Chapter 16 – Stainless Steels Gateway Arch in St Louis – 304 series SS F-35 Joint Strike Fighter (JSF) Lightning II, built by Lockheed Martin – airframe.

Slides:



Advertisements
Similar presentations
Metals and Alloys. Alloys Two definitions Combination of two or more elements Combination of two or more metallic elements Metallurgical Commercial.
Advertisements

HEAT TREATMENT OF STEEL
Production Technology (IND 006) Preparatory Year, Faculty of Engineering, Fayoum University Dr. Ahmed Salah Abou Taleb Lecturer, Industrial Engineering.
UNIT 3: Metal Alloys Unit 3 Copyright © 2012 MDIS. All rights reserved. 1 Manufacturing Engineering.
D AY 17 S TEELS AND S TAINLESS S TEEL. P RECIPITATION H ARDENING – S TEELS Key to all of this: Very Low Carbon Content. Various amounts of alloying metals.
Group 2 Steels: Medium Carbon Alloy Steels (0.25 – 0.55 %C)
Properties and Applications
Ferrous Metals and Alloys
Stainless Steel High Ni & Cr Content Low (Controlled) Interstitials Austenitic Nitrogen Strengthened Austenitic Martensitic Ferritic Precipitation Hardened.
Mechanical & Aerospace Engineering West Virginia University Strengthening by Phase Transformation.
Chapter 5 Ferrous Alloys.
Section 3.3 Ferrous and Nonferrous Metals
Specialty Steel Products ESP Specialty Steel Products Commitment to our Customers.
STAINLESS STEEL PIPES. WHAT IS STAINLESS STEEL TYPICAL PROPERTIES Stainless steels are alloys containing iron, relatively low carbon, a minimum 10.5%
Stainless Steels Stainless steels are iron base alloys that contain a minimum of approximately 12% Cr, the amount needed to prevent the formation of rust.
Nickel to Stainless Dissimilar Metal Welding
STAINLESS STEEL AS REINFORCEMENT BY- Bhrugesh Patel SD-1210 STRUCTURAL DEPARTMENT CEPT UNIVERSITY.
Conceptual Designs. Most Commonly used Metals Plain carbon steels –Available in all structural forms, thin sheets, coated or uncoated, cold formed, hot.
Chapter 14 – Carbon and Alloy Steels
Metals Part 2 Manufacturing Processes, MET 1311 Dr Simin Nasseri
PALESTINE UNIVERSITY BUILDING MATERIAL chapter No.#4 Steel.
By Usanee thanawutsakunchai Sasichai jaithum
Group 4 Steels: Tools Steels and Their Uses High speed (HS) tools steels are used for high cutting speeds such as drills, mill cutters, taps and others.
© ATI Allegheny Ludlum Stainless Steels in the Process Industries John F. Grubb ATI Allegheny Ludlum October 2009.
Selection Criteria Properties Availability Cost Manufacturability
Nonferrous Metals and Alloys
Chapter 9 Characteristics of Metallic Materials. Objectives Four major classifications – ferrous,non ferrous, high temperature super alloy, and refractories.
Unit 3 effect of alloying additions on steel. Austenite-forming elements The elements C, Ni and Mn are the most important ones in this group. Sufficiently.
Metallic Materials.  Types of metallic Materials * Aluminum * Brass * Bronze * Stainless Steel * Carbon Steel * Copper.
ME Session #5 Selection of term projects Assignment#4 : Review of manufacturing processes Presentations of PDS work Material selection Questions.
B. Titanium-based Alloys Titanium is hcp at room temperature – and transform to the bcc structure on heating to 883 o C. Alloying elements are added to.
November 2014  WHAT IS STAINLESS STEEL?  WHY CHOOSE STAINLESS?  PRODUCT FORMS  HOW IS IT MADE?  5 CLASSES OF STAINLESS  ANNEALING & INTERGRANULAR.
Steel Stainless Steel Cast Iron Copper/Brass Aluminum
EBB113 METALS ALLOYS. Metal Alloys Ferrous SteelCast Iron Low AlloyHigh Alloy Non Ferrous Fe 3 C cementite
Series Stainless Steels A look at the grades, properties and applications.
Metal Alloys Formation
Numbering and Classification of Non-ferrous metals
Metallurgy: Identifying Metals
HEAT TREATMENT OF STEEL
1 Teaching Innovation - Entrepreneurial - Global The Centre for Technology enabled Teaching & Learning, N Y S S, India DTEL DTEL (Department for Technology.
Properties and Applications
Metals can be either ferrous or non-ferrous. Ferrous metals contain iron while non-ferrous metals do not.Metals can be either ferrous or non-ferrous.
Ferrous metals LAXMI INSTITUTE OF TECHNOLOGY SARIGAM LAXMI INSTITUTE OF TECHNOLOGY SARIGAM GUIDED BY, PREPARED BY, MR. ANKUR VASAVA ASST.PROFFESOR, MECH.ENGG.DEPT,
Metal Types. Objectives Know the types of metals and examples of them Know the types of metals and examples of them.
Physical Metallurgy EBB222 Stainless steel.
DR KAFEEL AHMED Cast iron Properties 1.Strength 2.Hardness 3.Brittleness 4.Stiffness Depends upon 1.Alloying elements 2.Annealing.
K . J . INSTITUTE OF ENGINEERING & TECHNOLOGY (064)
C.K.PITHAWALA COLLEGE OF ENGG. & TECHNOLGY Presented By :- Group No :- 6 1 DereViral M Rajwadwala Faizal Mavdiya Yash
Nonferrous Metals & Alloys. Nonferrous Metals Ferrous Alloys – alloys contain iron Nonferrous Metals – metals do not contain iron such as Copper (Cu),
1 Classification Metals can be divided into 2 groups Metals Ferrous MetalsNon- Ferrous Metals IronAluminum Low Carbon SteelCopper Medium Carbon SteelBrass.
STEEL & ALLOY STEEL STEEL- %C TO 2.0 % AS PER I-C DIAG.
FERROUS AND NON FERROUS ALLOYS
STAINLESS STEEL AND SPRING STEEL.
4/27/2018 2:57 AM TOOL STEELS © 2007 Microsoft Corporation. All rights reserved. Microsoft, Windows, Windows Vista and other product names are or may.
SURGICAL SUTURES AND NEEDLES
What are stainless steels?
Implant: مادة سنية / د . زينة ثاني اسنان موصل 12 / 4 / 2016
FERROUS AND NON FERROUS ALLOYS
The Consequence of Element Alloying.
Heat treatment of steel
Group 2 Steels: Medium Carbon Alloy Steels (0.25 – 0.55 %C)
Chapter 6: Metals & alloys Part 2
Ferrous Metals.
Four Types of Engineering Materials
CHAPTER 9 Engineering Alloys 1.
MME293: Lecture 16 FERROUS ALLOYS: ( Low and High alloy steels)
ME Session #5 Selection of term projects
Carbon Steel, Low Alloy Steels
Selection Criteria Properties Availability Cost
Gateway Arch in St Louis – 304 series SS F-35 Joint Strike Fighter (JSF) Lightning II, built by Lockheed Martin – airframe 17-7 PH – 600 series SS Prepared.
Presentation transcript:

Chapter 16 – Stainless Steels Gateway Arch in St Louis – 304 series SS F-35 Joint Strike Fighter (JSF) Lightning II, built by Lockheed Martin – airframe 17-7 PH – 600 series SS

Key Points: Alloy steels containing at least 10% Cr are SS. Contain sufficient amount of Cr that they are considered high alloy. Corrosion resistance is imparted by the formation of a passivation layer characterized by: –Insoluble chromium oxide film on the surface of the metal - (Cr 2 O 3 ). –Develops when exposed to oxygen and impervious to water and air. –Layer is too thin to be visible –Quickly reforms when damaged –Susceptible to sensitization, pitting, crevice corrosion and acidic environments. –Passivation can be improved by adding nickel, molybdenum and vanadium.

Where Used? Food industry (cookware, flatware, food transport and storage tankers) due to its corrosion resistance and antibacterial properties. Surgical equipment Aerospace High end automotive, industrial, etc.

Also: strong, tough, high operating temperatures, thermal conductivity = 1/3 that of carbon steels, difficult to machine, more expensive than carbon steel ($5/lb vs $0.5/lb).

Key Points: SS can also be classified by crystal structure (austenitic, ferritic, martensitic) Best corrosion resistance (CR): Austenitic (25% Cr) Middle CR : Ferritic (15% Cr), Least CR: Martensitic (12% Cr), but strongest

Key Points: Over 150 grades of SS available, usually categorized into 5 series containing alloys w/ similar properties. AISI classes for SS: –200 series = chromium, nickel,manganese (austenitic) –300 series = chromium, nickel (austenitic) –400 series = chromium only (ferritic) –500 series = low chromium <12% (martensitic) –600 series = Precipitation hardened series (17-7PH, 17-7 PH, 15-5PH)

200/300 Series SS (Austenitic): Most common SS (roughly 70% of total SS production) Used for flatware, cookware, architecture, automotive, etc. 0.15% C (max), 16% Cr (min) and Ni or Manganese Austenitic, High strength, best corrosion resistance. High temp capability up to 1200 F. non-magnetic, good ductility and toughness, not hardenable by heat treatment, but they can be strengthened via cold working, best corrosion resistance but most expensive, corrosive in hydrochloric acid. General use where corrosion resistance is needed. Typical alloy 18% Cr and 10% Ni = commonly known as 18/10 stainless Also have low carbon version of Austenitic SS (316L or 304L) used to avoid corrosion problem caused by welding, L = carbon content < 0.03%

300 Series—austenitic chromium-nickel alloys  Type 301—highly ductile, for formed products. Also hardens rapidly during mechanical working. Good weldability. Better wear resistance and fatigue strength than 304.  Type 302—same corrosion resistance as 304, with slightly higher strength due to additional carbon.  Type 303—free machining version of 304 via addition of sulfur and phosphorus. Also referred to as "A1" in accordance with ISO [10]free machiningsulfurphosphorusISO 3506 [10]  Type 304—the most common grade; the classic 18/8 stainless steel. Also referred to as "A2" in accordance with ISO [10]ISO 3506 [10]  Type 304L— same as the 304 grade but contains less carbon to increase weldability. Is slightly weaker than 304.  Type 304LN—same as 304L, but also nitrogen is added to obtain a much higher yield and tensile strength than 304L.  Type 308—used as the filler metal when welding 304  Type 309—better temperature resistance than 304, also sometimes used as filler metal when welding dissimilar steels, along with inconel. inconel  Type 316—the second most common grade (after 304); for food and surgical stainless steel uses; alloy addition of molybdenum prevents specific forms of corrosion. It is also known as marine grade stainless steel due to its increased resistance to chloride corrosion compared to type is often used for building nuclear reprocessing plants. 316L is an extra low carbon grade of 316, generally used in stainless steel watches and marine applications due to its high resistance to corrosion. Also referred to as "A4" in accordance with ISO [10] 316Ti includes titanium for heat resistance, therefore it is used in flexible chimney liners.surgical stainless steelnuclear reprocessing ISO 3506 [10]  Type 321—similar to 304 but lower risk of weld decay due to addition of titanium. See also 347 with addition of niobium for desensitization during welding.weld decay Common 300 series grades of SS:

400 Series SS (Ferritic): Ferritic, Automotive trim, chemical processing, blades, knives, springs, ball bearings, surgical instruments. Can be heat treated! Contain between 10.5% and 27% Cr, little Ni and usually molybdenum. –Common grades: 18Cr-2Mo, 26Cr-1Mo, 29Cr-4Mo, and 29Cr-4Mo-2Ni Magnetic (high in Fe content) and may rust due to iron content. Lower strength vs 300 series austenitic grades Cheap

400 common alloys  Type 405— ferritic for welding applications  Type 408—heat-resistant; poor corrosion resistance; 11% chromium, 8% nickel.  Type 409—cheapest type; used for automobile exhausts; ferritic (iron/chromium only).automobileexhausts  Type 410—martensitic (high-strength iron/chromium). Wear-resistant, but less corrosion- resistant.  Type 416—easy to machine due to additional sulfur  Type 420—Cutlery Grade martensitic; similar to the Brearley's original rustless steel. Excellent polishability.  Type 430—decorative, e.g., for automotive trim; ferritic. Good formability, but with reduced temperature and corrosion resistance.  Type 440—a higher grade of cutlery steel, with more carbon, allowing for much better edge retention when properly heat-treated. It can be hardened to approximately Rockwell 58 hardness, making it one of the hardest stainless steels. Due to its toughness and relatively low cost, most display-only and replica swords or knives are made of 440 stainless. Also known as razor blade steel. Available in four grades: 440A, 440B, 440C, and the uncommon 440F (free machinable). 440A, having the least amount of carbon in it, is the most stain-resistant; 440C, having the most, is the strongest and is usually considered more desirable in knifemaking than 440A, except for diving or other salt-water applications.Rockwell  Type 446—For elevated temperature service Common 400 series grades of SS:

500 Series SS (Martensitic): Not as corrosion resistant as the other classes but extremely strong and tough as well as machineable and can be hardened via heat treat. High strength structural applications (Su up to 300 ksi) – nuclear plants, ships, steel turbine blades, tools, etc. Magnetic

600 Series Precipitation Hardening Martensitic SS: Have corrosion resistance comporable to 300 series austentic grades but can be precipitation hardened for increased strength! Key: High strength + corrosion resistance BOTH. Why? Aerospace industry – defense budgets determined 2% of GDP spent dealing with corrosion so developed high strength corrosion resistant steel to replace alloy steels. Lockheed-Martin Joint Striker Fighter – 1 st aircraft to use PH SS for entire airframe. Common Grades: – 630 grade = 17-4 PH (17% Cr, 4% Ni), –17-4 PH, –15-5 PH

NITRONIC 50: Tradenames Nitronic 50, XM-19 General Properties Density lb/in^3 Price USD/lb Composition overview Composition (summary) Fe/22Cr/13Ni/5Mn/2.5Mo BaseFe (Iron) Composition detail (metals, ceramics and glasses) Al (aluminum)0-0.02% B (boron)8e % C (carbon)0-0.06% Cr (chromium) % Cu (copper)0-0.75% Fe (iron) % Mn (manganese)4-6% Mo (molybdenum)1.5-3% N (nitrogen) % Nb (niobium) % Ni (nickel) % P (phosphorus)0-0.04% S (sulfur)0-0.03% Si (silicon)0-1% Sn (tin)0-0.03% Ta (tantalum)0-0.1% V (vanadium) % W (tungsten)0-0.15% Mechanical properties Young's modulus ^6 psi Flexural modulus* ^6 psi Shear modulus ^6 psi Bulk modulus ^6 psi Poisson's ratio Shape factor1 Yield strength (elastic limit) ksi Tensile strength ksi Elongation7-23% strain Also, super alloys (Inconel), NiCr High End Stainless (Nuclear Industry)