© 2012 Delmar, Cengage Learning Chapter 14 HAZWOPER

© 2012 Delmar, Cengage Learning Fall Protection Fall protection is a standard designed to reduce or eliminate injuries from falls. The standard requires fall protection to be used when a technician needs access, movement, or works at an elevation of 6 feet or higher.

© 2012 Delmar, Cengage Learning Figure 14-2 HAZWOPER

© 2012 Delmar, Cengage Learning Hoisting Equipment Hoisting systems are used to safely raise, lower, and move loads that are too heavy to moved manually. The most difficult aspect of the job is estimating the load. Loads should be suspended no longer than necessary.

© 2012 Delmar, Cengage Learning HAZWOPER is categorized as follows: Emergency Response – first responder awareness level, first responder operation level, and hazardous materials technicians and specialist level Hazardous Waste Operations – Incident command system, scene safety and control, spill control and containment, decontamination procedures, emergency termination, or all clear Hazard Protection, Prevention and Control – terms and definitions, PPE levels, identifying hazardous materials and hazards initiating an emergency response, avoiding hazards, entry of hazardous materials into the human body, and use of field monitors and field survey instruments

© 2012 Delmar, Cengage Learning The HAZWOPER standard defines five levels for emergency responders First responder – awareness level First responder – operations level Hazardous materials technician level Hazardous material specialist On-scene incident commander

© 2012 Delmar, Cengage Learning First Responder – Awareness Level The first responder – awareness level is directed at individuals who witness or discover a hazardous chemical release and who have received emergency response training.

© 2012 Delmar, Cengage Learning First Responder – Operations Level When a hazardous chemical release occurs, the process technicians working on the unit specific to the release will attempt to respond. It is virtually impossible to pull a highly trained emergency response team who would know the unit a fraction as well as the technicians.

© 2012 Delmar, Cengage Learning Emergency Response Emergency response is defined as a loss of containment of a chemical or the potential for loss of containment that results in an emergency response situation requiring an immediate response. Emergency response procedures are applied to every individual working for a company.

© 2012 Delmar, Cengage Learning Hazardous Waste Operations Hazardous waste operations in the CPI involve the use of a complex incident command system. The ICS coordinates all emergency response activity. Hazardous waste operations are classified into three categories: Small hazards Medium-sized hazards Large hazards

© 2012 Delmar, Cengage Learning Scene Safety and Control Hot zone - the area around the incident where contamination has occurred. Warm zone – used to decontaminate technicians leaving the hot zone. Cold zone – a staging area where the incident command post is established.

© 2012 Delmar, Cengage Learning Figure 14-3 Scene Safety and Control

© 2012 Delmar, Cengage Learning Spill Control and Containment Absorbents, adsorbents, curbing and diking, segregated sewers, earthen dams, and fire monitors are devices used to control chemical spills and releases.

© 2012 Delmar, Cengage Learning Decontamination Procedures In a decontamination procedure, anything that comes into contact with a hazardous chemical is neutralized in the warm zone.

© 2012 Delmar, Cengage Learning Hazard Identification During a chemical release the identification of the material is important, the following procedures must be completed quickly and from a safe distance: –Determine the location of the release. –Analyze the composition of the material. –Identify other characteristics. –Report and discuss with area technicians and supervisors.

© 2012 Delmar, Cengage Learning Unit Monitors and Field Survey Instruments Draeger pumps are portable vacuum- type devices used to collect a representative gas or vapor sample to check for a known contaminant. Explosimeters are used to determine whether there are sufficient concentrations of a combustible gas mixture to produce a fire or explosion.

© 2012 Delmar, Cengage Learning Bunker Gear Includes the following: –Gloves – special heat-resistant gloves –Boots – special heat-resistant material –Coats – special heat-resistant material –Helmet – special heat-resistant material with a face shield

© 2012 Delmar, Cengage Learning Cutting, Welding, and Brazing Produce toxic fumes, generate ultraviolet radiation and electricity, and can easily start a fire.