1. PABX with Caller ID MS48C

2. MS48C is now ready for exports!!! Ergonomic Design in Plastic Cabinet Caller ID Detection SMS Transmission MS48C - PABX with Caller ID

3. Allows sending / receiving SMS through standard extensions as an option. Detects and displays Caller ID on standard extensions equipped with Caller ID sets as an option. Supports all add-ons / features of MS48S (except for ID12). Holds battery switch which is accessible without opening the cover. BT104 Low End Keyphone. BT104 Caller ID Telephone is an appropriate choice for New MS48C (with Caller ID) as a Low End Keyphone. MS48C - PABX with Caller ID

4. Caller ID (CLID) & SMS can be integrated via EXP48C-CLID card. This card is to be installed on top of the motherboard if there are no expansion modules or on the lastly installed expansion module otherwise. MS48C - PABX with Caller ID N.C. – Used for Firmware Changes N.C. – Used for Debugging KTS Input of CLID Module KTS Output to Consoles

5. The expansion modules of MS48C are called EXP48C. EXP48S expansion modules of MS48S can also be used with MS48C. But CLID is not supported on the lines and extensions of EXP48S modules. MS48C - PABX with Caller ID

6. No need to make separate grounding for EXP48C Expansion Modules. EXP48C is grounded once it is installed on the motherboard through a ground pin on the motherboard. MS48C - PABX with Caller ID All ground cables are collected at this point. MS48C should be grounded from this ground terminal. Ground Pin for EXP48C

7. Extension / line connectors allow vertical cabling. The position of connectors has been changed from horizontal to vertical. MS48C - PABX with Caller ID CABLE HOLE CABLE CHANNELS CONNECTORS

8. 12V- 7Ah battery can be located under the battery belt inside the cabinet. MS48C - PABX with Caller ID BATTERY CONNECTION BATTERY BELT

9. MS48C - PABX with Caller ID SPS48 Power Card with transformers are surrounded by portable plastic casing. PRESS SLIDE

10. MS48C - PABX with Caller ID HOW TO OPEN THE CABINET

11. MS48C - PABX with Caller ID HOW TO ACCESS POWER & BATTERY SWITCHES POWER SWITCH BATTERY SWITCH

12. MS48C - PABX with Caller ID HOW TO MOUNT MS48C ON THE WALL Drive the screws to the wall Drive the screws to the wall Hook the system on the screw through the peer holesHook the system on the screw through the peer holes Fix the third screw to the wallFix the third screw to the wall

13. MS48C detects Caller ID in FSK or DTMF through C.O. Lines. MS48C sends Caller ID in FSK to standard extensions. Caller ID can be displayed on standard CLID telephones with feed voltage not higher than 24V. Line impedance is 900/1800 Ohm, complex impedance. MS48C - PABX with Caller ID

14. The dimensions and weight of MS48S and MS48C are different from each other. Dimensions of MS48C are 39 cm x 13 cm (h) x 48 cm and its weight is 5 kg Dimensions of MS48S were 38 cm x 11 cm (h) x 43 cm and its weight is 8.25 kg With the launch of MS48C, MS48S is now obsolete. The motherboard, expansion modules and accessories of MS48S will continue to be available as spare parts only. MS48C - PABX with Caller ID

15. Technical Specifications Basic Capacity4/12 Expandable By2/6, 4/12, 0/16 Two boards can be installed on the basic capacity. Only one can be 2/6 or 0/16 Max. Capacity48 Ports Line InterfaceLoop Start with DP/DTMF Signalling Extension InterfaceStation Loop 1200 Ohms Including Set Power230 VAC, 50 Hz; Optional. 12V Bat. Backup Power Consumption11W (Stand-by) Environment0 °C to 45 °C to 80% Humidity Dimensions39x13x48 cm Weight5 kg (Basic capacity without battery) MS48C - PABX with Caller ID