Lets Build A Gable Roof Created by the:- Carpentry & Joinery Section Granville & Chullora Technical College.

Slides:

Advertisements

Similar presentations

Roof Trusses Created By M.S.Martin 11/04, reviewed 11/05, reviewed 11/07.

Advertisements

Construction Explanation.

Roofs are one of a building’s primary elements and play a major part in giving a building its character. There are several different types of roof in.

Introduction to Pitched Roof Framing

Roof Framing A Quick Primer

Flat Roof & Introduction to Gable Roof

CEILING FRAMES Created by Michael Martin March 2004 / Revised Feb 2007.

CEILING FRAMES Created by Michael Martin March 2004

Gable Roofs and Components

Erecting Roof Trusses - Gable

Gable Ends, Verge, Eaves & Erection of Gable Roofs

Ceilings & Basic Roofing

Flat Roofs & Introduction to Gable Roofs

HIP ROOFS Created BY Michael Martin July 2004 / revised may 2007 / reviewed & updated March 2010.

Roof Construction By Drew Kelly Roof Construction Basics  Roof construction is the single most important structure on your home  Roofs provide.

Gable Roof BCGCA3007B.

Gable Roof BCGCA3007B.

Frame and Cornice Construction Sequence. Top Plate Double Plate Wall Stud (top half) Corner Post Frame and Cornice Construction Sequence Walls & Partitions.

Unit 44 Ceiling Framing Ceiling Joists • Laying Out Ceiling Frames • Constructing Ceiling Frames • Attic Scuttles • Constructing Flat Roof Ceilings.

Basic Roof Types and Roof Theory

QUINN TRUSS OPEN WEB JOIST SYSTEM TECHNICAL DETAILS.

Residential Framing Prints Unit 14.

Competency: Draw roof plans

Roof Framing Unit 33.

BCT 122 Roof Framing 1 Roof Framing Procedure Sequence.

Unit 1003 Building methods and construction technology © Pearson Education 2010 Printing and photocopying permitted Learning Outcome 3 Know about roof.

Created by Michael Martin 13/9/04 – Reviewed June 2010.

Gable Roof BCGCA3007B. Gable Roof Flush with no eaves Flush with raked eaves Boxed.

Copyright © by NCCER, Published by Pearson Education, Inc. Carpentry Fundamentals Level One Module National Center for Construction Education.

Gable, Gambrel, and Shed Roofs

Pattern Rafters & Calculations

Michelle Perticarari Rebeca Peña

Roof Types, Components & Terminology

Flat Roofs & Introduction to Gable Roofs Ref: M. S. Martin / March 2004 / Reviewed & Combined March 2007.

Structural Components

Roof and Ceiling Framing

Gable Roof BCGCA3007B.

By: Caleb VanderWal.  Mix cement  Dig hole at least 24” into the ground  Poor cement in ground with poles  Wait 2-3 days (if you don’t wait that long.

BUILDING THE FRAME Walls are constructed in sections, lying down on the floor platform and then tilted up into position. Fundamentals of Building Construction,

Wall Framing Grimsby Secondary School Technology Dept.

Ag Construction Studs Vertical framing boards are called.

Table of Contents Unit 1- Understand the Problem Unit 2- Gather Information Unit 3- Develop Solutions Unit 4- Implement A Solution Unit 5- Test and Evaluate.

1 FRENCH RED CROSS in Grenada CONSTRUCTION OF WOODEN HOUSES ACCORDING TO STANDARDS Tel: / Sugar Mill, St George’s.

Roof Types, Components & Terminology

Wall and Ceiling Construction

Lecture 15 - Timber Wall Framing Example

After the roof design is selected, the next decision is the type of roof construction-- trusses or stick built. Trusses. Less labor to install trusses.

National Center for Construction Education and Research Carpentry, Level 1 Copyright © by the NCCER, Published by Pearson Education, Inc. FIGURE 6- 1 Types.

Designing and constructing a traditional half span hipped end roof  Roof to a domestic extension.

Estimating Hip Roofs.

ARCH 330 Fall 2008 Third Set Rough Carpentry Wall, Floor & Roof Systems.

Drafting 2 (Arch) Quiz Review #5

Pitched Roof By PATEL ANKITKUMAR H.

ROOFING BCGCA3007B.

CARPENTRY By: Jason Burkhart. The installation of your floor system will depend on the design of your house. The guidelines we will use are 24ft wide.

Framing Vocabulary Stud: upright beams in the framework of a building

Framing Agriculture Structures

Gable Roof BCGCA3007B.

Framing Agriculture Structures

Competency: Draw roof plans

Project Design & Construction

Competency: Draw roof plans

Vocab. Vocab Wall Layout Floor Layout Ceiling Layout.

Wall and Ceiling Construction

Rafters Interlocking Tiles Wall plate Fascia board Barge board fixed

Queen Post Truss Queen post trusses are not common in modern construction but they are still used. The example on the right shows exposed queen post trusses.

TRADA trusses TRADA trusses may look complicated but if you run through this sequence a couple of times the construction should be easier to understand.

Couple Roof ridge wall plate.

Competency: Draw roof plans

Presentation transcript:

Lets Build A Gable Roof Created by the:- Carpentry & Joinery Section Granville & Chullora Technical College

Plan View Gable Roof Construction This is a plan view of a gable roof. To build this roof certain stages must happen to successfully complete correctly and safely.

Plan View Gable Roof Construction 1.The bases or top plate dimensions are 3.0m X 4.0m 2.Measure from the centre of the top plates out at 450 centers. 3.Mark ceiling joists and rafters on the top plate mm 3000 mm Center line

Plan View Gable Roof Construction 1.Place ceiling joists in position & fix down. This protects you or your mate from falling off of ceiling frame because of racking. 2.Place ceiling trimmers in position & fix

Plan View Gable Roof Construction 1.Place hanger beam in position but don’t forget to brace & plum the hanger before you fix the ceiling joists to it. 2.A plank next to the hanger will help you in fixing the hanger safely. Brace for hanger

1.Measure and cut ridge beam & place on top of the hanger beam. 2.Cut pattern rafter & use it to cut common rafters. 3.Fix centering rafters into position and lift ridge beam into place.

1.Plum rafters & brace ridge. This brace also stops wind load from pushing the finished roof over. It must conform with the B.C.A. 2.Place common rafters into position & fix.

1.Place pitching plate into position then outriggers will sit on top and support the barge rafter. 2.The outriggers must conform with the B.C.A in the sense that the counter lever is 2/3 inside and 1/3 outside the pitching plate. 1/32/3

1. Brace roof using hoop iron or speed brace material & once again it must conform with the B.C.A. 2. Place Painted fascia & painted barge board to finish the work. Don’t forget the bell cast for roof material

Gable Roof  Safety first ( you are working at height)  Don’t cut any timber that is painted  Use triple grips & screws for fixing.  Efficiency in building will make the task easier.  Clean up at the end of the day must be done safely & correctly  When in doubt ask the teacher !!!!!!!