1. Electrical Engineering Lab I
EECE 1101
Electrical Engineering Lab I

2. Taaruf Nor Farahidah Za’bah Room number : E2-2-13.12
Phone number :
address :
The lab technician is
Br. Shahbudin bin Basri
The lab demonstrator is Br. Sazib
Course website:
Taaruf

4. Weeks Topics Task/Reading Preparation Week 2 Introduction to Lab 33
Experiment #1: Ohm’s Law & Series and parallel circuits
Experiment #1 4
Experiment #2: Kirchoff’s voltage and current laws
Experiment #2 5
Experiment #3: Thevenin’s and Norton’s theorem and Maximum power transfer theorem
Experiment #3 6
Experiment #4: Superposition Theorem
Experiment #4 7
Introduction to Simulation Software PSPICE 8
Experiment #5: Diode Characteristic and Application
Experiment #5 9
Experiment #6: Inverting and Non-Inverting Op-Amp (Theoretical and Demonstration)
Experiment #6
Design an Amplifier using Op-Amp (Open-Ended Lab) 10
Experiment #7: BJT Characteristic and Biasing Circuits
Experiment #7
12 & 13
Preparation Week 14
Final Test

5. Assessment Item % Quizzes 10 Reports 25 Open Ended Lab PSPICE 5
Final Examination 50
TOTAL
100

6. Safety
Please wear covered shoes – NO SLIPPERS. Otherwise, you will be asked to leave the lab.
Power must be switched off whenever an experiment or project is being assembled, disassembled, or modified.

7. Tidiness
When the experiment has been satisfactory completed and the results approved by the instructor, the students may disconnect the circuit and return the components and instruments to the locker tidily.
Chairs are to be slid in properly.
DO NOT WRITE anything on the table

8. Preparation
Read the entire experiment and research any required theory beforehand. Many times an experiment takes longer that one class period simply because a student is not well prepared.
The experiment is performed in pairs (max=3 students per group) but the final test is performed individually
One group = one lab report

9. Preparation for PSPICE Tutorial
Download 16.6_OrCAD_Lite_Capture&PSpice_Products.zip from the any computer in the lab
It is a zipped file, you have to extract the files into a designated folder
Once you have extracted, go to Disk 1 and look for SETUP (it is an application file) to install the software.
One group will require ONE laptop for the tutorial sessions

10. SEPTEMBER M T W F S 3 4 5 6 7 8 9
Intro 10 11 12 13 14 15 16
Lab 1 17 18 19 20 21 22 23
No Lab 24 25
 26
Lab 2
OCTOBER  1  2
 Lab 3
 Lab 4
PSPICE  26 27 28   
Lab 5 29 30 31
 MID SEMESTER BREAK  

11. NOVEMBER M T W F S 5 6 7 8 9 10 11 Deepavali 12 13 14 15 16 17 18 5 6   7  8  9 10 11
Deepavali
Lab 6 – Theoretical/
Demonstration 12 13 14 15 16 17 18
 Lab 6 – Open Ended Lab  19 20 21 22 23 24 25
Lab 7 26 27 28 29 30
DECEMBER 3 4 5 6 7 8 9
Final Test
Final Exam Starts

12. Introduction to Lab Equipment
Bread board and its connections
Holes that are labelled with letters means SAME node

14. Function Generator
To create AC signals such as Sine-Wave, Triangular Waves and Square Wave
The user can alter its frequency and amplitude
Example of a function generator

15. Oscilloscope An equipment to show the obtained result. Has 2 channels
One for input signal
One for output signal

16. DC power supply
To provide DC supply to your circuit which you can measure using digital multi-meter
Only use channel 1 and channel 3
Make sure the overload light is off
Increase the current knob

17. Digital Multimeter (DMM)
To measure voltage, turn the knob to DC Volts
The DMM is place ACROSS/IN PARALLEL with the device that you are measuring
To measure current, turn the knob to AC (mA)
The lead is place IN SERIES with the path where the current flows
Main reason why DMM failed to work as Ammeter is because students tend to short circuit the two leads.

18. x
+Vs
GND y
+VS
GND
1 k x y

19. SERIES
PARALLEL x A x y y