SubDrive Constant Pressure Controller By Franklin Electric

SubDrive Family

SubDrive Constant Pressure Controller The CP Water – SubDrive 75 uses state-of-the-art electronics technology to provide constant water pressure through variable speed control of standard ¾, 1 or 1½ Hp pump ends, adding significant value and performance to Residential & Commercial water systems. Produce 1½ Hp performance with a ¾ Hp pump end.

SubDrive Constant Pressure Controller The CP Water – SubDrive 150 was the second addition to the CP Water family of SubDrives. The SubDrive 150 provides constant water pressure through variable speed control of a 1½ , 2 or 3 Hp pump ends to produce the performance of a 3 Hp pump.

SubDrive Constant Pressure Controller The CP Water – SubDrive 300 is the latest addition to the CP Water family of SubDrives. The SubDrive 300 provides constant water pressure through variable speed control of a 3 or 5 Hp - 4”& 6” pump ends to produce the performance of a 5 Hp pump curve.

SubDrive Constant Pressure System

SubDrive

SubDrive Application Data

Application Data CP Water – SubDrive 75 is designed for use with a ¾ Hp pump mounted to a 1½ Hp 3 phase Franklin Electric motor. 1 Hp and 1½ Hp pump end may also be used. This innovation variable speed controller is designed for applications with a wide range of flow demand, includes large homes, ground source heat pumps, restaurants, bed & breakfast and sprinkler systems. CP Water SubDrive 75 is UL recognized for U.S.A. and Canada.

Application Data CP Water – SubDrive 150 is designed for use in residential or light commercial applications with a 1½ Hp pump mounted to a 3 Hp Franklin Electric 3-phase motor. 2 Hp and 3 Hp pump end may be used. Ideal for multi home and irrigation applications.

Application Data CP Water – SubDrive 300 is designed for use in residential or light commercial applications with a 3 Hp pump mounted to a 5 Hp Franklin Electric 3-phase motor. 5 Hp pump end may be used. For flows of up to 90 gpm

SubDrive Application Data Specifications

Specifications Input (from power source) Output (to motor) Voltage 190 – 260V 1-phase Frequency 60/50 Hz Amps (RMS) SD75 11A, SD150 23A, SD300 36A Output (to motor) Voltage Variable / 3-Phase Frequency Variable (30-80 Hz) Amps (RMS) SD75 5.9A, SD150 10.9A, SD300 17.8A

Specifications ¾, 1 or 1½ Hp (Selectable) Model Pump Rating Motor Rating SubDrive 75 ¾, 1 or 1½ Hp (Selectable) 1½ Hp, 230 VAC (Three-phase) SubDrive 150 1½ , 2 or 3 Hp (Selectable) 3 Hp, 230 VAC (Three-phase) SubDrive 300 3 or 5 Hp (Selectable) 5 Hp, 230 VAC (Three-phase)

SubDrive Application Data Specifications Features & Benefits

Features & Benefits Constant water pressure with a wide range of settings (25 to 80 psi). Better than city pressure. 50 psi factory setting. Soft start feature prevents water hammer and increases motor life. Less stress & torque on riser pipe. Works with small pressure tanks or with larger tanks already in place.

Features & Benefits UL recognized for U.S. and Canada. Smart Reset technology allows well recovery before restarting the pump. Single-phase input power with three-phase motor performance (SD75, SD150, SD300)

Features & Benefits Works with a small pressure tank or larger tanks already in place. Minimum tank volume: 2 gallons. With 3 phase motor, no need to pull the pump. Excellent radio frequency interference shielding. Less inrush current = longer motor life.

Features & Benefits Less operating cost Uses only the horse power required Reduced wire size (SD75, 150, 300) due to 3-phase. I.E. 350 Ft length: 3Hp 230V single phase #8 3Hp 230V three phase #12

Features & Benefits Wide range of input voltages allowable Easy to install

$2, 951.60 Standard System $2,875.96 SubDrive System

CP SUBDRIVE SIZING

CP SUBDRIVE SIZING

CP SUBDRIVE SIZING