Presentation is loading. Please wait.

Presentation is loading. Please wait.

MULTISTAGE AMPLIFIERS

Similar presentations


Presentation on theme: "MULTISTAGE AMPLIFIERS"— Presentation transcript:

1 MULTISTAGE AMPLIFIERS

2 Multistage Amplifiers
Two or more amplifiers can be connected to increase the gain of an ac signal. The overall gain can be calculated by simply multiplying each gain together. A’v = Av1Av2Av3 …… Fig 6-32

3 Introduction Many applications cannot be handle with single-transistor amplifiers in order to meet the specification of a given amplification factor, input resistance and output resistance As a solution – transistor amplifier circuits can be connected in series or cascaded amplifiers This can be done either to increase the overall small-signal voltage gain or provide an overall voltage gain greater than 1 with a very low output resistance

4 Multistage Amplifiers
Multi-stage amplifiers are amplifier circuits cascaded to increased gain. We can express gain in decibels(dB). Two or more amplifiers can be connected to increase the gain of an ac signal. The overall gain can be calculated by simply multiplying each gain together. A’v = Av1Av2Av3 …… Fig 6-32

5 Example Find Vout Vin = 5 mV Av3 = 6 Avn = 8 Fig 6-32 Av1 = 5 Av2 = 10

6 Multistage Amplifier Cutoff Frequencies and Bandwidth
When amplifiers having equal cutoff frequencies are cascaded, the cutoff frequencies and bandwidth of the multistage circuit are found using

7 Introduction (cont.) Multistage amplifier configuration:
Cascade /RC coupling Cascode Q2 Q1 Q2 Q1 Transformer coupling Darlington/Direct coupling

8 i) Cascade Connection The most widely used method
Coupling a signal from one stage to the another stage and block dc voltage from one stage to the another stage -The signal developed across the collector resistor of each stage is coupled into the base of the next stage -The overall gain = product of the individual gain **refer page 219

9 i) Cascade Connection (cont.)
small signal gain is: by determine the voltage gain at stages 1 & stage 2 therefore - the gain in dB input resistance Output resistance - assume ,so also Therefore

10 Exercise 1: Draw the ac equivalent circuit and calculate the voltage gain, input resistance and output resistance for the cascade BJT amplifier in above Figure. Let the parameters are:

11 Solution 1 (cont.): Ac equivalent circuit for cascade amplifier

12 Solution 1: DC analysis: At Q1: At Q2: AC analysis:
Why the Q-point values same for both Q1 & Q2 ?

13 Solution 1 (cont.): From the ac equivalent circuit:
At Q1, the voltage gain is: Where is the o/p voltage looking to the Q1 transistor and is the i/p resistance looking into Q2 transistor Therefore The voltage gain at Q1 is:

14 Solution 1 (cont.): From the ac equivalent circuit:
At Q2, the voltage gain is: Where is the i/p voltage looking into the Q2 transistor Therefore, the voltage gain at Q2 is: The overall gain is then, ** The large overall gain can be produced by multistage amplifiers!! So, the main function of cascade stage is to provided the larger overall gain

15 Solution 1 (cont.): From the ac equivalent circuit:
The i/p resistance is: The o/p resistance is:

16 ii) Cascode Connection
-A cascode connection has one transistor on top of (in series with) another -The i/p into a C-E amp. (Q1) is, which drives a C-B amp. (Q2) -The o/p signal current of Q1 is the i/p signal of Q2 -The advantage: provide a high i/p impedance with low voltage gain to ensure the i/p Miller capacitance is at a min. with the C-B stage providing good high freq. operation **refer page 223

17 ii) Cascode Connection (cont.)
From the small equivalent circuit, since the capacitors act as short circuit, by KCL equation at E2: solving for voltage Where the output voltage is or

18 ii) Cascode Connection (cont.)
Therefore the small signal voltage gain: From above equation shows that: So, the cascode gain is the approximately * The gain same as a single-stage C-E amplifier

19 iii) Darlington Connection
-The main feature is that the composite transistor acts as a single unit with a current gain that is the product of the current gains of the individual transistors -Provide high current gain than a single BJT -The connection is made using two separate transistors having current gains of and So, the current gain If The Darlington connection provides a current gain of Figure 1: Darlington transistor

20 iii) Darlington Connection (cont.)
Figure shown a Darlington configuration refer page 222

21 iii) Darlington Connection (cont.)
The small current gain : Since Therefore Then, The o/p current is: The overall gain is: ** The overall small-signal current gain = the product of the individual current gains

22 iii) Darlington Connection (cont.)
The input resistance: Known that: So, the i/p resistance is: The base of Q2 is connnected to the emitter of Q1, which means that the i/p resistance to Q2 is multiplied by the factor , as we saw in circuits with emitter resistor. So, we can write: and Therefore The i/p resistance is then approximately **The i/p resistance tends to be large because of the multiplication


Download ppt "MULTISTAGE AMPLIFIERS"

Similar presentations


Ads by Google