Fuel and DCR Overview Copyright 2011 VeriFone, Inc. All rights reserved. No part of this publication may be copied, distributed, stored in a retrieval system, translated into any human or computer language, transmitted in any form or by any means, without the prior written consent of VeriFone, Inc. VeriFone, Inc. is a registered trademark of VeriFone, Inc. All other brand names and trademarks appearing in this documentation are the property of their respective owners. Introduction Page With Picture: Use Arial, 125 pt for title, Use Arial, 100 pt for introduction. This page will again display the title as well as give an introduction to the presentation. A good way to do this is to give an example of why the subject is important, what’s in it for the student. Let’s say the training module is how to program the date and time on the terminal. An introduction could be: Jane is the manager of a convenience store. She has noticed on her receipts the time is incorrect. She needs to know how to update the time in her terminal.

Introduction Fuel and DCR Overview As a VASC, it will be critical for you to be able to determine the type of fuel and dispenser card readers (DCRs) which interface with the Ruby system. Each dispenser manufacturer has specific equipment which must be used in order to successfully interface with the Ruby system. Failure to understand the equipment and interfaces will result in non-communication with the dispensers and card readers. Introduction Page With Picture: Use Arial, 125 pt for title, Use Arial, 100 pt for introduction. This page will again display the title as well as give an introduction to the presentation. A good way to do this is to give an example of why the subject is important, what’s in it for the student. Let’s say the training module is how to program the date and time on the terminal. An introduction could be: Jane is the manager of a convenience store. She has noticed on her receipts the time is incorrect. She needs to know how to update the time in her terminal.

Objectives In this module you will learn: Fuel and DCR Overview Dispenser interfaces compatible with the Ruby system. Required equipment when interfacing fuel and card readers with Ruby system. Different types of blend dispensers Suggested reading. Objective List Page With Picture: Use Arial 125 pt, for Objective, Use 100 pt. For words A training objective is an action you promise the student he/she will be able to perform after they complete a training module. A training objective should be specific. Examples: * Open an application using GemStall. * Program the Time and Date on the Terminal The following are NOT training objectives: Become familiar with gemstall. (Becoming familiar is not an action) Learn the maintenance mode. (Not specific – too vague) NOTE: The training modules are to be “bite sized” – meaning approximately 20 minutes of material. You should not have more than 3 objectives, if you have more to cover break up the training into smaller pieces of information.

Interfaces Fuel and DCR Overview The VeriFone POS system is capable of interfacing with the following dispenser manufacturers: Bennett Gilbarco Schlumberger Tokheim Wayne Each network or major oil (Alliance Data Systems, Citgo, Shell, etc.) has specific standards as to which pump manufacturers will be supported. Release Notes will serve as an excellent tool to ensure a dispenser is compatible and the appropriate firmware needed when interfacing with the Ruby Controller. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview VeriFone POS Controller Fuel & DCR Interface When interfacing fuel and card readers with Ruby system, an RS232 serial connection will be used. The maximum length for an RS232 connection from the Ruby Controller to the fuel and the card reader interfaces is 100 feet. However, for DCRs a CAT Board (Wayne) or B&B Converter can be used to change the protocol from RS232 to RS485 which allows serial communication up to 4000 ft. Please note spliced cables should never be used. RS232 – Maximum: 100 ft. (DCRs) with CAT /B&B: 4000 feet Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Release Notes When interfacing the Dispenser and DCR devices with Ruby system it will be critical to refer to the Release Notes for the specific software application and version. The release notes include a Fuel Hardware Peripherals chart. Prior to installing and upgrading VeriFone software refer to these charts. The chart will determine what version of firmware is required for the Dispenser and DCR devices in order to successfully interface with a Ruby system. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Gilbarco – PAM 1000 The Gilbarco fuel interface is referred to as the PAM or Pump Access Module. When interfacing fuel with the Ruby controller please note the baud rate in the PAM must be set to 4800. The cable and connector needed for the PAM are: RS232 Cable (up to 100 feet): P/N 13836-xx Adapter, DB9 PAM: P/N 13652-01 The Gilbarco Adapter (P/N 13652-01) connects to the Gilbarco fuel interface port labeled P909-2 on the PAM unit. The default fuel comport on the Ruby controller is usually comport 6. PAM adaptor – 13652-01 connection There will be an RS232 connected to this adaptor and then connected to comport 6 on the Ruby Controller. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Gilbarco – Enhanced PAM There is also an Enhanced PAM. The main difference between a PAM and an Enhanced PAM is the firmware. An Enhanced PAM will have firmware v32.1.60 or higher. Cable and connection part numbers are the same for the PAM as the Enhanced PAM. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Gilbarco – Pam 5000 Gilbarco has released the PAM 5000. This Pump Access Module (PAM) controls BOTH fuel and DCRs in one unit.  The PAM 5000 brings the following new capabilities: -- PAM 5000 is a functional drop-in replacement for PAM 1000 with no POS software changes required. -- The two-wire cables used for pump control can be connected directly to the DSB492 Current Loop module in the PAM 5000, eliminating the PA0261 distribution box that is normally used for pump control. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Gilbarco – CRIND The Gilbarco card reader interface is referred to as the CRIND or Card Reader IN Dispenser. When interfacing card readers with the Ruby controller please note the baud rate in the PAM must be set to 4800. CRIND addresses must match the fueling point addresses. If these are not set up the same there will be communication problems. The CRIND requires Gilbarco Generic CRIND software. Major Oil CRIND (MOC) software is not compatible with VeriFone DCR software. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Gilbarco – CRIND The following parts are needed to establish communication between the Gilbarco CRIND (D-Box) and the Ruby Controller: RS232 Cable: P/N 13836-25 Male DB25 Adapter: P/N 13542-01 DCR Converter: P/N 13976-01 Gilbarco DCR Distribution Cable: P/N 13870-01 RS232 Cable DB25 Adaptor B & B Connector Distribution Cable Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Gilbarco - CRIND The RS232 cable is connected to the appropriate comport on the Ruby Controller. The default card reader comport on the Ruby controller is usually comport 9. The RS232 is connected to the male adapter. The male adapter is connected to the B & B/DCR Converter. The B & B is connected to the Gilbarco DCR Distribution Cable. RS232 Cable DB25 Adaptor B & B Connector DCR Distribution Cable Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Gilbarco – CRIND The DCR Converter (B & B) converts an RS485 communication to RS232. Ensure the correct dip-switch is set on the DCR converter. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Gilbarco – GSM Should a Gilbarco site need debit capabilities a Gilbarco Security Module (GSM) will be required. The GSM is attached to the Ruby controller via an RS232 interface. The GSM is an encryption/decryption device that ensures debit card, PIN, and other critical customer information is maintained under the most secure conditions. This is only required for debit handling networks. The GSM version is dependent on the network. Any open comport can be used on the Ruby Controller – except for comports 2 & 3. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Gilbarco – GSM The GSM is a Gilbarco part and must be ordered through Gilbarco. When receiving the GSM you will be shipped a gray connector. When interfacing a GSM with a Ruby controller, do not use the gray connector. When interfacing a GSM with a Ruby controller you will need VeriFone P/N 55028-01, Rev D. This MUST be used to successfully connect the GSM with the Ruby controller. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Schlumberger - Fuel The Schlumberger fuel interface is referred to as the SAM or Schlumberger Access Module. Several years ago Tokheim purchased Schlumberger. For this reason the interface box may be referred to as a TAM or Tokheim Access Module. Please be aware the internal electronics and port connections are identical to the SAM. When interfacing fuel with the Ruby controller please note the baud rate in the S/TAM must be set to 4800. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Schlumberger - Fuel The cable and connector needed for the S/TAM are: RS232 Cable: P/N 13836-xx Adaptor, SAM: P/N 55036-01 The DB9 male adapter (P/N 55036-01) connects to Port 1 on the S/TAM. After the connection is made the adapter should be secured by tightening the screws. The RS232 cable is then connected from the adapter to the appropriate port assigned on the Ruby controller. The default fuel comport on the Ruby controller is usually comport 6. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining. Fuel Connection

Interfaces Fuel and DCR Overview Schlumberger – CardScan The card reader interface for Schlumberger is also the S/TAM. Schlumberger card readers are referred to as CardScan. When interfacing card readers with the Ruby controller please note the baud rate for the S/TAM CardScan must be set to 4800. The default card reader comport on the Ruby controller is usually comport 9. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining. CardScan Connection D-Box Connection

Interfaces Fuel and DCR Overview Schlumberger – CardScan The following parts are needed to establish communication between the Schlumberger CardScan and the Ruby controller. RS232 Cable: P/N 13836-xx DB9 Adapter: P/N 55036-01 Note when interfacing Schlumberger card readers with the Ruby controller a DCR Converter (B & B is not required). Connect the RS232 cable (P/N 13836-xx) to the appropriate comport on the Ruby controller and to the male DB9 Adapter (P/N 55036-01). The 9-pin adapter connects to Port 2 on the S/TAM. Fuel Connection Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining. CardScan Connection D-Box Connection

Interfaces Fuel and DCR Overview Tokheim - Fuel Closed Box The Tokheim fuel interface is referred to as the VXDHC. DHC is an acronym for Dedicated Hose Controller. Prior to the VXDHC Tokheim manufactured a DHC interface. The main difference between a DHC and a VXDHC is the firmware. A VXDHC will have firmware v4200.03.09 or higher. Cable and connection part numbers are the same for the DHC as the VXDHC. Label Close-up VXDHC Inside Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Closed Box When interfacing fuel with the Ruby Controller please note the baud rate in the DHC must be set to 9600. The cable and connector needed for the VXDHC are: RS232 Cable (up to 100 feet): P/N 13836-xx Adapter, DB25M Null Modem: P/N 13581-01 The Tokheim adapter (P/N 13581-01) connects to the DHC J4 connector. After the connection is made the adapter should be secured by tightening the screws. The RS232 cable is then connected from the adapter to the appropriate port assigned on the Ruby Controller. The default fuel comport on the Ruby Controller is usually comport 6. Label Close-up VXDHC Inside Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Tokheim – DPT The Tokheim card reader interface is referred to as the DPT or Dispenser Payment Terminal. When interfacing card readers with the Ruby Controller please note the baud rate for the DPT must be set to 9600. DPT addresses must match the fueling point addresses. If these are not set up the same there will be communication problems. RS232 Cable DB25 Adaptor B & B Connector DCR Distribution Cable Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Tokheim – DPT The following parts are needed to establish communication between the Tokheim DPT and the Ruby Controller: RS232 Cable: P/N 13836-xx Male DB25 Adapter: P/N 13542-01 DCR Converter: P/N 13976-01 Tokheim DCR Distribution Cable: P/N 13871-01 RS232 Cable DB25 Adaptor B & B Connector DCR Distribution Cable Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Tokheim - DPT The RS232 cable is connected to the appropriate comport on the Ruby Controller. The default card reader comport on the Ruby Controller is usually comport 9. The RS232 is connected to the male adapter. The male adapter is connected to the B & B/DCR Converter. The B & B is connected to the Tokheim DCR Distribution Cable. RS232 Cable DB25 Adaptor B & B Connector DCR Distribution Cable Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Tokheim – DPT The DCR Converter (B & B) converts an RS485 communication to RS232. Ensure the correct dip-switch is set on the DCR converter. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Wayne - Fuel The Wayne fuel interface is referred to as the PIB or Pump Interface Board. When interfacing fuel with the Ruby Controller please note the baud rate in the PIB must be set to 1200. The cable and connector needed for the PIB are: RS232 Cable (up to 100 feet): P/N 13836-xx Adapter, DB25 Null Modem: P/N 13642-01 Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining. Fuel Connection PIB Board

Interfaces Fuel and DCR Overview Wayne – PIB The Wayne Adapter (P/N 13642-01) connects to the Wayne PIB interface port. After the connection is made the adapter should be secured by tightening the screws. The RS232 cable is then connected from the adapter to the appropriate port assigned on the Ruby Controller. The default fuel comport on the Ruby Controller is usually comport 6. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining. Fuel Connection PIB Board

Interfaces Fuel and DCR Overview Wayne - HyperPIB There is also a Hyper-PIB. The Hyper-PIB is a different electronic board and uses a different firmware version. Cable and connection part numbers are the same for the PIB as the Hyper-PIB. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Wayne – DCPT The Wayne card reader interface is referred to as the DCPT or Dispenser Card Payment Terminal. When interfacing card readers with the Ruby Controller please note the baud rate for the DCPT must be set to 9600. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining. DCPT Connection CAT Board

Interfaces Fuel and DCR Overview Wayne – DCPT There are two communication hardware options for installation when interfacing Wayne DCPT’s with the Ruby Controller. They are: Installation of the CAT (Card Access Terminal) board, or Cable/adapter connections using the DCR Converter (B & B Connector) Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining. DCPT Connection CAT Board

Interfaces Fuel and DCR Overview Wayne – DCPT, Using B & B/DCR Converter The following parts are needed to establish communication between the Wayne DCPT and the Ruby Controller when installed with the DCR Converter: RS232 Cable: P/N 13836-xx Male DB25 Adapter: P/N 13542-01 DCR Converter: P/N 13976-01 Wayne DCR Distribution Cable: P/N 13824-01 RS232 Cable DB25 Adaptor B & B Connector DCR Distribution Cable Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Wayne – DCPT, Using B & B/DCR Converter The RS232 cable is connected to the appropriate comport on the Ruby Controller. The default card reader comport on the Ruby Controller is usually comport 9. The RS232 is connected to the male adapter. The male adapter is connected to the B & B/DCR Converter. The B & B is connected to the Wayne DCR Distribution Cable. RS232 Cable DB25 Adaptor B & B Connector DCR Distribution Cable Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Wayne – DCPT, Using CAT Board The following parts are needed to establish communication between the Wayne DCPT and the Ruby (Controller) when installed with the CAT Board: RS232 Cable: P/N 13836-xx Male DB25 Adapter: P/N 13524-01 Connect the RS232 cable (P/N: 13836-25) to the appropriate comport on the Ruby Controller and to the male DB25 adapter (P/N: 13542-01). The male adapter is connected to the CAT Board serial connection. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining. DCPT Connection CAT Board

Interfaces Fuel and DCR Overview Bennett - Fuel The Bennett fuel interface is referred to as the 515 Pump Controller. A 515 Pump Controller will have firmware v5.05; 515 firmware is expected to be backward compatible with this certified version. The 515 Interface is valid for VeriFone applications supporting base 148 or higher. When interfacing fuel with the Ruby controller, the BAUD rate for the 515 is automatically set to 9600. Verify that the Ruby Controller is also set at 9600 for fuel communication. Communication Port 1 on the 515 Pump Controller is set for fuel communication from the Ruby Controller. The cable and connector needed for the 515 are: • RS232 Cable 13836-XX (specify length needed) • DB9 Male Adapter 105471 – 1 is supplied with each 515 The default fuel comport on the Ruby Controller is usually comport 6. 515 adaptor – 105471 connection There will be an RS232 connected to this adaptor and then connected to comport 6 on the Ruby Controller. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Interfaces Fuel and DCR Overview Bennett – DCT Bennett refers to the Dispenser Card Reader as the DCT or Debit Card Terminal. Bennett utilizes the VeriFone Secure PumpPAY (MX760) for Pacific dispensers for outside debit and credit transactions. VeriFone’s Secure PumpPAY features a direct communication connection to the Ruby Controller. Bennett Pacific Dispensers utilize a 3 wire connection (RS485) to the B&B converter; which is then connected to port 9 on the Ruby Controller. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining. Bennett utilizes the Secure PumpPAY (MX760) for credit and debit transactions

Blend Types Fuel and DCR Overview All locations will need to determine if they will be blending specific grades of fuel. Blending versus non-blending affects the number of fuel tanks and the type of dispensers at the site. When a location does not blend fuel the site will have a physical tank for each fuel product or grade. Tanks are expensive and use a great deal of physical space - for this reason many sites will choose to blend specific fuel products saving money and real-estate. When a site decides to blend fuel products the piping from the tanks to the dispensers is different. Typically if a site is blending fuel they are blending Unlead fuel with Premium to make a Mid-Grade product. The percentage of octane is determined by the amount of Unlead and Premium. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Blend Types Fuel and DCR Overview Premium fuel has more octane than Unlead. Premium is sometimes referred to as High Feedstock and Unlead is referred to as Low Feedstock. When blending fuel the more Premium or High Feedstock, the more octane the Mid-Grade will have. Dispensers that blend product are physically different than dispensers that do not blend products. There are different blend dispenser types. When interfacing blend dispensers with the Ruby Controller it will be important to know the way in which the dispenser is physically blending products. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Blend Types Fuel and DCR Overview When interfacing blend dispensers with the Ruby Controller, there are four different dispenser blend types you will need to understand. They include: Fixed Electronic Variable Mechanical A blend dispenser will be physically manufactured and defined by each specific pump manufacturer. Let’s take a closer look at each dispenser blend type. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Blend Types Fuel and DCR Overview Fixed When a blend dispenser is defined as fixed by the manufacturer then the blend ratio in the dispenser CANNOT be changed. The POS controller will be programmed with blend ratio’s but it will not be sent to the dispenser. However, the POS controller must be programmed to match the blend ratio in the dispenser – otherwise reporting on the POS will be inconsistent. In order to comply with weights and measurers dispensers should be programmed both at the dispenser and on the POS controller and MUST match. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Blend Types Fuel and DCR Overview Electronic When a blend dispenser is defined as electronic by the manufacturer. An ASR can change the programming in the dispenser. The POS controller will be programmed with blend ratio’s and these ratio’s are usually sent to the dispenser. The blend programming in the dispenser MUST match the blend programming on the POS controller. If the blend programming in the dispenser does not match the POS there will be communication and blending problems. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Blend Types Fuel and DCR Overview Variable When a blend dispenser is defined as variable by the manufacturer. An ASR can change the programming in the dispenser. The POS controller will be programmed with blend ratio’s and may trump any blend programming in the dispenser. The blend programming in the dispenser MUST match the blend programming on the POS controller. If the blend programming in the dispenser does not match the POS there will be communication and blending problems. Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Blend Types Fuel and DCR Overview Mechanical Mechanical Blender Mechanical Blender are located inside the dispenser and blend fuel prior to the metering process. Older Tokheim and Wayne dispensers utilized the Mechanical Blender. Gilbarco does offer a mechanical blend kit to install in there older dispensers. Basically, a Mechanical Blender sits under the dispenser in the piping area where the blend valve is piped to the middle product (Midgrade) and the left and right sides to the unleaded and premium products. There is a disk with a pre-determined hole drilled in the center and this determines what your blend ratio is. This is called an orifice. If you need to change the blend ratio, you need to remove the existing disks and replace them with new ones. You can turn any three product dispenser into a mechanical blender as long as the dispenser is not a blender by factory default. Mechanical Blender Objective or Contents Page With Picture: Use Arial 125pt for the title of objective, use Arial 100pt for the explanation. Use these pages to explain and discuss the objective. Left hand side is for pictures, graphics, charts, etc which give examples of what it is you are explaining.

Suggested Reading Fuel and DCR Overview To review the concepts presented in this training module we recommend referring to the following documentation: Pump Interface Diagram – this is available in the VASC Service Manual under Ruby Documentation, Ruby School Handouts; also located in the Training Materials link at the top and is labeled “Fuel-DCR Interface Diagram”. Fuel and DCR Interfaces and Programming Reference Guide - this is available in the VASC Service Manual when accessing the Peripherals hyperlink. Release Notes – Fuel Hardware Peripherals chart Review Page With Picture: Use Arial 125 pt, for Review, Use 100 pt. For words The review page should be used if this is a continuation from a previous training module, in order to prepare the student for the next part or section of the training. It should be used at the end of the training module to review the training objectives with the student.

Fuel and DCR Overview Congratulations! You’ve completed the Fuel & DCR Overview. Thank you for using VeriFone Academy for your training needs Introduction Page With Picture: Use Arial, 125 pt for title, Use Arial, 100 pt for introduction. This page will again display the title as well as give an introduction to the presentation. A good way to do this is to give an example of why the subject is important, what’s in it for the student. Let’s say the training module is how to program the date and time on the terminal. An introduction could be: Jane is the manager of a convenience store. She has noticed on her receipts the time is incorrect. She needs to know how to update the time in her terminal.