1. AMC13 Status Report
AMC13 Update

2. AMC13 Status Reminder Version 1 (5Gb/s links, Virtex-6 chip)
15 modules built, all but 3 distributed to colleagues
1 at P5 ready for Slice test
Version 2 (10Gb/s links, Kintex-7 chip)
Design ready to send out, expect to send in next days
Prototypes ready in min-January
AMC13 Update

3. AMC13 Rev 2 Changes Virtex 6 to Kintex 7 for 10G link support
Two-way GbE switch removed, GbE to Spartan chip only
(Never used Virtex GbE option)
SDRAM size increased from 128MB to 512MB speed to 800MHz DDR (1600MT/s * 16 bits)
Clock source changes:
Rev 1 used 2x Si570 programmable XO
Rev 2 uses Si5338B Quad programmable clock generator
TTC Recovered clock to clock-capable input on Kintex 7
Changes to T1-T2 board connector pinout
Maintain plug compatibility with existing connector
Add 1 pin for additional 12V to be routed to T3 (plus additional GND)
There are two diff pairs unused (GPIO pairs) unused for CLK, TTC
AMC13 Update

4. TTC / TTS Tester VME (or benchtop) module TTS fiber-to-RJ45 translator
TTC system simulator
10 pieces at assembly house, overdue!
Firmware underway; basic version running, fancy version with IPBus control in development
AMC13 Update

5. TTC/TTS Tester Diagram
AMC13 Update

6. Reserve Slides
AMC13 Update

7. Kintex 7 AMC13 Module – Rev 2 CLK F/O 40.xx CLK To AMCs TTC in SFP
CDS
TTC in
TTS out
Kintex 7
SFP IO IO
DAQ
10 Gb/s
SFP+
GTX
GTX
GTX
GTX
Fabric A (DAQ)
12 ports
5.0 Gb/s
GTX
GTX
DAQ
10 Gb/s
SFP+
GTX
GTX
GTX
GTX
GTX
Spare
10 G b/s
SFP+
(2) 128Mx16
DDR3
GTX
1600MT/s (6.4 GB/s)
Spartan 6
GTP IO
Fabric B
80 Mb/s (TTC)
DC LVDS
GbE
GTP
MCH1
MMC uC
IPMI
Front
Panel
via T3
JTAG
LEDs
SPI Flash
(4x GPIO)
AMC13 Update

8. SDRAM Update
Rev 1:
(1) MT41J64M16LA M x 16 DDR3 Tested at 1600 MT/s (800 MHz)
Rev 2:
(2) MT41J128M16JT M x 16 DDR3 Speed rated to 1866 MT/s (933 MHz) Plan to operate at 1600 MT/s (800 MHz)
This part promised long-term availability by Micron factory rep
AMC13 Update

9. New clock source
AMC13 Update

10. T1-T2 connectors MMC T2 → T1 SPI Bus Switch, LEDs Propose to add
1-2 pins PWR12V
Connector can
expand this way only
2.5Gb/s
T1 ↔ T2 link
GbE to T2
T1 → T2
TTC Data
40MHz clk
Spare GPIOs (4)
JTAG / Config
JTAG / Config
AMC13 Update

11. Clocks: Rev 1
AMC13 Update

12. Clocks: Rev 2
AMC13 Update

13. AMC13 Rev 1 Hardware Tongue 3 PCB (4) SFP+ Sites 1 for TTC (160Mb)
(optional, for initial programming)
(4) SFP+ Sites
1 for TTC (160Mb)
3 for DAQ/etc 6.2Gb
Atmel AVR-32 uC
MMC Functions
Micro USB
MMC serial console
Tongue 2 PCB
Tongue 1 PCB
Spartan 6 FPGA
Fabric B TTC distribution
Firmware management interface to MMC
Virtex-6 LX130T FPGA
DAQ Functions, buffering 6Gb links to backplane, SFP
JTAG Headers
MMC programming FPGA programming
AMC13 Update