Why is this hard to read

Unrelated vs. Related Color Unrelated color: color perceived to belong to an area in isolation (CIE 17.4) Related color: color perceived to belong to an area seen in relation to other colors (CIE 17.4)

Illusory contour Shape, as well as color, depends on surround Most neural processing is about differences

Illusory contour

CS 768 Color Science Perceiving color Describing color Modeling color Measuring color Reproducing color

Spectral measurement Measurement p( ) of the power (or energy, which is power x time ) of a light source as a function of wavelength Usually relative to p(560nm) Visible light nm

Retinal line spread function retinal position relative intensity

Linearity additivity of response (superposition) r(m 1 +m 2 )=r(m 1 )+r(m 2 ) scaling (homogeneity) r(  m)=  r(m) r(m 1 (x,y)+m 2 (x,y))= r(m 1 )(x,y)+r(m 2 )(x,y)= (r(m 1 )+r(m 2 ))(x,y) r(  m(x,y))=  r(m)(x,y) retinal intensity monitor intensity

Non-linearity

Ganglion Bipolar Amacrine Rod Cone Epithelium Optic nerve Retinal cross section Light Horizontal

Visual pathways Three major stages –Retina –LGN –Visual cortex –Visual cortex is further subdivided

Optic nerve 130 million photoreceptors feed 1 million ganglion cells whose output is the optic nerve. Optic nerve feeds the Lateral Geniculate Nucleus approximately 1-1 LGN feeds area V1 of visual cortex in complex ways.

Photoreceptors Cones - –respond in high (photopic) light –differing wavelength responses (3 types) –single cones feed retinal ganglion cells so give high spatial resolution but low sensitivity –highest sampling rate at fovea

Photoreceptors Rods –respond in low (scotopic) light –none in fovea try to foveate a dim star—it will disappear –one type of spectral response –several hundred feed each ganglion cell so give high sensitivity but low spatial resolution

Luminance Light intensity per unit area at the eye Measured in candelas/m 2 (in cd/m 2 ) Typical ambient luminance levels (in cd/m 2 ): –starlight –moonlight –indoor lighting 10 2 –sunlight 10 5 –max intensity of common CRT monitors 10 ^2 From Wandell, Useful Numbers in Vision Science

Rods and cones Rods saturate at 100 cd/m 2 so only cones work at high (photopic) light levels All rods have the same spectral sensitivity Low light condition is called scotopic Three cone types differ in spectral sensitivity and somewhat in spatial distribution.

Cones L (long wave), M (medium), S (short) –describes sensitivity curves. “Red”, “Green”, “Blue” is a misnomer. See spectral sensitivity.

Receptive fields Each neuron in the visual pathway sees a specific part of visual space, called its receptive field Retinal and LGN rf’s are circular, with opponency; Cortical are oriented and sometimes shape specific On center rfRed-Green LGN rf Oriented Cortical rf

Channels: Visual Pathways subdivided Channels Magno –Color-blind –Fast time response –High contrast sensitivity –Low spatial resolution Parvo –Color selective –Slow time response –Low contrast sensitivity –High spatial resolution Video coding implications Magno –Separate color from b&w –Need fast contrast changes (60Hz) –Keep fine shading in big areas –(Definition) Parvo –Separate color from b&w –Slow color changes OK (40 hz) –Omit fine shading in small areas –(Definition) (Not obvious yet) pattern detail can be all in b&w channel

Trichromacy Helmholtz thought three separate images went forward, R, G, B. Wrong because retinal processing combines them in opponent channels. Hering proposed opponent models, close to right.

Opponent Models Three channels leave the retina: –Red-Green (L-M+S = L-(M-S)) –Yellow-Blue(L+M-S) –Achromatic (L+M+S) Note that chromatic channels can have negative response (inhibition). This is difficult to model with light.

+- +

Log Spatial Frequency (cpd) Contrast Sensitivity Luminance Red-Green Blue-Yellow

Color matching Grassman laws of linearity: (     )(   (   (   Hence for any stimulus s( ) and response r( ), total response is integral of s( ) r( ), taken over all or approximately  s( )r( )

Primary lights Test light Bipartite white screen Surround field Test lightPrimary lights Subject Surround light

Color Matching Spectra of primary lights s 1 ( ), s 2 ( ), s 3 ( ) Subject’s task: find c 1, c 2, c 3, such that c 1 s 1 ( )+c 2 s 2 ( )+c 3 s 3 ( ) matches test light. Problems (depending on s i ( )) –[c 1,c 2,c 3 ] is not unique (“metamer”) –may require some c i <0 (“negative power”)

Color Matching Suppose three monochromatic primaries r,g,b at , , nm and a 10° field (Styles and Burch 1959). For any monochromatic light t( ) at  find scalars R=R(  G=G(  B=B(  such that t( ) = R(  r  G(  g  B(  b R( ,  G( ,  B(  are the color matching functions based on r,g,b.

Color matching Grassman laws of linearity: (     )(   (   (   Hence for any stimulus s( ) and response r( ), total response is integral of s( ) r( ), taken over all or approximately  s( )r( )

Color matching What about three monochromatic lights? M( ) = R* R ( ) + G* G ( ) + B* B ( ) Metamers possible good: RGB functions are like cone response bad: Can’t match all visible lights with any triple of monochromatic lights. Need to add some of primaries to the matched light

Primary lights Test light Bipartite white screen Surround field Test lightPrimary lights Subject Surround light

Color matching Solution: CIE XYZ basis functions

Color matching Note Y is V( ) None of these are lights Euclidean distance in RGB and in XYZ is not perceptually useful. Nothing about color appearance

XYZ problems No correlation to perceptual chromatic differences X-Z not related to color names or daylight spectral colors One solution: chromaticity

Chromaticity Diagrams x=X/(X+Y+Z) y=Y/(X+Y+Z) z=Z/(X+Y+Z) Perspective projection on X-Y plane z=1-(x-y), so really 2-d Can recover X,Y,Z given x,y and on XYZ, usually Y since it is luminance

Chromaticity Diagrams No color appearance info since no luminance info. No accounting for chromatic adaptation. Widely misused, including for color gamuts.

Some gamuts SWOP ENCAD GA ink

MacAdam Ellipses JND of chromaticity Bipartite equiluminant color matching to a given stimulus. Depends on chromaticity both in magnitude and direction.

MacAdam Ellipses For each observer, high correlation to variance of repeated color matches in direction, shape and size –2-d normal distributions are ellipses –neural noise? See Wysecki and Styles, Fig 1(5.4.1) p. 307

MacAdam Ellipses JND of chromaticity –Weak inter-observer correlation in size, shape, orientation. No explanation in Wysecki and Stiles 1982 More modern models that can normalize to observer?

MacAdam Ellipses JND of chromaticity –Extension to varying luminence: ellipsoids in XYZ space which project appropriately for fixed luminence

MacAdam Ellipses JND of chromaticity –Technology applications: Bit stealing: points inside chromatic JND ellipsoid are not distinguishable chromatically but may be above luminance JND. Using those points in RGB space can thus increase the luminance resolution. In turn, this has appearance of increased spatial resolution (“anti-aliasing”) Microsoft ClearType. See and

CIELab L* = 116 f(Y/Y n )-16 a* = 500[f(X/X n ) – f(Y/Y n )] b* = 200[f(Y/Y n ) –f(Z/Z n )] where X n,Y n,Z n are the CIE XYZ coordinates of the reference white point. f(z) = z 1/3 if z> f(z)=7.787z+16/116 otherwise L* is relative achromatic value, i.e. lightness a* is relative greenness-redness b* is relative blueness-yellowness

CIELab L* = 116 f(Y/Y n )-16 a* = 500[f(X/X n ) – f(Y/Y n )] b* = 200[f(Y/Y n ) –f(Z/Z n )] where X n,Y n,Z n are the CIE XYZ coordinates of the reference white point. f(z) = z 1/3 if z> f(z)=7.787z+16/116 otherwise

CIELab L* = 116 f(Y/Y n )-16 a* = 500[f(X/X n ) – f(Y/Y n )] b* = 200[f(Y/Y n ) –f(Z/Z n )] where X n,Y n,Z n are the CIE XYZ coordinates of the reference white point. f(z) = z 1/3 if z> f(z)=7.787z+16/116 otherwise C* ab = sqrt(a* 2 +b* 2 ) corresponds to perception of chroma (colorfulness). hue angle h ab =tan -1 (b*/a*) corresponds to hue perception. L* corresponds to lightness perception Euclidean distance in Lab space is fairly correlated to color matching and color distance judgements under many conditions. Good correspondence to Munsell distances.

a*>0 redder a*<0 greener b*>0 yellower b*<0 bluer chroma hue lightness

Complementary Colors c1 and c2 are complementary hues if they sum to the whitepoint. Not all spectral (i.e. monochromatic) colors have complements. See chromaticity diagram. See Photoshop Lab interface.

CIELab defects Perceptual lines of constant hue are curved in a*-b* plane, especially for red and blue hues (Fairchiled Fig 10.5) Doesn’t predict chromatic adaptation well without modification Axes are not exactly perceptual unique r,y,g,b hues. Under D65, these are approx 24°, 90°,162°,246° rather than 0°, 90°, 180°, 270° (Fairchild)

CIELab color difference model  E*=sqrt(  L* 2 +  a* 2 +  b* 2 ) –May be in the same L*a*b* space or to different white points (but both wp’s normalized to same max Y, usually Y=100). –Typical observer reports match for  E* in range 2.5 – 20, but for simple patches, 2.5 is perceptible difference (Fairchild)

Viewing Conditions Illuminant matters. Fairchild Table 7-1 shows  E* using two different illuminants. Consider a source under an illuminant with SPD T( ). If color at a pixel p has spectral distribution p(  and reflectance factor of screen is r(  then SPD at retina is r( )T( )+p( ). Typically r(  is constant, near 1, and diffuse.

Color ordering systems Want system in which finite set of colors vary along several (usually three) axes in a perceptually uniform way. Several candidates, with varying success –Munsell Spectra available at Finnish site –NCS –OSA Uniform Color Scales System –…–…

Color ordering systems CIE L*a*b* still not faithful model, e.g. contours of constant Munsell chroma are not perfect circles in L*a*b* space. See Fairchild Fig 10-4, Berns p. 69.

Effect of viewing conditions Impact of measurement geometry on Lab –Need illumination and viewing angle standards –Need reflection descriptions for opaque material, transmission descriptions for translucent

Reflection geometry diffuse specular

Reflection geometry Semi-glossy glossy

Reflection geometry Semi-glossy glossy

Some standard measurement geometries d/8:i diffuse illumination, 8° view, specular component included d/8:e as above, specular component excluded d/d:i diffuse illumination and viewing, specular component included 45/0 45° illumination, 0° view

Viewing comparison L*C*h EE d/8:i / d/8:e Measurement differences of a semi-gloss tile under different viewing conditions (Berns, p. 86).  E is vs. d/8:i. Data are for Lab.

L*u*v* CIE u' v' chromaticity coordinates: u'=4X/(X+15Y+3Z)= 4x/(-2+12y+3) v'=9Y/(X+15Y+3Z)=9y/(-2+12y+3) Gives straighter lines of constant Munsell chroma (See figures on p. 64 of Berns). L* = 116(Y/Y n ) 1/3 – 16 u* = 13L*(u' – u n ') v* = 13L*(v'-v n ')

L*u*v* L* = 116(Y/Y n ) 1/3 – 16 u* = 13L*(u' – u n ') v* = 13L*(v'-v n ') u n ', v n ' values for whitepoint

Models for color differences Euclidean metric in CIELab (or CIELuv) space not very predictive. Need some weighting  V = (1/k E) )[(  L*)/k L S L ) 2 +(  C  */k C S C ) 2 +(  H  */k H S H ) 2 ] 1/2  = uv or ab according to whether using L*a*b* or L*u*v* The k's are parameters fit to the data. The S's are functions of the underlying variable, estimated from data.

Models for color differences  E* 94 k L = k C = k H = 1 S L = 1 S C = C* ab S H = C* ab Fitting with one more parameter for scaling gives good predictions. Berns p 125.

Color constancy Color difference models such as previous have been used to predict color inconstancy under change of illumination. Berns p. 214.

Other color appearance phenomena Models still under investigation to account for: –Colorfulness (perceptual attribute of chroma) increases with luminance ("Hunt effect") –Brightness contrast (perceptual attribute of lightness difference) increases with luminance –Chromatic adaptation

Color Gamuts Gamut: the range of colors that are viewable under stated conditions Usually given on chromaticity diagram –This is bad because it normalizes for lightness, but the gamut may depend on lightness. –Should really be given in a 3d color space –L*a*b* is usual, but has some defects to be discussed later

Color Gamut Limitations 1.CIE XYZ underlies everything –this permits unrealizable colors, but usually "gamut" means restricted to the visible spectrum locus in chromaticity diagram 2.Gamut can depend on luminance –usually on illuminant relative luminance, i.e. Y/Y n

Color Gamut Limitations Surface colors –reflectance varies with gloss. Generally high gloss increases lightness and generally lightness reduces gamut (see figures in Berns, p. 145 ff) Stricter performance requirements often reduce gamut –e.g. require long term fade resistance

Color Gamut Limitations Physical limitations of colorants and illuminants –Specific set of colorants and illuminants are available. For surface coloring we can not realize arbitrary XYZ values even within the chromaticity spectral locus Economic factors –Color may be available but expense not justified