Problem-1: A rigid coupling has a bore diameter of 50 mm. Four machined bolts on a bolt circle of 125 mm diameter and fitted in reamed holes. If the bolts.

Slides:

Advertisements

Similar presentations

Design of Steel Tension Members

Advertisements

PROBLEM-1 The pipe shown in the figure has an inner diameter of 80 mm and an outer diameter of 100 mm. If its end is tightened against the support at A.

Mechanical Department

1 Bolts in Tension pt1 Andrei Lozzi. The flanges at the end of the two turbine shafts seen above, are bolted together to form a very rigid friction coupling.

Section VI Shaft Design.

Shear Design of Beams CE Steel Design Class By, Amit H. Varma.

Connection Design.

Shear Design of Beams CE Steel Design Class By: Amit H. Varma.

Torsion: Shear Stress & Twist ( )

Design of Shaft A shaft is a rotating member usually of circular cross-section (solid or hollow), which transmits power and rotational motion. Machine.

Strength of Material-5 Torsion Dr. Attaullah Shah.

MACHINE DESIGN II CLUTCHES.

Products made from rolling

Connection of flange plate with web

Screws, Fasteners, and the Design of Nonpermanent Joints

CM 197 Mechanics of Materials Chap 20: Connections

Lecture # 2 Allowable Stress Objective:

THEORIES OF FAILURE THEORIES OF FAILURE FOR DUCTILE MATERIALS

PROBLEM-1 State of stress at a point is represented by the element shown. Determine the state of stress at the point on another element orientated 30

Rehabilitation and maintenance of buildings - 03

Mechanical Design of Machine Elements/Components

PROBLEM mm x y 800 mm P = 1500 N z y 50 mm 100 mm

1 Coupling Design Section VII. 2 Coupling? Classifications of Coupling A) Rigid Coupling B) Flexible Coupling Analysis of Bolts Talking Points.

Friction Clutches A clutch enables two co-axial shafts to be engaged or disengaged while at rest or in relative motion.

Shear Stress and Strain

Problem-1 A section of commercial steel shafting 2.0 m long between bearings carries a 1000 N pulley at its midpoint, as shown in Figure. The pulley is.

Experiment 11 Gearing.

Section VIII Belt Drives.

Section XI Keys, Pins, & Splines.

UNIT-05. Torsion And Buckling of columns Lecture Number-2 Mr. M. A. Mohite Mechanical Engineering S.I.T., Lonavala.

MECHANICS OF MATERIALS Third Edition Ferdinand P. Beer E. Russell Johnston, Jr. John T. DeWolf Lecture Notes: J. Walt Oler Texas Tech University CHAPTER.

UNIT-05. Torsion And Buckling of columns

PROBLEM-1 The pipe shown in the figure has an inner diameter of 80 mm and an outer diameter of 100 mm. If its end is tightened against the support at A.

Machine Design I (MCE-C 203) Mechatronics Dept., Faculty of Engineering, Fayoum University Dr. Ahmed Salah Abou Taleb Lecturer, Mechanical Engineering.

PROBLEMS ON TORSION.

1 Clutches Section IX. 2 Clutch? Types of Clutches Plate or Disk Clutches Cone Clutches Engaging Cone Clutches Talking Points.

CHAPTER OBJECTIVES To show how to transform the stress components that are associated with a particular coordinate system into components associated with.

-Elastic Properties of Solids AP Physics C Mrs. Coyle.

Teaching Innovation - Entrepreneurial - Global

1 - An AISI 1020 cold- rolled steel tube has an OD of 3.0 inch. The internal pressure in the tube is 6,840 psi. Determine the thickness of the tube using.

ME 307 Machine Design I ME 307 Machine Design I. ME 307 Machine Design I ME 307 Machine Design I 8-1 Thread Standards and Definitions 8-2The Mechanics.

D. V. RAMANAREDDY VARDHAMAN COLLEGE OF ENGINEERING

1. Two rods, one of nylon and one of steel, are rigidly connected as shown in Fig. P.1.2. Determine the stresses and axial deformations when an axial load.

Design of shaft couplings

Multi plate clutches In a multi plate clutch, the torque is transmitted by friction between several pairs of co-axial annular driving faces maintained.

Friction Clutches A clutch enables two co-axial shafts to be engaged or disengaged while at rest or in relative motion.

Section VII Coupling Design.

Single Plate Clutch A clutch enables two co-axial shafts to be engaged or disengaged while at rest or in relative motion.

Visit for more Learning Resources

Chapter 07-Clutch And Bearings

PROBLEMS ON TORSION.

Limit, Fit & Tolerance – Numerical Problems

CE Steel Design Class By, Amit H. Varma

Multi plate clutches In a multi plate clutch, the torque is transmitted by friction between several pairs of co-axial annular driving faces maintained.

BFC Structural Steel and Timber Design

CONNECTION Prepared by : Shamilah

Strength of Material Torsion Dr. Attaullah Shah.

Part II Design of Fasteners and Joints

Chapter 2 BELTING SYSTEM.

Yielding And Fracture Under Combine Stresses

Presentation transcript:

Problem-1: A rigid coupling has a bore diameter of 50 mm. Four machined bolts on a bolt circle of 125 mm diameter and fitted in reamed holes. If the bolts are made from the same material as the shaft, with an ultimate tensile strength of 550 MPa and a yield point in tension of 345 MPa, determine the necessary size of bolts to have the same capacity as the shaft in torsion.

Problem-2: Assume that a flange coupling has the following specifications: Number of bolts: 6. Size of bolts: 12 mm diameter Preloading of bolts: 22 KN in each bolt. Inner diameter of contact: 175 mm. Outer diameter of contact: 200 mm. Speed of rotation of coupling: 300 rpm. Coefficient of friction: 0.15 Shaft diameter: 50 mm. Shaft material, annealed steel with an ultimate tensile strength of 586 MPa and a yield point in tension of 310 MPa. The bolts are set in large clearance holes in the coupling. 1)Determine the maximum power capacity based upon friction such that slip occurs between faces of contact. 2)Compare the shaft power capacity with the friction power capacity. Assume steady load conditions and that the shaft is in torsion only.

Figure-2

Problem-3 Set up the equations or relations necessary to determine: a)the hub diameter DH. b)the web thickness t. c)the flange thickness h.

Problem-4: A flange coupling connects two 50 mm diameter lengths of commercial shafting. The coupling webs are bolted together with four bolts of the same material as the shaft. The bolts are set in clearance holes. The diameter of the bolt circle is 240 mm and the web thickness is 22 mm. a)Determine the minimum bolt diameter required transmitting the same torque that the shaft can transmit. b)What power may be transmitted at 200 rev/min under steady state conditions?