HPU FILTERS LOW PRESSURE FILTER FROM APU UNIT. CLOSE APU HYDRAULIC FLUID VALVE. FILL FILTER WITH HYDRAULIC FLUID PRIO TO INSTALLATION. LUBRICATE GASKET.

Slides:

Advertisements

Similar presentations

Service Tips April COOLING SYSTEM To check and/or fill the cooling system it is necessary to remove the rear fender, the fuel tank (photo 1) and.

Advertisements

Peterson Product Support

CHAPTER 45 Engine Lubrication.

Motor Oil & Lube, Oil, Filter (LOF)

“The Strength of Experience”

Charging. Charging Step 1 Should the lineset length of an installation exceed the charge supplied with the outdoor unit, additional charge will be required.

Operation of the FW-720 Unit 1. Side 1 2 Inlet Hand Crank.

Name: ___________________________________ I filled _______________________’s bucket today. I filled a bucket by _________________________ _________________________________________.

REMOVE AND INSTALL THERMOSTAT AND TEST OPERATION CS4 A.1 D.6 P-5/6.

Jeopardy! ASE Review Questions Shop Safety Brake Tools Master Cylinder

Maintenance & Fluids Mixer Seminar Presented By: Rich Gochenour.

AIRCRAFT AIRWORTHINESS. AIRCRAFT AIRWORTHINESS WHAT IS AIRWORTHY?

ATD Assembly. ATD Assembly #1 Dewar Assembly #1 Status: Dewar has been completely assembled and vacuum tested. No vacuum leaks were detected on the outer.

© Blue Graphics Concept Sauer-Danfoss START-UP PROCEDURE PROPEL PUMP Instruction Sauer-Danfoss Belgium – T. Van Mossevelde.

1B-1 Fire Engine Maintenance Unit 1B – Pump Inspections and Maintenance.

How to Change Your Oil By Ben Wirjosemito. Materials Gather all materials Having them close by is important Oil pan, funnel and socket wrench Newspaper/cloth.

Step 1 Park vehicle on a level surface then engage the parking brake and turn off engine. If you cannot comfortably get under the car, raise the front.

Lubrication Systems Chapter 12 Page 143. Oil and It’s Route.

Small Engine Reassembly Briggs & Stratton OHV

Manual Transmission and Transaxle Service Walla Walla Community College Automotive Technology.

Preventative Maintenance & Troubleshooting

Engine Installation, Break-In, and In-Chassis Repairs

Floating Head Heat Exchanger

“Fix Tube Sheet” Heat Exchanger

March 19, ” Leg Valve Changeout. Required Tools and Materials 3” Wrench 9/16” Wrench 11/16 Wrench Seal Pick Clean hydraulic fluid.

Manufacturing Engineering Hydraulic and Pneumatic Systems

15 Water Supply. 2 Objectives Describe the sources of water for a municipal water supply system. Explain the purpose of a water treatment facility. Describe.

Section 703 Apparatus Inspection. Procedures The driver/operator should follow a systematic procedure for inspecting apparatus This ensures that all important.

PRE s ENT TO TRANSFER CASE WORK…….. ALL TO THE GEAR BOX……. -MAINTAINANCE….. -CHANGING OIL GEAR BOX…. -CHECKING OIL GEAR BOX……

Forging new generations of engineers. Basic Pneumatics.

HETS 5-1 M1000 SEMITRAILER CAPABILITIES

Hydraulics. An area of engineering science that deals with liquid flow and pressure.

ISX12 G & ISL G Cold Weather Operation 1. ISX12 G and ISL G Cold Weather Operation  Cold weather affects CEGR SI natural gas engines differently compared.

Weekly Checks Monday – VSP Room Tuesday – Pilothouse System Controls Wednesday – Starboard / Engine Room Thursday – Foam Room Friday – Port / Engine Room.

Monday – VSP Room weekly checks Visually Check: Hvac system for leaks & valve settings Fresh water system for leaks & valve settings VSP linkage Autopilot.

806, 806YD 3”-10”. Modification Overview  806- ( ) Cast Iron body- Threaded in seats- Internal check parts are epoxy coated iron.  806YD- (1988-present)

THEESTROGEN GARAGE GARAGE An introduction to motorcycle maintenance for the Ladies.

Oil Pressure Testing.

1 1 Staying in Compliance: Spill and Overfill Presented by: Brent Roth OPW Retail Fueling IPECA UST Seminar 2015.

Coolant Fill Coolant Check and Fill. Oil Fill & Dip Stick Main Engine Oil Fill Dip Stick Delo 400 – 40 wt. Engine Oil.

OWNER PERFORMED MAINTENANCE. AIRCRAFT AIRWORTHINESS WHAT IS AIRWORTHY?

CAR PROBLEMS? BY: KYLE KIMBALL. ALL CARS ARE DIFFERENT. FROM THE FORD MUSTANG TO THE GEO METRO, WE KNOW THAT ALL CARS ARE BUILT DIFFERENTLY. SOME ARE.

Auto Mechanics Tools Piston Ring Compressor.

5000CIV 21/2”-10” 5000CIV 21/2”-10”. Modification Overview  Production of the 5000CIV (Watts 909RPDA) began in 1998 and is current.  The 5000CIV utilizes.

15 Water Supply. 15 Objectives (1 of 2) Discuss rural water supplies. Describe how portable tanks are used to supply water for firefighting. Describe.

Contents Click a Section Tab.

STORAGE AND MAINTENANCE OF LARGE FARM EQUIPMENT Prepared by : Von G. Peavy South Region Ag Mechanics.

MAINTENANCE INTERVAL SCHEDULE D6R TRACK TYPE TRACTOR 7AR EVERY 10 SERVICE HOURS OR DAILY.

Vertical Pump Motor Manifold Upgrade. VPMM Replaces Existing Pumps, Motors, Relief Valves, Check Valves, Discharge Filters, Pump Running Pressure Gauges,

Replacing hydride bed with bottle Advantages No risk of diminished bed capacity Following jobs no longer necessary – Move pressure gauge – Replace cracked.

14 Refrigerant Recovery, Recycling, and Recharging.

JTSS / THE WAYS.

Service Procedure For Changing Engine Oil And An Oil Filter

Automatic Transmissions and Transaxles

SB Packing Automatic Downpuller Power Unit

CHAPTER 45 Engine Lubrication.

Measure Hose as 14”, 12.5”, 12.25”, 9” & cut it.

Engine Oil Changes.

Engine Oil Changes.

Service Tips April 2005.

Floating Head Heat Exchanger

BASIC PNEUMATICS.

BOP FLUID FLUSHING SIMON McMANUS WM CANNING LTD.

Light Vehicle Diesel Engines

Changing Oil and an Oil Filter

Lubrication System.

Subaru – Generation 1 and 2 Front Differential

Preventive Maintenance

Presentation transcript:

HPU FILTERS LOW PRESSURE FILTER FROM APU UNIT. CLOSE APU HYDRAULIC FLUID VALVE. FILL FILTER WITH HYDRAULIC FLUID PRIO TO INSTALLATION. LUBRICATE GASKET RING WITH OIL.

HPU FILTERS 1. OBTAIN CLEAN HYDRAULIC OIL FROM 50 GALLON TANK. 2. FILL APU UNIT TO FULL 3. VERIFY FULL LEVEL ON GAUGE IN FRONT OF APU UNIT APU HYDRAULIC OIL FILLING PROCEDURES

HPU FILTERS CLOSE APU HYDRAULIC FLUID VALVE. 1. REMOVE PLUG FROM HIGH PRESSURE FILTER CASING AND DRAIN FLUID INTO A BUCKET. 2. REMOVE FILTER FROM CASING. 3. REPLACE FILTER, CHECK O-RING ON CASING