RET 2414L Pulmonary Function Testing Module 6.0 Arterial Blood Gases - Sampling, Equipment, Calibration, and Quality Control RET 2414L Pulmonary Function Testing Module 6.0

Arterial Blood Gases Equipment Arterial Blood Gas (ABG) Kit Prepackaged and contains all necessary equipment 3 – 5 cc syringe Pre-heparinized 22ga x 2 needle Alcohol swap Gauze pad Biohazard bag Misc. items

ABG Specimen Collection/Handling Site Selection

ABG Specimen Collection/Handling Site Selection Radial Artery - 45 insertion angle Requires modified Allen’s test for collateral circulation Brachial Artery - 60 - 90 insertion angle Femoral Artery - 90 insertion angle Dorsalis Pedis Artery Site must be adequately compressed until clotted Approximately 5 minutes Patients receiving anticoagulation therapy take longer

ABG Specimen Collection/Handling Hazards Hematoma Arterial laceration Hemorrhage Vasovagal reaction Sympathetic nervous system response to pain Loss of limb

ABG Specimen Collection/Handling Blood gas specimen should collected anaerobically Expel air bubbles immediately In Vivo Values Air Contamination pH 7.40 7.45 PCO2 40 30 PO2 95 110

ABG Specimen Collection/Handling Blood gas specimen must be adequately anticoagulated Sodium heparin Lithium heparin (electrolytes) Sample volume should be 1 – 2 ml Each laboratory has its own protocol

ABG Specimen Collection/Handling Sample should be analyzed as soon as possible If iced sample can be stored Glass syringe – 1 hour Plastic syringe – 15 minutes Remember: Blood is living tissue that continues to consume O2 and produce CO2

ABG Specimen Collection/Handling Specimen should be adequately identified Patient name / ID number Date / Time Ordering physician Accession number Puncture site Oxygen adjunct and FiO2 Ventilator settings (if applicable)

ABG Specimen Collection/Handling Transport specimen to laboratory in a biohazard container Analyze specimen on an instrument that has been recently calibrated Temperature correct specimen in analyzer Increase in patient temp: PO2, PCO2, pH Decrease in patient temp: PO2, PCO2, pH

Arterial Blood Gases Equipment Blood Gas Analyzer Electrolyte Solution Electronic Circuitry Electrolyte Solution Electrodes

Arterial Blood Gases Electronic circuitry Equipment Takes electrical current changes produced in the electrodes and provides a visual display Electrolyte Solution Helps to promote chemical reactions and electrical current

pH, PCO2, PO2 Arterial Blood Gases Electrodes Equipment Utilized to measure values of ABG pH, PCO2, PO2 All other blood gas values are calculated

Arterial Blood Gases Sanz Electrode pH Electrode Equipment Consists of two electrodes: sampling/measuring electrode reference electrode and electrolyte solution

Arterial Blood Gases Sanz Electrode (pH) The pH electrode is a microelectrode, shown here with its plastic jacket. At the tip is a silver-silver chloride wire in a sealed-in buffer behind PH-sensitive quartz glass. The reference electrode contains a platinum wire in calomel paste that rests in a 20% KCL solution. The blood sample is introduced in such a way that it contacts the measuring electrode tip and the KCL. A voltmeter measure the potential difference across the sample, which is proportional to the pH

Arterial Blood Gases Severinghaus Electrode PCO2 Electrode Equipment May also be referred to as a modified Sanz electrode

Arterial Blood Gases Severinghaus Electrode (PCO2) The PCO2 electrode is a modified pH electrode. The electrode has a sealed-in buffer; an Ag-AgCl reference band is the other half-cell. The entire electrode is encased in Lucite jacket filled with bicarbonate electrolyte. The jacket is capped with a Teflon membrane that is permeable to CO2. A nylon mesh covers the pH-sensitive glass, acting as a spacer to maintain contact with the electrolyte. CO2 diffuses through the Teflon membrane, combines with electrolyte, and alter the pH. The change in pH is displayed as partial pressure of CO2.

Arterial Blood Gases Clark Electrode PO2 Electrode Equipment May also be referred to as a polarographic electrode Periodic/routing cleaning of the tip with pumice is required because polypropylene attracts protein

Arterial Blood Gases Clark Electrode (PO2) The PO2 electrode contains a platinum cathode and a silver anode. The electrode is polarized by applying a slightly negative voltage of approximately 630 mV. The tip is protected by a polypropylene membrane that allows O2 molecules to diffuse but prevents contamination of the platinum wire. O2 migrates to the cathode and is reduced, picking up free electrons that have come from the anode through a phosphate-potassium chloride electrolyte. Changes in the current flowing between the anode and cathode result from the amount of O2 reduced in the electrolyte and are proportional to partial pressure of O2.

Arterial Blood Gases Calibration Procedures To assure appropriate electronic function of the electrodes, calibration procedures are performed Performed automatically every 30 minutes by the ABG machine Performed on the pH, PCO2, PO2 electrodes Specific procedure for each electrode

Arterial Blood Gases Calibration Procedures 2-Point Calibration A “low” concentration and a “high” concentration is used at both ends of the physiological range to be measured Multiple-Point Calibration (3 or more points) Verifies whether the gas analyzer is linear or not

Arterial Blood Gases pH Electrode Calibration Procedures Uses two specific buffers with approximate values of: 6.840 buffer referred to as the zero point or low point buffer 7.384 buffer high point or slope point buffer

Arterial Blood Gases pH Electrode Calibration Procedures Each buffer is injected into the sample chamber, one at a time The values of the buffer that is injected, should be displayed on the ABG machine within a specific SD (standard deviation)

Arterial Blood Gases pH Electrode Calibration Procedures Standard deviation for pH is + .005 If value displayed is within the SD, machine is electronically calibrated If value displayed is outside of the SD, machine needs to be adjusted to assure electronic function

Arterial Blood Gases Calibration Procedures PO2 & PCO2 Electrode Uses two specific concentration of gases for each electrode with approximate concentrations of CO2 and O2 Uses two different tanks of gas to accomplish this

Arterial Blood Gases Calibration Procedures PO2 & PCO2 Electrode Tank One Low CO2 (5%) - balance High O2 (12% or 20%) Balance Nitrogen Tank Two High CO2 (10%) – slope O2 (0%)

Arterial Blood Gases Calibration Procedures PO2 & PCO2 Electrode Must convert tank concentration from % to mm Hg (PB – PH2O) x tank concentration = mm Hg (760 – 47) x 0.12 = 85.65 mm Hg

Arterial Blood Gases Calibration Procedures PO2 & PCO2 Electrode The values calculated for the CO2 and O2 concentration should be displayed on the ABG analyzer within a specific SD (standard deviation)

Arterial Blood Gases PO2 & PCO2 Electrode Calibration Procedures Standard deviation for PO2 and CO2 is + 0.5 If values displayed are within the SD, machine is electronically calibrated If value displayed is outside of the SD, machine needs to be adjusted to assure electronic function

Arterial Blood Gases Calibration Procedures Troubleshooting If the ABG machine will not calibrate, check: The buffers The mixed gases The electrode’s membrane The electrode itself

Arterial Blood Gases Quality Control Calibration vs. Quality Control Calibration is when the equipment is adjusted or corrected to match the control standards Quality Control testing must be performed on a regular basis to determine the accuracy and precision of the equipment against a known standard

Arterial Blood Gases Quality Control Accuracy vs. Precision Accuracy refers to the mean (average) value of several measurements Precision refers to how consistently the same measurement will produce the same results

Arterial Blood Gases Quality Control Must be run every shift Utilize a known concentration of gases and buffers in a vial of liquid Run three levels of QC Level 1 – Acidosis Level 2 – Normal Level 3 - Alkalosis

“KNOWN VALUE IN MUST EQUAL Arterial Blood Gases Quality Control “KNOWN VALUE IN MUST EQUAL KNOW VALUE OUT!”

Arterial Blood Gases Quality Control When QC is run it must be recorded and maintained onsite; in the ABG laboratory Must be available for review by State agencies on demand

Arterial Blood Gases Quality Control Plotting In control Trend Random Error Out of Control

Arterial Blood Gases Quality Control In control All QC runs are within the acceptable +SD

Arterial Blood Gases Quality Control Trend All QC runs within the acceptable +SD but trending towards one side of the SD

Arterial Blood Gases Quality Control Random Error All QC runs within the acceptable +SD except for one run

Arterial Blood Gases Quality Control Out of control Two or more QC runs are out of the acceptable +SD

Capnography Capnography is the continuous, noninvasive monitoring of expired CO2 and analysis of the single-breath CO2 waveform

Capnography Capnography is performed utilizing: Infrared analyzer CO and CO2 absorb infrared radiation

Capnography Capnography is performed utilizing: Infrared analyzer Requires accurate calibration 2 gas concentrations used Room air 5% CO2 mixture Inaccurate reading can occur when: Condensation of water in sample tubing, connectors, or sample chamber Flow changes after calibration Saturation of a desiccant column Long sampling lines can cause waveform damping