1. Crane Fundamentals Lifting Safety BY - ALEX MATHEW HSE ENGINEER LAHOUD ENGINEERING CO

3. Terminologies

4. Working Radius The load radius is the distance measured from the centre of the rotation of the crane (centre pin) to the load hook (centre of gravity of the load) while the boom is loaded. The working radius can also be effected by the load swinging outside of the load radius. At all time ensure the hook is positioned directly below the leading sheave and the crane’s hook does not have to swing of out of its naturel fall to attach to the load.

5. OUTRIGGERS

6. SOFT FOOTINGS Load chart ratings are only applied when the ground conditions are firm enough to support the crane and keep it level during the lift. If the ground is soft or unstable, the tyres or outriggers will sink or subside causing the loss of capacity in all cases, heavy duty blocking having a large bearing area will be necessary to prevent sinking and provide a solid base for the crane.

7. CRANE POSITIONING Boom length, working radius, outrigger setup and the correct positioning of a crane will determine the outcomes of a lift.

8. Rigging Equipment Slings Types of slings covered are those made from alloy steel chain, wire rope, metal mesh, natural or synthetic fiber rope, and synthetic web. ChainWire ropeMetal meshSynthetic

9. Sling Inspection Inspect slings:  Each day before use  Where service conditions warrant Remove them from service if damaged or defective

10. Remove From Service Immediately remove damaged or defective slings from service

11. Adapts to shape of the load Can damage by sudden shocks Best choice for hoisting very hot materials Must have an affixed tag stating size, grade, rated capacity, and sling manufacturer Alloy Steel Chains

12. Markings Alloy Steel Chain It must be marked with grade or manufacturer's mark

13. Hooks, rings, oblong links, or other attachments, when used with alloy steel chains, must have a rated capacity at least equal to that of the chain Alloy Steel Chain Attachments Rated Capacity

14. Job or shop hooks and links, or makeshift fasteners, formed from bolts, rods, etc., or other such attachments, CANNOT be used Unsuitable Alloy Steel Chain Attachments RightWrong

15. Chain Wear When a chain shows excessive wear, or is cracked or pitted, remove it from service Non-alloy repair links can not be used

16. RIGGING OPERATION SERIES

17. Wire Rope Slings Eye Splices Eye splices made in any wire rope Eye splices made in any wire rope must have at least three full tucks must have at least three full tucks

18. Cover or blunt protruding ends of strands Protruding Ends

19. Wire Rope Clips When using U-bolt wire rope clips to form eyes, ensure the "U" section is in contact with the dead end of the rope This is the correct method Dead End

20. Wire Rope Slings Remove From Service If these happen, remove the wire rope sling from service Crushing Kinking Bird Caging Kinking

21. Mark or code to show: Mark or code to show: Name or trademark of manufacturer Name or trademark of manufacturer Rated capacities for the type of hitch Rated capacities for the type of hitch Type of material Type of material Synthetic Web Sling Markings

22. Fittings must be: Fittings must be: At least as strong as that of the sling At least as strong as that of the sling Free of sharp edges that could damage the webbing Free of sharp edges that could damage the webbing Synthetic Web Slings Fittings

23. Stitching is the only method allowed to attach end fittings to webbing, or to form eyes Synthetic Web Sling Stitching Stitching

24. Remove from service if any of these are present: Remove from service if any of these are present: Acid or caustic burns Acid or caustic burns Melting or charring of any part Melting or charring of any part Snags, punctures, tears or cuts Snags, punctures, tears or cuts Broken or worn stitches Broken or worn stitches Distortion of fittings Distortion of fittings Synthetic Web Slings Remove from Service Heat Damage

25. RIGGING OPERATION SERIES SAFE WORKING LOAD Rule of Thumb of Computing Rope S.W.L. S.W.L. = Rope Diameter x Rope Diameter x 8 EXAMPLE: (a) 1/2 inch diameter rope SWL = 1/2 x 1/2 x 8 = 2 tons SWL = 1/2 x 1/2 x 8 = 2 tons (b) 5/8 inch diameter rope SWL = 5/8 x 5/8 x 8 = 3.125 tons SWL = 5/8 x 5/8 x 8 = 3.125 tons (c) I inch diameter rope SWL = 1 x 1 x 8 = 8 tons SWL = 1 x 1 x 8 = 8 tons

26. Unsafe Act/Condition A

27. B

28. C

29. D

30. E

31. F

32. G

33. Thank You