2. Extended math functions – Standard
Square root-function: Math-channel delivers the square root of SQRT(X9) channel 9 value.
Also available: SIN(), COS(), TAN(), EXP(), ABS(), LOG(), a.s.o.

3. Extended math functions – Compare
Greater-than-function: Math-channel delivers 12,5 if value of channel 1 is greater than value of channel 2, otherwise it delivers value of channel 5.
Equal-function: Math-channel delivers 12,5 if value of channel 1 is greater than value of channel 2, otherwise it delivers value of channel 5.

4. Extended math functions – Logical
AND-function: Math-channel delivers 1 if results of mathematical calculation in channel 11 (M11) and channel 12 (M12) are unequal (All values unequal to zero are treated as logical 1!) zero.
Also available: OR, XOR, NOT

5. Extended math functions – Moving average
SM-function: Math-channel delivers the mean value of all values of channel 8 collected in the last 60 seconds.

6. Extended math functions – Special
MIN-function: Math-channel delivers the minimum value of channel 1 or channel 2
Also available: ITG(), MEAN(), MAX(), IDxxU(X,n), SDxxU(X,n)
FRAC-function: Math-channel delivers the position after the decimal point of channel 1

7. Extended math functions – Integrations
Summation -function: Math-channel adds up the values of channel 10 for 30 seconds. After 30 seconds IN30S(X10) the value of the MATH-channel is set to zero again.

8. Extended math functions – Paths
Click <Options>, <Path> or to open this window:
Select paths to your MATH-files.
Click <Edit functions> to make changes to your user functions.

9. Extended math functions – User functions 1
Select function number: This number is used in the project configuration later (F1, F2, a.s.o.).
Add a describing comment to the user function.
Add the mathematical formula.

10. Extended math functions – User functions 2
Function call in the MATH-line of the project configuration:
F1(X7,X8)
F1: It is used user function 001 from the selected user functions file.
X7: Raw value of channel 7 is assigned to character A in the formula ( A+B+SIN(A)+COS(B) ).
X8: Raw value of channel 7 is assigned to character B in the formula ( A+B+SIN(A)+COS(B) ).

11. Extended math functions – Polynomials 1
Select polynomial number: This number is used in the project configuration later (P1, P2, a.s.o.).
Add a describing comment to the user function.
Select kind of polynomial type:
This example: Power 2 based on 4 X-Y-pairs

12. Extended math functions – Polynomials 1
Click Display to show the resulting polynomial function The algorithm is based on the Least Square method and tries to find best possible fitting of sample points.

13. Extended math functions – Polynomials 2
Function call in the MATH-line of the project configuration:
P2: It is used polynomial 001 from the selected polynomial file.
X1: Raw value of channel 1 is assigned to character X in the formula P001 ( X^2 ) (best fit)

14. Extended math functions – Polynomials 3
This example:
Polynomial 5*X^3-7*X^2-2*+6
Based on coefficients.

15. Extended math functions – Polynomials 4
Function call in the MATH-line of the project configuration:
P2: It is used polynomial 002 from the selected polynomial file.
X1: Raw value of channel 1 is assigned to character X in the formula (5*X^3-7*X^2-2*X+6 )

16. Extended math functions – DLLs
Click <Configuration>, <MCPS settings…>, register card <DLLs>
It is possible to use customer specific DLLs to make complicated, not standard calculations.
Ask CAD Computer

17. Extended math functions – User curves 1
Open project configuration and click <Options>, <Defaults>, register card <User curves>. Click “Add curve”.
Example for a user curve configuration

18. Extended math functions – User curves 2
Result
User curve
Trend curve
Usable for
Controlling / setting analogue outputs
As alarm limit
As math values

19. Extended alarm functions – Types
There are up to 11 different types of alarms:
High alarm H
Low alarm L
Differential high alarm DH
Differential low alarm DL
Differential high saved alarm DHS
Differential low saved alarm DLS
Error ERR
Overflow OFL
Underflow UFL
High & Overflow H+OFL
Low & Underflow L+UFL

20. Extended alarm functions – Extended Delay
Reference channel
Delay time
Event condition
Restart delay timer on event
Enable / disable extended alarm delay
Possibility to
delay or
suspend
an alarm depending on the value of another channel.

21. Extended alarm functions – Options
Setup since when an occurring alarm is valid.
The alarm is active again when the limit exceeding is still valid and the alarm was already acknowledged.
The alarm obtains still valid and active although the channel data switches invalid

22. Extended alarm functions
Check connected hardware on external alarms
Use dynamic alarm file as limit for this channel / level

23. Export 1 Click <Project>, <Export>, <Channel data>.
Set time range of data to export
Select kind of export file
Select information to be exported
Average values to reduce the number scans to be exported

24. Export 2
Result of an export

25. Automation: printing
Open the project configuration and click <Options>, <Automation>,
register card <Print>
Select a trend display to be printed at the end of data acquisition.
Select statistic values to be printed periodic.
Select alarm information to be printed periodic.

26. Automation: Export
Open the project configuration and click <Options>, <Automation>,
register card <Export>
Set measurement data to be exported at the end of measurement
Set measurement data to be exported at the end of an Autofile
Set measurement value to be exported to a file with each scan

27. Process monitor 1
Open the project configuration and click <Project>, <Extras>, <Process monitoring editor>
Example of a preconfigured Process window.

28. Process monitor 2 Setup – tools for the process monitor
Add/Delete display page
Page configuration
Clear editor configuration
Return to selection mode
Leave editor without saving
Leave editor with saving
Unselect item
Add text or channel value
Add bitmap
Add bar graph
Open Online Help
Add LED
Delete
item
Add Analogue meter
Add
Multi-bitmap
Order in Z-position
Add
video
Add line, circle, rectangle
Copy
item

29. Process monitor
Active Process monitor

30. User administration 1
Click <Configuration>, <MCPS settings…>,
register card <Admin>
If ONE administrator-password is entered, the user administration is build and active.
Add up to three administrators.

31. User administration 3 Click <More Options>
Local, Network file based or Service based User Administration
Administrator Messages and
Active Directory based Login verification
Add up to three administrators.

32. User administration 4
Click <Configuration>, <MCPS settings…>,
register card <Users>
Add users and user groups to the user administration (Right click on <Users>)
Assign MCPS – rights to each user – What should the user be allowed to.
Make common settings/password settings for the user

33. User administration 5 Click <User login/password settings>
Assign a Login-name, a Login-ID and add a comment to the user.
Assign a password for the user to login.
Assign project access rights to the user
Select a duration for the password to be valid.