Presentation is loading. Please wait.

Presentation is loading. Please wait.

Eliminating one constraint for the scheduling committee Jay Benesch

Similar presentations


Presentation on theme: "Eliminating one constraint for the scheduling committee Jay Benesch"— Presentation transcript:

1 Eliminating one constraint for the scheduling committee Jay Benesch
A Wien for each beam Eliminating one constraint for the scheduling committee Jay Benesch

2 Idea The injector group within Accelerator Operations is working on a new front end with 200 keV gun and a new cryo-unit incorporating the capture. Reza Kazimi and I were chatting about it, discussing the problems caused by the pre-buncher between the two Wiens. Reza asked if one could build a minature Wien and install three in the chopper region. I decided to investigate. Current density required appeared too high, ~2500 A/cm2, for conventional conductor – until the YR burnt up. That runs at 3700 A/cm2 at 6 GeV, so it’s possible.

3 Present Wien Steel box with 5.375” inside width, 3.125” inside height. Nickel disk at each end to reduce field Z extent.

4 Field fall-off at end of Wien

5 Field integral comments
B is determined by precession desired. E is determined by need for straight orbit on axis. Calculated E value is 1.1% high for that required for x=0 at output mm square array shown below.

6 Chopping system Symmetric pair of transverse 499 MHz cavities and solenoids put the three bunches at 120o intervals on a 30 mm diameter circle. Moving slits may then independently reduce the current for each hall. Master slit has 24o apertures. 24o of 30mm circle is 6.3mm = width of beam between the slits and the de-chopping half of the system. Anything within the chopping system must have at least this aperture and have unity transfer matrix. -1 OK?

7 Basics of new Wiens Three osculating 26mm circles have their centers on a 30mm circle. There’s a stock metric steel tube size 26mm OD, 0.5mm wall – perfect for shielding one Wien from the next. E-field limit suggested 4 MV/m 200 keV beam, 110 degree precession capability needed For those values and sharp edged fields 30 cm long, BdL=5190 G-cm and EdL=108 (MV/m)*cm (3.6 MV/m). Since E field and B field don’t fall off the same way in Z, the electrode length has to be adjusted to minimize steering. For existing Wiens, the electrodes were chamfered to approximate the measured magnet fall-off.

8 End fields Electrode length was adjusted to match magnetic field fall-off. Magnetic shield length was varied in a failed attempt to adjust the B field end profile. Final electrode 14.8 cm half-length. Final steel tube 15cm half-length. x axis cm from center y axis V/cm or 208*G

9 Electrode curvature Flat electrodes provided less than a fourth the good field region needed for beam. I explored electrodes as arcs of circles, keeping 1cm spacing on mid-plane. 3cm chosen

10 Time delay as a function of precession
It was suggested this might be a problem. It isn’t.

11 single Wien model

12 conductor choice Some gap between the OD of the conductor and the steel desired to reduce field distortion. I chose 1mm initially. At least a 6.3mm square of good field region is needed for the chopped beam. The smaller the angle subtended by the dipole conductor, the better the field. I tried 15o, 12o and 10o . For this round of modeling, I used a square “helical end” coil built into Tosca, 3mm square, 15cm half-length. Hollow conductor may be fabricated in 10o wedge, mm2 , or 1/8” diameter refrigeration tubing used, 5.776mm2 of copper and 2630 A/cm2 in copper respectively, so start (end?) with tubing.

13 field quality from these choices
Dipole field +/- 0.6% over 6mm diameter circle Electric field +/- 1% over 6mm circle Beam propagation showed E field 0.2% high, but TOSCA lets one adjust this in the post-processor. Best E-field multiplier for central ray .9985; for 5.25mm square Plots will use .998*E for single and triple Wiens. Power supplies must be stable to better than 0.05% to avoid beam steering.

14 5.24 mm square array through Wien
Why 5.24 mm? A and C slit widths.

15 view showing horizontal focusing

16 A full length quad doesn’t help
A full length quad was added to the model in an attempt to counteract the horizontal focusing. Vertical focusing was so great as to preclude its use. Since it complicated the assembly and was no use, delete. Next two slides show the beam divergence in the XZ and YZ planes 10cm beyond the steel tube. Conclusion: either a quad doublet or quadruplet is needed after the Wien to make the unity transfer device needed inside the chopper for successful de-chopping. BTW, this design works nicely outside the chopper.

17 YZ projection 10cm downstream

18 XZ projection 10cm downstream

19 Is the magnetic shield adequate?
Model was copied twice with offsets to create a larger model with three Wiens on 30mm diameter chopping circle. E and B fields are identical in the three Wiens Stray field effects are seen and are small – the 5.24mm square arrays still get through all Wiens. Flipping the field in the bottom Wien (hall B) doesn’t change the result. Conclusion: shield is good enough for this first order model.

20 Three Wien filters on 30mm circle

21 Three Wiens Z+ end view 16 rays on 5.24mm square in each bore

22 E field map superimposed on orbits

23 Next steps Obtain endorsement from Division management so I can get formal help from CASA and EGG. Or stop. Further explore parameter space in attempt to increase good transmission region: electrode curvature in mm increments, dipole coil inner radius in 100 mm increments Add quadruplet (quads and correctors) after Wien to allow full transfer matrix to be set to unity, or at least no more than swapping head and tail of bunch. Model chopping system with included Wien system. Use round conductors with leads in dipole to learn how this affects transmission. If all goes well, engineering design/fab of prototype. EGG test in injector stand.


Download ppt "Eliminating one constraint for the scheduling committee Jay Benesch"

Similar presentations


Ads by Google