Optimal Fin Shapes & Profiles P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Geometrical Optimization is the Basic Goal.

Slides:

Advertisements

Similar presentations

Conduction Conceptests

Advertisements

Electronics Cooling MPE 635 Mechanical Power Engineering Dept.

Part F Practical Applications. 28. Fan-Cooled Enclosure of a PC System Physical System The physical system of interest is a fan-cooled enclosure containing.

Multi Dimensional Steady State Heat Conduction P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi It is just not a modeling.

Extended Surfaces Chapter Three Section 3.6.

UNSTEADY-STATE HEAT CONDUCTION

Extended Surface Heat Transfer

Analysis of Simple Cases in Heat Transfer P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Gaining Experience !!!

Example 1:- An annular alloyed aluminum (k = 180 W/m . K ) fin of rectangular profile is attached to the outer surface of a circular tube having an outside.

Experimental and Numerical Study of the Effect of Geometric Parameters on Liquid Single-Phase Pressure Drop in Micro- Scale Pin-Fin Arrays Valerie Pezzullo,

Jed Goodell Jesse Williams. Introduction Problem How much heat does a particular heat sink dissipate How many fins are needed to dissipate a specific.

CHE/ME 109 Heat Transfer in Electronics LECTURE 18 – FLOW IN TUBES.

Scoping Study of He-cooled Porous Media for ARIES-CS Divertor Presented by John Pulsifer Major contributor: René Raffray University of California, San.

M. Yoda, S. I. Abdel-Khalik, D. L. Sadowski, B. H. Mills, and J. D. Rader G. W. Woodruff School of Mechanical Engineering Parametric Design Curves for.

CHE/ME 109 Heat Transfer in Electronics LECTURE 8 – SPECIFIC CONDUCTION MODELS.

Thermal Development of Internal Flows P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Concept for Precise Design ……

Closure of Kern’s Method

One Dimensional Polar Geometries For Conduction with Heat Generation P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi A.

Development in Double Pipe HEAT EXCHANGER for Concurrence & Better Economy! More New Geometric Ideas : Just for Economy !!! P M V Subbarao Professor Mechanical.

Solutions of the Conduction Equation P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi An Idea Generates More Mathematics….

Heat Convection : Cylinder in Cross Flow P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi A Common Industrial Application.

M. Yoda, S. I. Abdel-Khalik, D. L. Sadowski and M. D. Hageman Woodruff School of Mechanical Engineering Extrapolating Experimental Results for Model Divertor.

Thermo-economic Optimization of STHE P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Minimizing capital and operating costs of shell.

1-D Steady Conduction: Plane Wall

Heat Sink Selection Thermal Management of Electronics

Design of Heat Sinks P M V Subbarao Mechanical Engineering Department IIT Delhi Success Based on Cooling Challenges …….

Thermal Analysis and Design of Cooling Towers

Parametric Study of Turbofan Engine Performance P M V Subbarao Professor Mechanical Engineering Department Its Time to think about fuel Economy……

Design Analysis of Plate Heat Exchangers

Exergy Analysis of STHE P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Formalization of Thermo-economics…..

1/22/05ME 2591 ME 259 Heat Transfer Lecture Slides IV Dr. Gregory A. Kallio Dept. of Mechanical Engineering, Mechatronic Engineering & Manufacturing Technology.

One Dimensional Non-Homogeneous Conduction Equation P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Another simple Mathematical.

1/22/05ME 2591 ME 259 Heat Transfer Lecture Slides II Dr. Gregory A. Kallio Dept. of Mechanical Engineering, Mechatronic Engineering & Manufacturing Technology.

Min-Max Problems Unit 3 Lesson 2b – Optimization Problems.

Enhancement of Heat Transfer P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Invention of Compact Heat Transfer Devices……

Two Dimensional Steady State Heat Conduction

The Family of Shell and Tube Heat Exchangers P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Family members with Simple Geometrical.

Double Pipe HEAT EXCHANGERS with Finned Inner Tube P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Ideas for Creation of Compact.

Analytical Modeling of Forced Convection in Slotted Plate Fin Heat Sinks P. Teertstra, J. R. Culham & M. M. Yovanovich Microelectronics Heat Transfer Laboratory.

Heat Transfer from Extended Surfaces Heat Transfer Enhancement by Fins

Chapter 7 External Convection

Convection in Flat Plate Boundary Layers P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi A Universal Similarity Law ……

One Dimensional Non-Homogeneous Conduction Equation P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Another simple Mathematical.

M. Yoda, S. I. Abdel-Khalik, D. L. Sadowski, B. H. Mills and M. D. Hageman G. W. Woodruff School of Mechanical Engineering Correlations for Divertor Thermal-Hydraulic.

Double Pipe HEAT EXCHANGERS with Low Thermal Resistance P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Ideas for Creation of Isotropically.

Performance Analysis of Heat Exchangers P M V Subbarao Professor Mechanical Engineering Department I I T Delhi A First Step in Techno-Economics of HXs?!?!?!

1 Teaching Innovation - Entrepreneurial - Global The Centre for Technology enabled Teaching & Learning D M I E T R, Wardha DTEL DTEL (Department for Technology.

 Other than minimizing the fence for a garden, there are more interesting optimization problems…  When designing a building, the cost of building materials.

Design and Analysis of Fins with Realistic Boundary Conditions P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Design for.

HEAT TRANSFER Problems with FEM solution

Extended Surfaces (Fins) Bhagwat Singh Shishodia Associate Professor Manav Rachna International University.

AFE BABALOLA UNIVERSITY

From: Optimal Shapes of Straight Fins and Finned Heat Sinks

Date of download: 9/27/2017 Copyright © ASME. All rights reserved.

From: Thermal-Hydraulic Performance of MEMS-based Pin Fin Heat Sink

Thermal Design and Optimization of Heat Sinks

INTRODUCTION : Convection: Heat transfer between a solid surface and a moving fluid is governed by the Newton’s cooling law: q = hA(Ts-Tɷ), where Ts is.

Chapter 3: One-Dimensional Steady-State Conduction

Optimizing Area/SA/Volume

Chapter 3: Steady Heat Conduction

Extended Surface Heat Transfer

Design Analysis of Plate Heat Exchangers

Double Pipe HEAT EXCHANGERS with Finned Inner Tube

Parametric Study of STHE Design

THERMODYNAMIC IN ELECTRONICS

What is Fin? Fin is an extended surface, added onto a surface of a structure to enhance the rate of heat transfer from the structure. Example: The fins.

Heat Transfer from Extended Surfaces (Fins)

P M V Subbarao Professor Mechanical Engineering Department I I T Delhi

What are Fins ? Fins are extended surfaces used to increase the rate of heat transfer. It is made of highly conductive materials such as aluminum.

THERMODYNAMIC IN ELECTRONICS

Presentation transcript:

Optimal Fin Shapes & Profiles P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Geometrical Optimization is the Basic Goal of Optimal Design ….

CYLINDRICAL SPINE (Pin Fins) b d T  & h  TbTb Pin fin with adiabatic tip and corrected height:

Pin Fins : Profile Optimization Sonn and Bar-Cohen (1981) developed an optimization method based on minimization of the spine volume. The objective function is to maximize heat dissipation for a given volume. With So that b d T  & h  TbTb

Optimization Pin Fin Profile We find the point where: The results is the transcendental equation Where

Trial and error method of root finding, gives: Or Volume of maximum heat dissipating pin fin:

For Strip fin: For pin fin:

LONGITUDINAL FIN OF TRIANGULAR PROFILE The differential equation for temperature excess : L x=0 b x=b x qbqb

The differential equation for temperature excess is a form of Bessel’s equation: The particular solution foris: The fin heat dissipation is: The fin efficiency is:

Optimum Shapes : Triangular Fin L=1 With This makes

Optimum Shapes Iterative solving yields  T = and

Comparison of Longitudinal Fins Rectangular Profile: Triangular Profile: For the same material, surrounding conditions and which is basically the user’s design requirement. Triangular profile requires only about 68.8% as much metal as rectangular profile.

Capacity Enhancement of Fins In both (stip and triangular) fins, profile area varies as the cube of To double the heat flow, you use two fins or make one fin eight times as large. There is a virtue in using more number of small fins. In pin fin, profile volume varies as To double the heat flow, you use two fins or make one fin 3.17 times as large.

Pentium III Pentium II Pentium IV

Design and Optimization of Fin Arrays P M V Subbarao Mechanical Engineering Department IIT Delhi Millions of Ants are more Powerful than a Single Cobra……

Geometry of Fin Array tftf S b

Determination of Heat Transfer Coefficient S

Optimum spacing b

Optimum Natural Convection Array  From Elenbaas (1942):  For an array of optimally spaced fins:

Towards an Optimum Array of Optimum Fins Heat flow from each optimum fin: With the h for Optimum Spacing: With the Interfin Spacing

Industrial Practice Define the thermal resistance of the heat sink is given by

Selection Curves

Forced Convection Heat Sinks  Analytical modeling  Maximization of heat dissipation  Least-material optimization  Design for manufacture

Design Calculations for Fin Arrays – Thermal Resistance In order to select the appropriate heat sink, the thermal designer must first determine the maximum allowable heat sink thermal resistance. To do this it is necessary to know the maximum allowable module case temperature, T case, the module power dissipation, P mod, and the thermal resistance at the module-to- heat sink interface, R int. The maximum allowable temperature at the heat sink attachment surface, T base, is given by

The maximum allowable heat sink resistance, R max, is then given by The thermal resistance of the heat sink is given by parameters the gap, b, between the fins may be determined from

Constant air velocity

Constant volumetric flow rate

Heat Sink Pressure Drop To determine the air flow rate it is necessary to estimate the heat sink pressure drop as a function of flow rate and match it to a curve of fan pressure drop versus flow rate. A method to do this, using equations presented here. As in the previous article, the heat sink geometry and nomenclature used is that shown Figure 1.

Pressure Drop Curves

Effect of number of fins and fin height

Thermal Resistance

Closure a fan with a different fan curve is employed, the flow rates will change and the optimum heat sink design point may change as well. The important point is that to determine how a heat sink will perform in a given application both its heat transfer and pressure drop characteristics must be considered in concert with the pressure-flow characteristics of the fan that will be used. It should also be noted that an underlying assumption is that all the flow delivered by the fan is forced to go through the channels formed between the heat sink fins. Unfortunately this is often not the case and much of the air flow delivered by the fan will take the flow path of least resistance bypassing the heat sink. Under such circumstances the amount of flow bypass must be estimated in order to determine the heat sink performance.