CIM Test Methodology Overview John Simmins 5/3/2011

2 © 2010 Electric Power Research Institute, Inc. All rights reserved. Agenda 1.Progress since last meeting 2.Issues, opportunities and risks arising during the previous week 3.Verify progress against stakeholder expectations 4.General issues discussion 5.Action items for individuals 6.Expected work output during next week

3 © 2010 Electric Power Research Institute, Inc. All rights reserved. Progress Since Last Call 3 Webinars with Vendors –WednesdayMay 4 11:00 AM - 12:00 PM –FridayMay 6 9:00 AM - 10:00 AM –Monday May 9 12:00 PM - 1:00 PM.

4 © 2010 Electric Power Research Institute, Inc. All rights reserved. Verify Progress with Stakeholders Walk though Test Artifacts –Test Cases –Test Procedures –Vendor Package Samples for Remote Disconnect/Reconnect Test

5 © 2010 Electric Power Research Institute, Inc. All rights reserved. System Engineering-based Approach Southern California Edison (SCE) Use Cases Requirements Design and Implement Test Program SCE and AMI Enterprise (AMI-ENT) Requirements All Vendors Reusable Methodology Allows Additional Tests to be added at any Time Requirements derived from use cases map to test procedure steps

6 © 2010 Electric Power Research Institute, Inc. All rights reserved. EPRI CIM Part-9 Interoperability Test Cases 5 Major Test Case Areas Scheduled Meter Read On Demand Meter Read Local Area Outage Detected by Meters Tampering Detection Remote Disconnect/Reconnect

7 © 2010 Electric Power Research Institute, Inc. All rights reserved. Walk through of CIM Test Artifacts For Meter Disconnect/Reconnection Tests –Part 9 Meter Disconnect Reconnect Abstract Test Case –ECITP 2.09 Test Procedure –Vendor Package

8 © 2010 Electric Power Research Institute, Inc. All rights reserved. Abstract Test Case –Test Description Test Description: CIM standard Part-9 meter messages to/from the Meter Data Management System (MDMS) and from/to the Customer Information System (CIS) are verified to be in conformance with the IEC part 9. Unit or Systems Under Test (SUTs/UUTs) are the MDMS and CIS or equivalent systems. A scheduled meter disconnect is initiated with the MeterServiceRequest message and the meter reading data is sent in the MeterReadings message. A scheduled meter reconnect is then initiated with the MeterServiceRequest message and the meter reading data is again sent in the MeterReadings message. As shown in diagram MR , the main test steps are as follows: 1)The MeterServiceRequest messages is sent from the CIS to the MDMS.. 2)The EndDeviceControl message is sent from the MDMS to the AMI Head End or similar system. 3)The meter performs a remote disconnect. 4)The MeterReadings message is sent from the MDMS to request meter usage data for the meter. 5)The CreatedMeterReading is sent from the meter/simulator to the MDMS and onto the CIS. The required IEC part 9 XSD is used to send the CreatedMeterReading message. 6)System error conditions e.g. missing and incomplete data reads are simulated and correct error processing verified.

9 © 2010 Electric Power Research Institute, Inc. All rights reserved. Test Case Sequence Diagram

10 © 2010 Electric Power Research Institute, Inc. All rights reserved. Test Case Requirements Nominal and Error requirements Use Case B AMI-ENT version REQ Customer representative shall be able to schedule Date and Time for electric service turn On/Off and electric service limiting using AMI back office system(s). See Use Case B2 ver AMI-ENT version REQ The AMI Head End shall periodically send electric service turn off messages to the Meter until the Meter acknowledges that the turn off has been completed successfully Use Case B2 ver AMI-ENT version REQ0027 REQ-B2001-Send scheduled turn off notification Use Case B2 ver AMI-ENT REQ-B2002-Send scheduled turn off command Use Case B2 ver AMI-ENT REQ-B2003-Send scheduled turn off command confirmation Use Case B2 ver AMI-ENT REQ-B2004-Send meter read (final) Use Case B2 ver AMI-ENT REQ-B2007-Send scheduled turn on command Use Case B2 ver AMI-ENT REQ-B2008-Send scheduled turn on command confirmation Use Case B2 ver AMI-ENT REQ-B2009-Send meter read (initial) Off nominal and error requirements Use Case B1 REQ0201 v1.2 - The Meter Data Unification System shall have the ability to automatically identify and immediately log missing or incomplete data from the previous day. Use Case B1 REQ0202 v1.2- The Meter Data Unification System shall have the ability to identify and log Meters that have had missing or incomplete data in the past. Use Case B1 REQ0203 v1.2- The Meter Data Unification System shall identify and log Meters where missing or incomplete meter data for the previous day was successfully recovered through the automated on-demand read request.

11 © 2010 Electric Power Research Institute, Inc. All rights reserved. Test Case UML Diagrams Figure MR : EndDeviceControl UML Definition, from Revision / Edition: 1.0 Date: 09/00/09

12 © 2010 Electric Power Research Institute, Inc. All rights reserved. Test Procedure X-291 Diagram

13 © 2010 Electric Power Research Institute, Inc. All rights reserved. Test Procedure Detailed Test Steps Step #Ref. # Source Component Destination Component Detailed StepCompletedPass/Fail Notes/ Discrepancies 1 Use Case B AMI-ENT version REQ0224 CISMDMS Request a meter disconnect for one meter for a specific date and time. 2 IEC version 10v30, EndDevice- Control XSD MDMSMeter MDMS sends an EndDeviceControl message for a meter disconnect. 3IEC version 10v30, EndDevice- Control XSD MDMSMeterVerify MDMS sends EndDeviceControl message to the meter. Record and save the content of the message. Verify meter performs the disconnect operation. Verify the MDMS records the meter disconnect status in the log. ECITP 2.09 CIS to MDMS Disconnect/Reconnect Interoperability Detailed Test Steps

14 © 2010 Electric Power Research Institute, Inc. All rights reserved. Test Procedure Execution Record Test ECITP 2.09 CIS to MDMS Interoperability Test Record Test date: ___________________________________ Test time ____________________________________ Test witnesses: ________________________________ ______________________________________________ Test PASS/FAIL EndDeviceEvent, IEC version: 10v30, XSD Notes: ____________________________________________________ System Under Test (SUT): ______________________________ SUT version/release identifier: __________________________ SUT IS / IS NOT currently released Test Configuration notes and restrictions: ____________________________________________________

15 © 2010 Electric Power Research Institute, Inc. All rights reserved. Current Demonstration – Vendor Package Based on SCE Use Case D4 - Distribution operator locates outage using AMI data and restores service Single document with all necessary demo material –Use case requirements mapped to individual test steps –OMS, MDMS and AMI Head End test steps –WSDLs and XSDs –Sample meter outage EndDeviceEvent message

16 © 2010 Electric Power Research Institute, Inc. All rights reserved. Expected Work Output During the Next Week Report Format for remaining demonstration packages

17 © 2010 Electric Power Research Institute, Inc. All rights reserved. Questions & Contact Informatation John J. Simmins, Ph.D. Senior Project Manager – Smart Grid Electric Power Research Institute (EPRI) 942 Corridor Park Blvd. Knoxville, TN (Office) (Cell)