1. Compressor

2. Air Compressors
COMPRESSOR – A device which takes a definite quantity of fluid ( usually gas, and most often air ) and deliver it at a required pressure.
Air Compressor – 1) Takes in atmospheric air,
2) Compresses it, and
3) Delivers it to a storage vessel ( i.e. Reservoir ).
Compression requires Work to be done on the gas,
Compressor must be driven by some sort of Prime Mover ( i.e. Engine )

3. Classification Air Compressors Reciprocating Rotary Centrifugal
Single – stage
Multi - stage
No. of Stages
for Compression
No. of Sides of Piston
in operation
Single – acting
Double - Acting

4. Reciprocating Compressor - Working
2. Principle of Operation
Fig. shows single-acting piston actions in the cylinder of a reciprocating compressor.
The piston is driven by a crank shaft via a connecting rod.
At the top of the cylinder are a suction valve and a discharge valve.
A reciprocating compressor usually has two, three, four, or six cylinders in it.

5. Reciprocating Compressor - Working

6. Reciprocating Compressor – Equation for Work
Volume
Pressure P1 P2 V1 V2 3 2 2” 2’ 4 1
(Polytropic)
(Adiabatic)
(Isothermal)
Operations : 4 – 1 : Volume V1 of air aspirated into Compressor, at P1 and T1.
1 – 2 : Air compressed according to PVn = Const. from P1 to P2.
→ Temp increase from T1 to T2.
2 – 3 : Compressed air at P2 and V2 with temperature T2 is delivered.

7. Reciprocating Compressor – Equation for Work
During Compression, due to the excess temperature above surrounding, the air will exchange the heat to the surrounding.
Compression Index, n is always less than γ, the adiabatic index.
As Compressor is a work consuming device, every effort is desired to reduce the work.
Work done = Area under P-V curve
1 – 2” : Adiabatic Compression = Max. Work.
1 – 2 : Polytropic Compression
1 – 2’ : Isothermal Compression = Min. Work.

8. Reciprocating Compressor – Equation for Work
Thus, comparison between the Isothermal Work and the Actual Work is important.
Isothermal Efficiency, ηiso =
Isothermal Work
Actual Work
Thus, more the Isothermal Efficiency, more the actual compression approaches to the Isothermal Compression.
Actual Work = Wact = Area
Wact = Area (4-1) – Area (1-2) – Area (2-3) P1 P2 V1 V2 3 2 2” 2’ 4 1
(Polytropic)
(Adiabatic)
(Isothermal)

9. Reciprocating Compressor – Equation for WorkV1 V2 3 2 2” 2’ 4 1
(Polytropic)
(Adiabatic)
(Isothermal)
Now,

10. Reciprocating Compressor – Equation for WorkV1 V2 3 2 2” 2’ 4 1
(Polytropic)
(Adiabatic)
(Isothermal)
Delivery Temperature,
The solution of this equation is always negative.
This shows that Work is done ON the Compressor.

11. Reciprocating Compressor – Equation for Work
Clearance Volume :
Volume that remains inside the cylinder after the piston reaches the end of its inward stroke. P1 P2 V1 V4 6 2 5 1 3 4 V3
Effective Swept Volume, V1-V4
Swept Volume, V1-V3=Vs
Total Volume, V1
Clearance Volume,
V3=Vc
Thus, Effective Stroke Volume = V1 – V4
Actual Work = Wact = Area
Wact = Area ( ) – Area ( )

12. Reciprocating Compressor – Equation for WorkV1 V4 6 2 5 1 3 4 V3
Effective Swept Volume, V1-V4
Swept Volume, V1-V3=Vs
Total Volume, V1
Clearance Volume,
V3=Vc
But, P4 = P1 and P3 = P2

13. Reciprocating Compressor – Volumetric Efficiency
Ratio of free air delivered to the displacement of the compressor.
Ratio of Effective Swept Volume to Swept Volume. P1 P2 V1 V4 6 2 5 1 3 4 V3
Effective Swept Volume, V1-V4
Swept Volume, V1-V3=Vs
Total Volume, V1
Clearance Volume,
V3=Vc
Presence of Clearance Volume
Volumetric Efficiency less than 1. ( 60 – 85 % )
Volumetric Efficiency =
Effective Swept Volume
Swept Volume
V1 – V4
V1 – V3 =
Clearance Volume
Swept Volume
Clearance Ratio = Vc Vs =
= γ
( 4 – 10 % )

14. Reciprocating Compressor – Volumetric Efficiency
↑ Pr. Ratio ↑ Effect of Clearance Volume
….Clearance air expansion through greater volume before intake P1 P2 V1 V4 6 2 5 1 3 4 V3
Effective Swept Volume,
V1-V4
Swept Volume, V1-V3=Vs
Total Volume, V1
Clearance Volume,
V3=Vc
Cylinder bore and stroke is fixed.
Effective Swept Volume (V1 – V4) ↓ with ↑ Pr. Ratio
↓ Volumetric Efficiency

15. Reciprocating Compressor – Volumetric Efficiency6 2 5 1 3 4 V3
Effective Swept Volume,
V1-V4
Swept Volume, V1-V3=Vs
Total Volume, V1
Clearance Volume,
V3=Vc

16. Reciprocating Compressor – Actual P-V Diagram
: Theoretical P-V Diagram. P1 P2 2 1 3 4
Valve Bounce
Intake Depression
Atmospheric Pressure
Receiver Pressure
At 4, inlet valve does not open due to :
There must be a pressure difference across the valve to open.
Inlet valve inertia.
Pr. Drop continues till sufficient level for valve to force its seat.
Some valve bounce is set (wavy line).
Eventually, the pressure sets down at a level lower than atmospheric pressure. This negative pressure difference is known as Intake Depression.
Similar situation appears at 2, i.e. at the start of the delivery.
Pressure rise, followed by valve bounce and then pressure settles at a level higher than the delivery pressure level.
Air delivery to a tank / receiver, hence, generally known as Receiver Pressure.

17. Reciprocating Compressor – F.A.D.
Free Air Delivery (F.A.D.) : If the volume of the air compressor is reduced to atmospheric temperature and pressure, this volume of air is called FAD (m3/min)
Delivered mass of air = intake mass of air
If clearance volume is neglected
Where

18. Reciprocating Compressor – Multistage
High Pressure required by Single – Stage :
Requires heavy working parts.
Has to accommodate high pressure ratios.
Increased balancing problems.
High Torque fluctuations.
Requires heavy Flywheel installations.
This demands for MULTI – STAGING…!!

19. Reciprocating Compressor – Multistage
Series arrangement of cylinders, in which the compressed air from earlier cylinder (i.e. discharge) becomes the intake air for the next cylinder (i.e. inlet).
L.P. = Low Pressure
I.P. = Intermediate
Pressure
H.P. = High Pressure
L.P.
Cylinder
I.P.
H.P.
Intercooler
Air Intake
Air Delivery
Intercooler :
Compressed air is cooled
between cylinders.

20. Reciprocating Compressor – Multistage
Intake Pr.
P1 or Ps
Delivery Pr.
P3 or Pd 3 2 9 5 4 1 8 7 6
Intermediate Pr. P2
Without Intercooling
Perfect Intercooling
L.P.
H.P.
Volume
Overall Pr. Range : P1 – P3
Single – stage cycle :
Without Intercooling :
L.P. :
H.P. :
With Intercooling :
L.P. :
H.P. :
Perfect Intercooling : After initial compression in L.P. cylinder, air is cooled in the
Intercooler to its original temperature, before entering H.P. cylinder
i.e. T2 = T1 OR
Points 1 and 2 are on SAME Isothermal line.

21. Reciprocating Compressor – Multistage
Ideal Conditions for Multi – Stage Compressors :
A. Single – Stage Compressor : 3 2 9 5 4 1 8 7 6
L.P.
H.P.
Single – stage cycle :
Delivery Temperature,

22. Reciprocating Compressor – Multistage3 2 9 5 4 1 8 7 6
L.P.
H.P.
B. Two – Stage Compressor (Without Intercooling) :
Without Intercooling :
L.P. :
H.P. :
This is SAME as that of Work done in Single – Stage.
Delivery Temperature also remains SAME.
Without Intercooling

23. Reciprocating Compressor – Multistage3 2 9 5 4 1 8 7 6
L.P.
H.P.
C. Two – Stage Compressor (With Perfect Intercooling) :
With Intercooling :
L.P. :
H.P. :
Delivery Temperature,

24. Reciprocating Compressor – Multistage3 2 9 5 4 1 8 7 6
L.P.
H.P.
C. Two – Stage Compressor (With Perfect Intercooling) :
With Intercooling :
L.P. :
H.P. :
Now, T2 = T1
P2V2 = P1V1
Also P4 = P2
Shaded Area : Work Saving due to Intercooler…!!

25. Reciprocating Compressor – Multistage
Condition for Min. Work : 3 2 9 5 4 1 8 7 6
L.P.
H.P.
Intermediate Pr. P2 → P1 : Area → 0
Intermediate Pr. P2 → P3 : Area → 0
There is an Optimum P2 for which Area is maximum,
i.e. Work is minimum…!!
For min. Work,

26. Reciprocating Compressor – Multistage
Condition for Min. Work : 3 2 9 5 4 1 8 7 6
L.P.
H.P.

27. Reciprocating Compressor – Multistage
P2 obtained with this condition (Pr. Ratio per stage is equal) is the Ideal Intermediate Pr. Which, with Perfect Intercooling, gives Minimum Work, Wmin.
Equal Work per cylinder…!!

28. Reciprocating Compressor – Efficiency
Isothermal work done / cycle = Area of P – V Diagram
= P1V1 loge(P2/P1)
Isothermal Power = P1V1 loge(P2/P1) N
60 X 1000 kW
Indicated Power : Power obtained from the actual indicator card taken during a
test on the compressor.
Compressor Efficiency = Isothermal Power
Indicated Power
Isothermal Efficiency = Isothermal Power
Shaft Power
NOTE : Shaft Power = Brake Power required to drive the Compressor.

29. Reciprocating Compressor – Efficiency
Adiabatic Efficiency : Ratio of Power required to drive the Compressor; compared
with the area of the hypothetical Indicator Diagram; assuming
Adiabatic Compression.
Mechanical Efficiency : Ratio of mechanical output to mechanical input.
Mechanical Efficiency, ηmech = Indicated Power
Shaft Power

30. Reciprocating Compressor – Efficiency
How to Increase Isothermal Efficiency ?
Spray Injection : Assimilation of water into the compressor cylinder towards the
compression stroke.
Object is to cool the air for next operation.
Demerits : 1. Requires special gear for injection.
2. Injected water interferes with the cylinder lubrication.
3. Damage to cylinder walls and valves.
4. Water must be separated before delivery of air.
Water Jacketing : Circulating water around the cylinder to help for cooling the
air during compression.

31. Reciprocating Compressor – Efficiency
How to Increase Isothermal Efficiency ?
Inter – Cooling : For high speed and high Pr. Ratio compressors.
Compressed air from earlier stage is cooled to its original
temperature before passing it to the next stage.
D. External Fins : For small capacity compressors, fins on external surfaces are useful.
Cylinder Proportions : Short stroke and large bore provides much greater surface
for cooling.
Cylinder head surface is far more effective than barrel surface.

32. Reciprocating Compressor – Efficiency
Clearance Volume : Consists of two spaces.
1. Space between cylinder end & the piston to allow for wear.
2. Space for reception of valves.
High – class H.P. compressors : Clearance Vol. = 3 % of Swept Vol.
: Lead (Pb) fuse wire used to measure the gap between
cylinder end and piston.
Low – grade L.P. compressors : Clearance Vol. = 6 % of Swept Vol.
: Flattened ball of putty used to measure the gap
between cylinder end and piston.
Effect of Clearance Vol. :
Vol. taken in per stroke < Swept Vol. ↑ Size of compressor
↑ Power to drive compressor.

33. Reciprocating Compressor – Work Done
Assumption : Compression and Expansion follow same Law.
Work / cycle = Area P1 P2 V1 V4 6 2 5 1 3 4 V3
Effective Swept Volume,
V1-V4
Swept Volume, V1-V4=Vs
Total Volume, V1
Clearance Volume,
V3=Vc
P3 = P and P4 = P1

34. Reciprocating Compressor – Work Done
m1 is the actual mass of air delivered. P1 P2 V1 V4 6 2 5 1 3 4 V3
Effective Swept Volume,
V1-V4
Swept Volume, V1-V4=Vs
Total Volume, V1
Clearance Volume,
V3=Vc
Work done / kg of air delivered :