Presentation is loading. Please wait.

Presentation is loading. Please wait.

SI Engine Cycle Actual Cycle Intake Stroke Compression Power Exhaust

Published byDwain Kelley Modified over 5 years ago

Similar presentations

Presentation on theme: "SI Engine Cycle Actual Cycle Intake Stroke Compression Power Exhaust"— Presentation transcript:

1 SI Engine Cycle Actual Cycle Intake Stroke Compression Power Exhaust
Combustion Products Ignition Intake Stroke FUEL Fuel/Air Mixture Compression Power Exhaust Actual Cycle

2 Actual SI Engine cycle Total Time Available: 10 msec Ignition

3 Early CI Engine Cycle Actual Cycle Intake Stroke Compression Power
Combustion Products Fuel injected at TC Intake Stroke Air Compression Power Exhaust Actual Cycle

4 Modern CI Engine Cycle Actual Cycle Intake Stroke Compression Stroke
Fuel injected at 15o bTC A I R Air Combustion Products Actual Cycle Intake Stroke Compression Stroke Power Stroke Exhaust Stroke

5 Thermodynamic Cycles for CI engines
In early CI engines the fuel was injected when the piston reached TC and thus combustion lasted well into the expansion stroke. In modern engines the fuel is injected before TC (about 15o) Fuel injection starts Fuel injection starts Early CI engine Modern CI engine The combustion process in the early CI engines is best approximated by a constant pressure heat addition process  Diesel Cycle The combustion process in the modern CI engines is best approximated by a combination of constant volume and constant pressure  Dual Cycle

6 Thermodynamic Modeling
The thermal operation of an IC engine is a transient cyclic process. Even at constant load and speed, the value of thermodynamic parameters at any location vary with time. Each event may get repeated again and again. So, an IC engine operation is a transient process which gets completed in a known or required Cycle time. Higher the speed of the engine, lower will be the Cycle time. Modeling of IC engine process can be carried out in many ways. Multidimensional, Transient Flow and heat transfer Model. Thermodynamic Transient Model USUF. Fuel-air Thermodynamic Mode. Air standard Thermodynamic Model.

7 Ideal Thermodynamic Cycles
Air-standard analysis is used to perform elementary analyses of IC engine cycles. Simplifications to the real cycle include: 1) Fixed amount of air (ideal gas) for working fluid 2) Combustion process not considered 3) Intake and exhaust processes not considered 4) Engine friction and heat losses not considered 5) Specific heats independent of temperature The two types of reciprocating engine cycles analyzed are: 1) Spark ignition – Otto cycle 2) Compression ignition – Diesel cycle

8 Otto Cycle Actual Cycle Qin Qout Otto Cycle Intake Stroke Compression
Combustion Products Ignition Intake Stroke FUEL Fuel/Air Mixture Compression Power Exhaust Actual Cycle Otto Cycle Air TC BC Qin Qout Compression Process Const volume heat addition Expansion heat rejection Otto Cycle

9 Air-Standard Otto cycle
Process 1 2 Isentropic compression Process 2  3 Constant volume heat addition Process 3  4 Isentropic expansion Process 4  1 Constant volume heat rejection Compression ratio: Qin Qout v2 TC v1 BC TC BC

10 First Law Analysis of Otto Cycle
12 Isentropic Compression AIR 23 Constant Volume Heat Addition Qin AIR TC

11 Qout 3  4 Isentropic Expansion 4  1 Constant Volume Heat Removal BC
AIR 4  1 Constant Volume Heat Removal Qout AIR BC

12 First Law Analysis Parameters
Net cycle work: Cycle thermal efficiency: Indicated mean effective pressure is:

13 Effect of Compression Ratio on Thermal Efficiency
Typical SI engines 9 < r < 11 k = 1.4 Spark ignition engine compression ratio limited by T3 (autoignition) and P3 (material strength), both ~rk For r = 8 the efficiency is 56% which is twice the actual indicated value

14 Effect of Specific Heat Ratio on Thermal Efficiency
ratio (k) Cylinder temperatures vary between 20K and 2000K so 1.2 < k < 1.4 k = 1.3 most representative

15 Factors Affecting Work per Cycle
The net cycle work of an engine can be increased by either: i) Increasing the r (1’2) ii) Increase Qin (23”) 3’’ P 3 (ii) 4’’ Qin 4 Wcycle 4’ 2 (i) 1 1’ V2 V1

16 Effect of Compression Ratio on Thermal Efficiency and MEP
k = 1.3

17 Ideal Diesel Cycle Qin Qout BC Compression Process Const pressure
Air BC Qin Qout Compression Process Const pressure heat addition Expansion Const volume heat rejection

18 Air-Standard Diesel cycle
Process 1 2 Isentropic compression Process 2  3 Constant pressure heat addition Process 3  4 Isentropic expansion Process 4  1 Constant volume heat rejection Cut-off ratio: Qin Qout v2 TC v1 BC TC BC

19 Thermal Efficiency For cold air-standard the above reduces to: recall, Note the term in the square bracket is always larger than one so for the same compression ratio, r, the Diesel cycle has a lower thermal efficiency than the Otto cycle Note: CI needs higher r compared to SI to ignite fuel

20 When rc (= v3/v2)1 the Diesel cycle efficiency approaches the
Thermal Efficiency Typical CI Engines 15 < r < 20 When rc (= v3/v2)1 the Diesel cycle efficiency approaches the efficiency of the Otto cycle Higher efficiency is obtained by adding less heat per cycle, Qin,  run engine at higher speed to get the same power.

21 Thermodynamic Dual Cycle
Air TC BC Qin Qout Compression Process Const pressure heat addition Expansion Const volume heat rejection Dual Cycle

22 Process 1  2 Isentropic compression
Dual Cycle Process 1  2 Isentropic compression Process 2  2.5 Constant volume heat addition Process 2.5  3 Constant pressure heat addition Process 3  4 Isentropic expansion Process 4  1 Constant volume heat rejection 3 Qin 2.5 3 2 Qin 2.5 4 2 4 1 1 Qout

23 Thermal Efficiency Note, the Otto cycle (rc=1) and the Diesel cycle (=1) are special cases:

24 The use of the Dual cycle requires information about either:
the fractions of constant volume and constant pressure heat addition (common assumption is to equally split the heat addition), or ii) maximum pressure P3. Transformation of rc and  into more natural variables yields For the same inlet conditions P1, V1 and the same compression ratio: For the same inlet conditions P1, V1 and the same peak pressure P3 (actual design limitation in engines):

25 For the same inlet conditions P1, V1
and the same compression ratio P2/P1: For the same inlet conditions P1, V1 and the same peak pressure P3: Pmax “x” →“2.5” Pressure, P Pressure, P Po Po Specific Volume Specific Volume Tmax Otto Dual Diesel Diesel Temperature, T Dual Temperature, T Otto Entropy Entropy

Download ppt "SI Engine Cycle Actual Cycle Intake Stroke Compression Power Exhaust"

Similar presentations

Ideal Intake and Exhaust Strokes

Ideal Intake and Exhaust Strokes
Engine Geometry BC L TC l VC s a q B

Engine Geometry BC L TC l VC s a q B
THERMAL ENGINEERING (ME 2301 )

THERMAL ENGINEERING (ME 2301 )
Conceptual & Thermodynamic Description of Expansion in I.C. Engine P M V Subbarao Professor Mechanical Engineering Department The Actual & Useful Extent.

Conceptual & Thermodynamic Description of Expansion in I.C. Engine P M V Subbarao Professor Mechanical Engineering Department The Actual & Useful Extent.
This Week > POWER CYCLES

This Week > POWER CYCLES
Department of Mechanical Engineering ME 322 – Mechanical Engineering Thermodynamics Lecture 28 Internal Combustion Engine Models The Otto Cycle The Diesel.

Department of Mechanical Engineering ME 322 – Mechanical Engineering Thermodynamics Lecture 28 Internal Combustion Engine Models The Otto Cycle The Diesel.
Effect of Piston Dwell on Engine Performance P M V Subbarao Professor Mechanical Engineering Department Sufficiency of time to Execute a Process…..

Effect of Piston Dwell on Engine Performance P M V Subbarao Professor Mechanical Engineering Department Sufficiency of time to Execute a Process…..
Creation of Ideal Cycles for Internal Combustion Engines P M V Subbarao Professor Mechanical Engineering Department Basic Thermodynamic Structure of an.

Creation of Ideal Cycles for Internal Combustion Engines P M V Subbarao Professor Mechanical Engineering Department Basic Thermodynamic Structure of an.
İsmail ALTIN, PhD Assistant Professor Karadeniz Technical University Faculty of Marine Sciences Department of Naval Architecture and Marine Engineering.

İsmail ALTIN, PhD Assistant Professor Karadeniz Technical University Faculty of Marine Sciences Department of Naval Architecture and Marine Engineering.
Internal Combustion Engine Theory

Internal Combustion Engine Theory
Gas Power Cycles Cengel & Boles, Chapter 8 ME 152.

Gas Power Cycles Cengel & Boles, Chapter 8 ME 152.
GAS POWER CYCLES Chapter 9. Introduction Two important areas of application for thermodynamics are power generation and refrigeration. Two important areas.

GAS POWER CYCLES Chapter 9. Introduction Two important areas of application for thermodynamics are power generation and refrigeration. Two important areas.
EGR 334 Thermodynamics Chapter 9: Sections 1-2

EGR 334 Thermodynamics Chapter 9: Sections 1-2
Shaft Power Generation Devices - 1

Shaft Power Generation Devices - 1
Diesel / Brayton Cycles

Diesel / Brayton Cycles
Thermodynamic Analysis of Internal Combustion Engines P M V SUBBARAO Professor Mechanical Engineering Department IIT Delhi Work on A Blue Print Before.

Thermodynamic Analysis of Internal Combustion Engines P M V SUBBARAO Professor Mechanical Engineering Department IIT Delhi Work on A Blue Print Before.
For next time: Read: § 8-6 to 8-7 HW11 due Wednesday, November 12, 2003 Outline: Isentropic efficiency Air standard cycle Otto cycle Important points:

For next time: Read: § 8-6 to 8-7 HW11 due Wednesday, November 12, 2003 Outline: Isentropic efficiency Air standard cycle Otto cycle Important points:
Gas Power Cycle - Internal Combustion Engine

Gas Power Cycle - Internal Combustion Engine
INTERNAL COMBUSTION ENGINES (reciprocating). Geometry.

INTERNAL COMBUSTION ENGINES (reciprocating). Geometry.
Thermodynamic Cycles Air-standard analysis is a simplification of the real cycle that includes the following assumptions: 1) Working fluid consists of.

Thermodynamic Cycles Air-standard analysis is a simplification of the real cycle that includes the following assumptions: 1) Working fluid consists of.

Similar presentations

Ads by Google