The George W. Woodruff School of Mechanical Engineering ME3180 ME 3180: Machine Design Mechanical Springs Lecture Notes 1

The George W. Woodruff School of Mechanical Engineering ME3180 Mechanical Springs There are Three Types of Spring: Helical Compression, Extension and Torsion These Springs: Produce a pull, a push, or a twist (torque) force when displaced. Store or absorb energy. May be made of round or rectangular wire bent into a suitable form such as a coil, or made of flat stock loaded as a beam. 2

The George W. Woodruff School of Mechanical Engineering ME3180 Mechanical Springs 3

The George W. Woodruff School of Mechanical Engineering ME3180 Push Function Push function is provided by helical compression springs, spring washers, volute springs, and beam springs. These are shown in the previous page. Helical Compression Springs: Used in applications involving large deflections, such as shock absorbers in automobiles or to hold batteries in consumer products. Used in valve-return springs in engine, die springs, etc. Conical Springs: Spring rate is nonlinear. By varying coil pitch, a nearly constant spring rate can be obtained. Advantage is the ability to close to a height as small as one wire diameter if the coils nest. 4

The George W. Woodruff School of Mechanical Engineering ME3180 Push Function – Cont’d Barrel/Hourglass/Variable Pitch Springs: Can be thought of a two conical springs back to back, also having a nonlinear spring rate. Barrel, hourglass, and variable pitch springs are used to minimize resonant surging and vibration. Spring Washers: Used for small deflections associated with motion along a bolt or other guide. Used to load something axially, such as to take up endplay on a bearing. Volute Springs: Can be used for damping and also to resist buckling. Very expensive. Shear cutter for trimming, and has significant friction and hysteresis (significant energy loss) Beam Springs: Can be used to push or pull. Examples are diving boards. Spring rate and stress distribution can be controlled with changes in beam width or depth along its length. Loads can be high but deflections are limited. 5

The George W. Woodruff School of Mechanical Engineering ME3180 Pull Function Pull function is provided by helical extension springs and constant force springs. Helical Extension Springs: Capable of large deflection. Used in door closers and counterbalances, automobile wiper blades, children’s car seats and car hoods. Hooks more highly stressed than coils and usually fail first. When hook fails this spring becomes unsafe. 6

The George W. Woodruff School of Mechanical Engineering ME3180 Twisting Function Twisting function is provided by helical torsion springs and spiral springs (coils in the same plane). Helical Torsion Springs: Used for garage-door counter-balancers and counterbalancing of such things as doors which rotate about a horizontal edge. Clothespins, mousetraps and finger exercisers are examples. Spiral Springs:  Hairsprings are used in instruments and mechanical clocks and watches. One of their characteristics is low hysteresis (small energy loss).  Brush Springs: Hold motor and generator brushes against their commutators. 7

The George W. Woodruff School of Mechanical Engineering ME3180 Twisting Function – Cont’d Motor, Clock or Power Springs: Used to supply rotational energy and used in windup clocks and mechanical toys. Prestressed Power Springs: Has large energy storage capacity. Used in seatbelt retractors. Constant-Torque Spring Motor: Used to provide level torque. Drawbar Springs: Unlike helical extension spring, it will support the load safely when it fails. 8

The George W. Woodruff School of Mechanical Engineering ME3180 Spring Rate Every spring configuration has a spring rate, k, defined as slope of its force-deflection curve. If slope is constant, it is a linear spring, and Where: F is applied force, and y is deflection. When spring rate varies with deflection, it is called a nonlinear spring. We often want a linear spring to control loading. Many spring configurations have constant spring rates and few have zero rates (constant force). 9

The George W. Woodruff School of Mechanical Engineering ME3180 Spring Rate – Cont’d When multiple springs are combined, resulting spring rate depends on whether they are combined in series or parallel. Springs in series have same force passing through them, as each contributes to total deflection (see Fig. 13-1a). (13.2b) 10

The George W. Woodruff School of Mechanical Engineering ME3180 Spring Rate – Cont’d Springs in parallel have same deflection, and total force is split among them (see Fig. 13-1b). For springs in parallel, individual spring rates add directly. k total = k 1 + k 2 + k 3 + …. + k n 11

The George W. Woodruff School of Mechanical Engineering ME3180 Spring Materials Limited number of materials and alloys are suitable for use as springs. Ideal spring material would have high ultimate strength, high yield point, and low modulus of elasticity in order to provide maximum energy storage (area under elastic portion of stress-strain curve). For dynamically loaded springs, fatigue strength properties of material are of primary importance. 12

The George W. Woodruff School of Mechanical Engineering ME3180 Spring Materials – Cont’d High strength and high yield points are attainable from medium-to high- carbon and alloy steels, and these are most common spring materials, despite their high modulus of elasticity. Few stainless-steel alloys are suitable for springs, as are beryllium copper and phosphor bronze, among copper alloys. Commonly used spring materials are shown in Table Springs are manufactured by hot-or cold-working process. Winding springs induces residual stresses through bending. These stresses are relieved through mild heat treatment. 13

The George W. Woodruff School of Mechanical Engineering ME

The George W. Woodruff School of Mechanical Engineering ME3180 Spring Wire It is common to use round wire as spring material. It is available in selection of alloys and wide range of sizes. Rectangular wire is available only in limited sizes. Some common wire alloys are shown in Table Commonly available stock wire sizes are shown in Table Designer should try to use these sizes for best cost and availability, though other sizes not shown are also available. 15

The George W. Woodruff School of Mechanical Engineering ME

The George W. Woodruff School of Mechanical Engineering ME3180 Tensile Strength Relationship between wire size and tensile strength is shown in Fig Cold-drawn process used in reducing wire diameter is responsible for hardening and strengthening material at expense of much of its ductility. Fig is semilog plot of wire strength versus diameter based on extensive testing. Empirical equation resulting from fitting exponential function through data for five of materials, shown in Fig is: Where A and m are defined in Table 10-4 for these wires materials. (10.14) 17

The George W. Woodruff School of Mechanical Engineering ME

The George W. Woodruff School of Mechanical Engineering ME

The George W. Woodruff School of Mechanical Engineering ME3180

ME3180

ME3180 Shear Strength Extensive testing has shown that a reasonable estimate of ultimate strength in torsion of common spring material is 67% of ultimate tensile strength. Distortion-energy theory can be applied to obtain torsional yield strength: Above approach results in range of values for steels below: (13.4) 22 (10-15)