1. Dry Run 0
Week 13:
BI test of...everything circulating beam: all fixed displays and BI applications
OP directories for 2009, concentrators running
Need to have an operational Hyper Cycle (another one to test software)
MCS tests of:
Check all existing critical settings after RBAC release
LHC BLMs, CISx (SMP parameters)....maybe collimators
MKI ExpertSettings and SoftstartSettings, BetsBem, BetsBei, IPOC, MKD and MKB critical settings test
Point 6 interlocked BPMs (BPMITLHC)....which role to be used: ABT is for MCS-BT-LBDS
BPMSA.A4L6.B1/InterlockSetting
BPMSB.A4R6.B1/InterlockSetting
BPMSB.A4L6.B2/InterlockSetting
BPMSA.A4R6.B2/InterlockSettin
Only missing then for start-up: maybe collimators, FEI

2. Program for Wednesday week 13 - BI
Check application + logging + fixed display:
YASP orbit + FIFO: will have simulated data
Multiturn ← capture events for BPMs
BLMs: running sums and capture events
NEED TO MAKE SURE THAT ENERGY IS LOGGED
Abortgap Monitor
BCTs
Wire scanners, synchrotron light monitor
LHC timing BTVs – will play sequencer driven timing tables
Proxies → fixed displays and application; logging?
NO beam dumped events, NO post mortem events
Tune: wait for Ralph...

3. Dry Run I – injection equipment
week 14 (2nd and 3rd of April) and week 15 (for BI rather)
MKI 8: run it from control room
New softstart
OASIS: BCT + MKIs; logging
Beam permit loops: need to jumper out also injection BICs
Energy OK from energy from simulation
Application??: need to make sure that can run it through LSA
Application will be ready in week 16 only → SM18 shifts
Timing: ready for week 14 Test mode stuff (need to verify!!) → got from Jean-Claude: first version will be ready: need to have a little application as well. Just ONE button (only as lhcop).
RF needs to generate the pre-pulse: Andy told me should be OK
Fixed displays
TI 8 and TI 2
Critical settings for FEI? Prepare DC functions (can’t run it...interlocked)
All BI, usual stuff
Logging for new BPMs...new logging for the PC
Injection BI: again concentrators (BLM [also capture] and BPM), injection region BTVs, run injection tables
BTV proxies: for all SPS BTVs

4. Dry Run II Week 17 (23rd and 24th of April) - Injection
Beam 1 and beam 2 injections if possible with the BIS
MKI 2 like before
Week 17 – LBDS software
LBDS monitoring application (no functional test yet, only communication): needs RBAC for the acknowledge
Arming of IPOC and BETS testable (BetsSim) → test new sequences as far as possible
Also, the new CIBG generators and communication with it...for the time being LBDS jumpered out
XPOC (play-back mode), logging
Dump line BI with XPOC events (should trigger XPOC): fixed displays
FBCTs, BLMs, BTVs, BPMs (interlocked BPM), Abort gap monitor

5. Dry Run III
Week
TT40/TT60 beam tests
Will take out some time from CNGS for TT40.
Test of mastership business:
Injection sequencer fully available
(new mastership request: don’t need to remove user request to become master, can become master also when in spare (if tagged TO_LHC, but no dynamic destinations under spare); new mastership request removes: TI8_dump/TI2_dump request and sets requested batches to zero and does the same thing again when removing mastership; SIS also verifies that if dynamic destination is TI8_dump or TI2_dump the downstream TEDs must be in)
Would be good to have first version of IQC integrated in injection sequencer
Date not defined yet: during MD without extraction (long LHC cycle): requesting different filling patterns (different # batches) under LHC mastership

6. Planning for the next stuff...
As soon as we have a little bit of experience with the first dry runs, we plan the next ones.
Beam dump we can only fully test from the control room from week 29 (beam 2).
Need to test as much as possible before...need to figure that out.
MKQA and AC Dipole not covered yet.