3500/x5
RS232
Baudrate 9.6K
Stand Alone Camera Control

22. Make sure you choose the configuration without Allegiant Video Switcher
Stand Alone Camera Control

23. Step 9 Start Camera Installation software
Stand Alone Camera Control

24. Step 10 Combine seat numbers with camera pre positions
Stand Alone Camera Control

25. Keep in mind !!
Make sure you choose the right camera!! Camera nr = Camera Address
Stand Alone Camera Control

26. Stand Alone Camera Control
Stand Alone Camera Control

27. 5
Stand Alone Camera Control

28. Step 11 Connect CCU to AutoDome Camera
RS232
DCN CCU
Baudrate 9.6K
Baudrate 9.6K
Stand Alone Camera Control

29. End of Installation
© Robert Bosch GmbH reserves all rights even in the event of industrial
property rights. We reserve all rights of disposal such as copying and passing on to third parties.
Stand Alone Camera Control

30. With use of Allegiant Video Switcher
Requirements :
Allegiant switcher
Video Switcher keyboard
Fixed and /or AutoDome cameras
Monitor(s)
DCN software V8.00 or higher
Temporary installation PC with two Comports
Software LBB3562 V1.0 or higher
Stand Alone Camera Control

31. Keep in mind
If you have DCN software V9.30 or higher then you need LBB3562 V2.0 or higher
Otherwise it will not work.
Stand Alone Camera Control

32. Step 1 Connect Camera(s),Monitor(s) and Keyboard to Video Switcher
Stand Alone Camera Control

33. Step 2 Connect PC to Allegiant Switcher and CCU
Temporary PC
with two Comports
DCN CCU
RS232
RS232
Allegiant Switcher
Baudrate 19.2K
Baudrate 19.2K
Stand Alone Camera Control

34. Keep in mind !! The default COM port settings are:
Com 1 for communication with the CCU Com 2 for communication with the Video Switcher
Stand Alone Camera Control

35. Step 3 CCU protocol and Serial Port settings
LBB3500/05
Make sure that the port you use
of the CCU is set to :
Protocol = Camera Control Baudrate = 19.2K
Keep in mind !!
The default setting for the LBB3500/05 is :
Port 1 Protocol = Camera Control Baudrate = 19.2K
Stand Alone Camera Control

36. The default settings for the LBB3500/15 &LBB3500/35 is :
Port 1 Protocol = Full Baudrate = 115.2K
Port 2 Protocol = Camera Control Baudrate = 19.2K
Keep in mind !!
Stand Alone Camera Control

37. If you are using the LBB3500/15 or /35 make sure you connect the RS232 cable to Port 2.
Stand Alone Camera Control

38. Step 4 Install Camera Control software LBB3562
Stand Alone Camera Control

39. Make sure you choose the configuration with Allegiant Video Switcher
Stand Alone Camera Control

40. Step 5 Start Camera Installation software
Stand Alone Camera Control

41. Step 6 Set Pre-Positions using the Video Switcher Keyboard
Stand Alone Camera Control

42. Step 7 Combine seat numbers with camera pre positions
Stand Alone Camera Control

43. Stand Alone Camera Control
Stand Alone Camera Control

44. 5
Stand Alone Camera Control

45. Step 8 Connect CCU to Allegiant Video Switcher
DCN CCU
Allegiant Switcher
RS232
Baudrate 19.2K
Baudrate 19.2K
Stand Alone Camera Control

46. How to configure Stand Alone Camera Control
End of section
 Robert Bosch GmbH
All rights are reserved. Reproduction or passing on to third parties in whole or in parts is prohibited without the written consent of the copyright owner.
Stand Alone Camera Control