Design & boclair academy OBLIQUE VIEWS.

Slides:



Advertisements
Similar presentations
Oblique and Isometric Drawings
Advertisements

Technical Sketching and Drawing
Graphic Communication
Chapter 5 Pictorial Sketching.
Shawlands Academy Department Of Technical Education
Graphic Communication.  Isometric Views are one of the forms of 3D views that you need to know about in the Standard Grade Graphic Communication course.
OBLIQUE VIEWS Oblique drawings provide a quick way to sketch an object and represent the three dimensions of height, width and depth. Oblique drawings.
AUXILIARY ELEVATION.
Graphic Communication.  The elevation and plan of an angled bearing block are shown.  Project an auxiliary elevation in the position indicated Auxiliary.
Isometric and Oblique Pictorials
Freehand Sketching.
CE En 112 Engineering Drawing with CAD Application
CE En 112 Engineering Drawing with CAD Application
1 Chapter 6 – Pictorial Sketching Print handouts Select File, Print Edit the following selections to read: Select the OK button.
Hexagons & Hexagonal Prisms. Hexagons Hexagons are 6 sided shapes. Hexagons can be dimensioned in 2 different ways. 1. Across the faces. 2. Across the.
Aberdeen Grammar School Isometric Views. Isometric Drawings Lengths and breadths are drawn at 30° to the horizontal. Heights are drawn vertically. All.
Pyramid Construction Pyramids Square Rectangle Hex Cone.
3rd Angle Orthographic Projection
Graphic Communication
Isometric Drawing - Trammel Method
Square Pyramid (cut). Cut Square Pyramid - Problem The given views show the Front Elevation and unfinished Plan of a cut square pyramid. Draw the following.
Greenfaulds High School Orthographic Views. Orthographic Projection Orthographic projection is the name given to the type of drawing where a 3D object.
Graphic Communication.  Oblique views are one of the forms of 3D views that you need to know about in the Standard Grade Graphic Communication course.
Graphic Communication
17/02/03Designed by Barry Forbes Graphic Communication Hexagons & Hexagonal Prisms.
Graphic st aidans high ISOMETRIC CIRCLES.
Graphic Communication
Graphic st aidans high AUXILIARY PLAN.
Design & boclair academy ISOMETRIC CIRCLES.
Cut Cones. At the end of this unit you will be able to: Identify a Cone and draw orthographic views of Cones with cut surfaces. Project a cut surface.
Auxiliary Plan Two views of a coat hook are shown below. The coat hook is made from Ø40mm aluminium bar and is fixed to the wall through a Ø4mm hole.
Hexagons & Hexagonal Prisms.
Design and technology st aidan’s high A pictorial sketch of a wall lamp is shown. The shade is in the form of a cut cone. Draw, from the given.
Menu Cones Cones – What Are They?. Menu Cones Drawing an Orthographic Cone You will be given sheets that will have the following views of a cone. These.
Design & boclair academy OBLIQUE VIEWS.
Aberdeen Grammar School. Oblique Projection Oblique views are one of the forms of 3D views that you need to know about in the Standard Grade Graphic Communication.
Oblique Projections Oblique Projections.
Isometric Views.  Lengths and breadths are drawn at 30° to the horizontal.  Heights are drawn vertically.  All sizes are drawn to their exact sizes.
Greenfaulds High School Oblique Views. Oblique views are a type of pictorial view. They show an object from the front with all depths at an angle of 45°.
Oblique Views. Oblique Projection The given views show the orthographic views of a mantle clock. Draw an oblique view with corner X in the given position.
Oblique Pictorials Get out your notebooks. 2.1 Oblique Pictorials.
ENGINEERING DRAWING VISUALIZATION. Axonometric & Oblique Projection.
OBLIQUE VIEWS. Oblique Projection Oblique views are one of the forms of 3D views that you need to know about in the Standard Grade Graphic Communication.
Graphic st aidans high OBLIQUE VIEWS.
CLASS 7 Review: Axonometric/Oblique Projections Isometric Projection
Graphic st aidans high OBLIQUE VIEWS.
1 SheetCourse: Engineering Graphics 1504Memorial University of Newfoundland Engineering Graphics 1504 Lecture 2 – General Sketching Objectives l Lines.
GE1021 Engineering Drawing and Graphics
Isometric and Oblique Pictorials
Deans Community High School
Graphic Communication
Introduction to Oblique
CLASS 7 Review: Axonometric/Oblique Projections Isometric Projection
Graphic Communication
Axonometric drawings BDU
Isometric and Oblique Pictorials
Isometric and Oblique Pictorials
Types of pictorial projection
Graphic Communication
Cut Hexagonal Prism Cut Hexagonal Prism - Question
Isometric and Oblique Pictorials
Chapter 5 Isometric Sketching.
Graphic Communication
Graphic Communication
Review: Axonometric/Oblique Projections Isometric Projection
Graphic Communication
Graphic Communication
Chapter 5 Isometric Sketching.
The elevation and plan of an angled bearing block are shown.
Presentation transcript:

design & boclair academy OBLIQUE VIEWS

design & boclair academy Oblique Projection The given views show the orthographic views of a mantle clock. Draw an oblique view with corner X in the given position. Do not add the hands of the clock to your drawing. X X X

design & boclair academy Drawing Oblique Crate Start the oblique view by drawing a crate to fit the clock into. X X X For Standard Grade drawings the depth of the crate should be drawn at 45 o with the size measured at either full size or half full size. In this case half sizes have been used. In this case the size of the crate will enclose the body of the clock but does not include the clock face. This will be added to the main drawing later.

design & boclair academy Drawing Clock Top Draw the top curve of the clock body on the front surface of the crate. X X X Draw a 45 o line through each centre to find the tangent points where the curves are joined by straight edges. Project the centre of the curve back at 45 o to locate the centre of the back curve.

design & boclair academy Drawing Clock Face Draw the circle for the face on the front surface of the clock body. X X X Locate the centre of the clock face at the very front of the drawing. Remember that the distance in this drawing is half of the full size. Draw the outside circle and the inside circle of the clock face. Locate the tangent points on the face circles and add the straight edges required.

design & boclair academy Drawing Clock Base Add the feet details to the drawing. Remember to use half sizes for any dimensions which are measured along 45 o lines. X X X

design & boclair academy Finishing Drawing To finish the drawing, darken in the outlines of the oblique view. X X X

design & boclair academy Alternative Oblique View At Standard Grade an Oblique View may be drawn with the dimensions on the 45 o angles at full size or half full size. The two drawings shown here show the different views generated by both methods. X Oblique view using full sizes (Cavalier Projection) X Oblique view using half full sizes (Cabinet Projection)

design & boclair academy OBLIQUE VIEWS finished back to menu