1. VIDAS Blue Presentation - JD - 22 juin 2005

2. VIDAS BLUE PRESENTATION
VIDAS Blue Presentation - JD - 22 juin 2005

3. VIDAS BLUE VIDAS BLUE: New Vidas and mini Vidas look
VIDAS Blue Presentation - JD - 22 juin 2005

4. The main changes VIDAS BLUE
VIDAS Blue Presentation - JD - 22 juin 2005

5. VIDAS BLUE
VIDAS Blue Presentation - JD - 22 juin 2005

6. VIDAS BLUE
Blue tray covers
Strip preparation tray

7. strip preparation tray
VIDAS BLUE
Removing
strip preparation tray

8. Mini VIDAS BLUE

9. Mini VIDAS BLUE
New screen / keyboard Holder
New printer paper
holder

10. VIDAS BLUE
Internal changes

11. VIDAS BLUE
On mini VIDAS:
Addition of a long screw to fix the right trim

12. VIDAS BLUE
On mini VIDAS:
Screen/keyboard holder 3 fixing points:

13. VIDAS BLUE
New Power Supply Assembly:
Only 4 external points of fixation (4 screw)
Central chimney (V30)
No railing(bar)

14. VIDAS BLUE
New Power Supply Assembly:
- Only 1 Power Supply Board (V12/V30)
- 1 air fan
- Self switching Power Supply (110/220V)

15. New Power Supply Board:
VIDAS BLUE
New Power Supply Board:
Dedicated mini Vidas and Vidas connectors.
VIDAS
Mini VIDAS
Be carefull
Respect the correct connector!

16. Fixed by 4 plastic retainers
Spare part
If Air Fan out of service:
Software T° error will be
generated
Automatic Power Supply
cut off
VIDAS BLUE
New Power Supply Board:
Air Fan

17. New tray ball bearings:
VIDAS BLUE
New tray ball bearings:
Excentric ball bearing
replaced by a normal
one fixed on a spring
mechanism.
No more lateral play to adjust

18. VIDAS BLUE Tray motor assembly: Addition of a pretensionning spring
CAUTION!
Lock the motor Assy
when it is
in the good position
Addition of a pretensionning spring

19. VIDAS BLUE Tower screw: To reduce the tower misalignments
Addition of a spacer
To reduce the tower misalignments

20. VIDAS BLUE Incubator door: - New door plunger ball nut
- Addition of a safety latch

21. VIDAS BLUE
New electronic boards:
Incubator Boards
Scanner Board

22. VIDAS BLUE New Scanner Board: New Power Supply 3.3V LED
Flash ROM U5 ( V2.51)
(replace the EEPROM)
Sensors LEDs
DIP Switch SW3
(replace JP7/JP8/JP9)
Scanner cable breakdown detection
LEDs
Power Supply LEDs
(+5V/+10V/+12V/-12V)
Communication LEDs
Mini Vidas Blue Backlight
Power Supply connector
J15: Scanner Cable new
Connector for failure detection
(replace coax. cables )

23. VIDAS BLUE New Scanner Board: 100 % compatible with the old boards
One Flash ROM V 2.51 instead of 3 EPROM V2.41
100 % compatible with the old boards
SW3 replaces Jumpers JP7 to JP9
New power supply 3,3V
New connector (J18) dedicated to the mini Vidas screen backlight power supply.
New connector (J15) for scanner failure detection ( replaces coax cables)
REF. SCANNER BOARDS : VD8201-1

24. VIDAS BLUE

25. VIDAS BLUE

26. VIDAS BLUE New Incubator Board: Double support Flash ROM U5
or EPROM V 3.10
Power Supply LEDs
Heaters LEDs
DIP switch SW2
(replace adress/
reset jumpers)
Serial communication
with scanner board
LEDs
Sensor LEDs

27. VIDAS BLUE New Incubator Board: 100% compatible with the old boards
Available with EPROM 3.10 or Flash ROM
(same version)
VIDAS BLUE
New Incubator Board:
100% compatible with the old boards
Dip Switch SW2 replace all Adress and Reset jumpers ( silkscreen directly on the board).
LEDS for Power Supply, communication,
sensors and heaters.
Fuses (SMD) F1 to F4
REF. INCUB.Board : VD8202-2

28. VIDAS BLUE

29. VIDAS BLUE

30. VIDAS BLUE SCANNER: new parts New mini VIDAS/ VIDAS scanner cables
New scanner cables with failure detection
(replace coaxial cables)
The blue flat cable is still the same

31. VIDAS BLUE SCANNER: new parts New Scanner PRE-AMP board
J1 connector unchanged, use with
both old scanner câble kits and new
Scanner cables.
New J2 connector, is only used with
new scanner cables and new scanner
Board.
(Allows scanner cable failure detection)

32. VIDAS BLUE : reminder
The scanner cable failure detection system is available only
with a new Scanner Cable, new Scanner Board,
and new Scanner Head.
The LEDs (DS9 to DS12 from the new scanner board) are on
When a cable is broken.
( off = cables OK)
If a scanner cable failure is detected, a blocking error 161 will be generated.
The new Scanner head is compatible with the old Scanner head
But  don’t forget to replace the new scanner cable by an old
scanner cable kit in order to be compatible with the old scanner
board

33. VIDAS BLUE Changes impact
Decontamination:  a new procedure has been defined to take
Into account the « Strip preparation tray ».
Error 161:  If err. 161, check the integrity of the scanner cables. ( LEDs off on scanner board = good)
PM : Scanner cable replacement every 2 years
 Non Applicable
PM :  tray lateral play not necessary to set
PM : Power Supply  not necessary to open it during a PM
(If dead, replace the complete block.)

34. VIDAS BLUE Compatibility table
(*) Scanner Head Blue : put an old scanner cable kit
(**) Scanner Cable Blue: only used with a new Scanner Head and new Scanner Board.
VIDAS Blue Presentation - JD - 22 juin 2005

35. VIDAS BLUE You will receive a specific Mandatory Action Required (MAR)
from GCS soon.
More details will be added in this MAR .
Feel free to contact us for many information :