Products & Accessories Details System Highlights Hands On Sure-Weld TPO Products & Accessories Details System Highlights Hands On

Sure-Weld Products & Accessories

60 sq. ft. per gallon finished surface. Sure-Weld™ Bonding Adhesive is a high strength solvent-based contact adhesive that allows bonding of Sure-Weld membrane to various porous and non-porous substrates. Coverage rate: 60 sq. ft. per gallon finished surface.

Weathered Membrane Cleaner is used to clean in-service Sure- Weld membrane prior to the welding process. It helps to loosen and remove dirt and other contaminants from the surface of the Sure-Weld membranes and leaves a suitable surface for welding or the subsequent application of HP-250 Primer.

HP-250 Primer is a solvent-based product designed for priming TPO surfaces prior to the application of SecurTAPE™ and all pressure-sensitive products.

Cut-Edge Sealant is a free flowing polymeric material designed for sealing cut edges (exposed fabric) of Sure- Weld reinforced membrane.

Thermoplastic One Part Sealant is a single component, moisture curing, elastomeric polyether sealant that is compatible with Carlisle’s Thermoplastic membranes. The material is designed to provide a flexible, durable and long lasting seal around hard-to-flash penetrations in Thermoplastic Roofing Systems. Thermoplastic One Part Pourable Sealer provides rapid skin time when exposed to atmospheric moisture forming a waterproof rubber surface in less than one (1) hour. Moisture curing continues, until a two (2) – inch deep solid rubber seal encases the penetration. Complete cure time will vary depending on relative humidity and temperature. The sealant’s one-part, pourable consistency allows for quick pocket filling without mixing. Carlisle’s HP-250 Primer must be applied to all surfaces, including membrane, flashings and penetrations that will be in contact with the Thermoplastic One Part Pourable Sealant. Unused sealant remaining in a pouch will remain useable up to 30 days if pouch is resealed with original cap.

Sure-Seal® Water Cut-Off Mastic is a one-component, low viscosity, self-wetting butyl blend mastic used with roofing and waterproofing systems. It is primarily used as a sealing agent and also used when membrane is being terminated using a compression-type seal.

PT 304 Sealant PT 304 polyurethane is a one part ready-to-use, permanently flexible, fast moisture cure, nonsag, paintable, multi-purpose construction sealant and adhesive. It is excellent for sealing dynamically moving joints.

Pre-Fabricated Products

RUSS For Angle Changes and Perimeter sheets (6” & 10”) TPO Pressure-Sensitive RUSS is a reinforced TPO membrane strip with a pressure sensitive tape laminated along one edge. Placed below the deck membrane, TPO Pressure-Sensitive RUSS™ provides membrane securement at angle changes without penetrating the sheet.

Cover Strip Sure-Weld Pressure-Sensitive Cover Strip is TPO membrane laminated to a fully cured synthetic rubber pressure sensitive adhesive. Available in white, gray and tan, 6”, 9”, & 12”. PS Cover Strip provides maximum protection against inclement weather and is ideal for stripping in shop bent metal drip edge.

Outside Corners A pre-molded corner flashing for outside corners. Available in white, gray or tan. .060” thick

Inside Corners Pre-molded inside corner. Eliminates “pig-ear”

Molded Sealant Pockets Carlisle Molded TPO Sealant Pockets consist of an interlocking, two piece, injection molded flexible pocket with a rigid polypropylene vertical wall and preformed deck flanges. Used with Carlisle sealant and primer, this product effectively waterproofs pipe clusters or other odd shaped penetrations on Sure-Weld roofing systems.

Larger pockets also available

Pre-Molded Pipe Seal (boot) A pre-molded white, gray or tan pipe flashing used for pipe penetrations. Available for 1-6 inch diameter pipes with clamping rings included

1”-6” sizes available Split Pipe Seals Sure-Weld TPO Split Pipe Seals are fabricated flashings made of 45-mil reinforced Sure-Weld membrane. Split (cut) and overlap tabs allow the pipe seals to be opened and wrapped around a round pipe with an obstruction.

Square Tubing Wraps Sure-Weld TPO Square Tubing Wraps are made of 45-mil reinforced Sure-Weld membrane. A split (cut) and overlap tab allow the seals to be opened and wrapped around square tubing. Sure-White tape is included and required at top of wrap for final termination.

Curb Wrap Corners Sure-Weld TPO Curb Wrap Corners are made of 45-mil reinforced Sure-Weld membrane. With six sizes available to fit curbs up to 6' by 6', this innovative product reduces installation time compared to conventional flashing methods.

2006 SURE-WELD DETAILS

SURE-WELD ADHERED DETAILS

SURE-WELD MFRS

Variations of achieving perimeter sheets required

4’ half sheets used when using 8’ field sheets

RUSS USED FOR PERIMETERS 4’ min At least one finger must extend to Outside edge of building. (FM requirements differ) 4’ min RUSS USED FOR PERIMETERS

RUSS USED FOR PERIMETERS 8’ field sheets No fasteners needed here Fasten the field Seams as required per spec. RUSS USED FOR PERIMETERS

Adhering sheet to RUSS RUSS strip Apply HP-250 Primer to back of sheet Set sheet Fold back sheet to expose RUSS Apply HP-250 Primer to back of sheet Remove poly from RUSS Roll sheet onto RUSS Strip and Roll from top to achieve adhesion. Apply HP-250 Primer to back of sheet RUSS strip

Perimeter Sheets 8’ field sheets 10’ field sheets 12’ field sheets 5’ or 6’ field sheets 12’ field sheets 6’ field sheets and two perimeters always required