ME 3351 Manufacturing Processes Tutorial 5 Eng. Ahmad Aljazea.

Slides:

Advertisements

Similar presentations

Fundamental of Metal Casting

Advertisements

FUNDAMENTALS OF CASTING

IE 337: Materials & Manufacturing Processes

Fundamental of Metal Casting Chapter 10

FUNDAMENTALS OF METAL CASTING

Casting Processes Example Parts Requirements Terminology

ME 3351 Manufacturing Processes Tutorial 2 Eng. Ahmad Aljazea.

MT-284 MANUFACTURING PROCESSES

Types of Pattern Pattern Allowances

Heating/Cooling Curve & Energy Calculations. Which of the following measures the average kinetic energy of a sample? 1.Mass 2.Volume 3.Specific heat 4.Temperature.

Manufacturing, Engineering & Technology, Fifth Edition, by Serope Kalpakjian and Steven R. Schmid. ISBN © 2006 Pearson Education, Inc.,

©2010 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 4/e Classification of solidification processes.

MSE 440/540: Processing of Metallic Materials

Presented by: Chandra bhan prajapati 2008AMD2934.

FUNDAMENTALS OF METAL CASTING

Casting Workshop Technology

MT-284 MANUFACTURING PROCESSES INSTRUCTOR: SHAMRAIZ AHMAD MS-Design and Manufacturing Engineering Topic: Casting Defects and Mold.

Moulding Materials and their Characteristics

ME 3351 Manufacturing Processes Tutorial 3 Eng. Ahmad Aljazea.

FUNDAMENTALS OF METAL CASTING

Sinhwa-Steel Park Min Woo. SINHWA-Steel Located in Changwon Produce the Various Steel product.

Final Exam Review.

Manufacturing, Engineering & Technology, Fifth Edition, by Serope Kalpakjian and Steven R. Schmid. ISBN © 2006 Pearson Education, Inc.,

Characteristic Physical Properties Some examples of quantitative physical properties include: Density Freezing point Melting point Boiling point These.

VISCOSITY The measure of a fluid’s resistance to flow. High Viscosity – thick Low Viscosity - thin.

Manufacturing Engineering Technology in SI Units, 6th Edition PART II: Metal Casting Processes and Equipment Presentation slide for courses, classes,

Fundamentals of Metal Casting

Manufacturing Processes

Manufacturing, Engineering & Technology, Fifth Edition, by Serope Kalpakjian and Steven R. Schmid. ISBN © 2006 Pearson Education, Inc.,

Casting process.

Landmark University, MECH DEPT., MCE 329, ADEDIRAN A.A

Phase Change Analysis Chapter 9. Training Manual Inventory # March 15, Chapter Overview Phase Change –Terminology –Theory –Material Properties.

  There is a relationship between volume and the number of moles of a gas  V = kn  V/n = k  Volume is directly proportional to the number.

Characteristic Physical Properties. Characteristic physical properties are properties that are unique to a substance and can be used to identify it. For.

SOLIDIFICATION OF METALS. Cooling curve for a pure metal during casting A pure metal solidifies at a constant temperature equal to its freezing point(same.

Heating Curves and Energy. Which of the following measures the average kinetic energy of a sample? 1.Mass 2.Volume 3.Specific heat 4.Temperature 5.Heat.

Preparation of Plant tissues for histological study.

Heat Transfer Su Yongkang School of Mechanical Engineering # 1 HEAT TRANSFER CHAPTER 9 Free Convection.

SPECIFIC LATENT HEAT. Objective At the end of this lesson, you should be able to : At the end of this lesson, you should be able to : State that transfer.

MSE 440/540: Processing of Metallic Materials

Material Science & Metallurgy Non Equilibrium Cooling

Manufacturing Process

DR S. & S. S. GHANDHY GOVERNMENT ENGINEERING COLLEGE , SURAT.

Injection molding Injection molding is similar to casting in that

Fundamentals of Metal Casting

Classification of solidification processes

Heating/Cooling Curve & Energy Calculations

Materials and Processes

Fundamentals of Metal-Casting

Thickness of a Thin Layer

Part II Metal-Casting Processes and Equipment

by Norman E. Dowling. ISBN

FUNDAMENTALS OF METAL CASTING

Solidification Time Whether the casting is pure metal or alloy, solidification takes time. The total solidification time is the time required for the casting.

Sand Casting Sand casting, also known as sand-mold casting, consists of pouring molten metal into a sand mold, allowing the metal to solidify, and then.

Chapter 2 Material and Manufacturing Properties

PHYSICAL PROPERTIES OF MATERIALS

Tutorial in Mechanical Properties

Sand casting. Steps: 1.Mechanical Drawing of the part

FUNDAMENTALS OF METAL CASTING

Chapter 2-FUNDAMENTALS OF METAL CASTING

Solidification of Metals and Alloys

Casting process.

Riser Design Riser is a waste part, as it will be separated from the casting body after the mold is destroyed and reused for casting (for expandable mold.

Heat Transfer from Extended Surfaces (Fins)

FIRST TIME RIGHT Component Name : Adapter Component weight : 18.2Kgs

Fundamentals of casting

*Always measured in units cubed (u3)

Heating the Metal The heat energy required is the sum of (1) the heat to raise the temperature to the melting point, (2) the heat of fusion to convert.

Presentation transcript:

ME 3351 Manufacturing Processes Tutorial 5 Eng. Ahmad Aljazea

Tables 4.1 & 4.2

Heating and Pouring 10.1 A disk 40 cm in diameter and 5 cm thick is to be casted of pure aluminum in an open mold operation. The melting temperature of aluminum = 660 C and the pouring temperature will be 800 C. Assume that the amount of aluminum heated will be 5% more than needed to fill the mold cavity. Compute the amount of heat that must be added to the metal to heat it to the pouring temperature, starting from a room temperature of 25 C. The heat of fusion of aluminum = J/g. Other properties can be obtained from Tables 4.1 and 4.2 in this text. Assume the specific heat has the same value for solid and molten aluminum.

10.15 In the casting of steel under certain mold conditions, the mold constant in Chvorinov's Rule is known to be Cm = 4.0 min/cm2, based on previous experience. The casting is a flat plate whose length = 30 cm, width = 10 cm, and thickness = 20 mm. Determine how long it will take for the casting to solidify.

Solution: Volume V = 30 x 10 x 2 = 600 cm3 Area A = 2(30 x x x 2) = 760 cm2 Chvorinov’s Rule: TST = Cm (V/A)2 = 4(600/760)2 = 2.49 min

10.16 Solve for total solidification time in the previous problem only using a value of n = 1.9 in Chvorinov's Rule. What adjustment must be made in the units of Cm? Solution: Chvorinov’s Rule: TST = Cm (V/A)1.9 = 4(600/760)1.9 = 2.55 min The units for Cm become min/in1.9 - strange but consistent with Chvorinov’s empirical rule.