CribMaster™ AMS Toolbox

CribMaster Support Options http://www.cribmaster.com/vending.html ftp.ecribmaster.com/pub Videos - ftp.ecribmaster.com/pub/documentation/videos/ Technical Support 1-855-CRIB-CMS 1-855-274-2267 CribMaster Support portal – support@cribmaster.com

AMS ToolBox intro The original CribMaster ToolBox was the first of all the CribMaster vending solutions – 1992 Specs: 73”H x 39”W x 41.5” D, approx. 698lbs. unstocked (185.4 cm x 99.1 cm x 105.4 cm, approx. 317kg) Add 5.8” (15 cm) for pallet height 120 volt/60 Hz, 4 amps (North America) 240 volt/50 Hz, 2 amps (Europe) Temperature Range -4F to 140F (-20 to 60 Celsius) Humidity of 20% to 80% RH Non-Condensing Specific model is AMS 39 – 660 Possible 1,920 individual items. Coil size and pitch options – Many Options

Un-Crating the AMS Toolbox Fork Lift close to vending location Remove retaining clips Fork lift upward to remove pallet

Power and connectivity *

Power input components

Power switch

Power input components

coil size and pitch options Small Coil – 5, 7, 8, 9, 10, 12, 15, 18, 24, 32 Large Coil – 4, 5, 7, 9, 10, 12, 15 Dual Coil – 5, 7, 10, 12, 15, 24

coil pitch by Inches 4 Pitch = 4 ½” 12 Pitch = 1 ¾” 5 Pitch = 3 ¾”

coil pitch by Metric 4 = 114.30mm 12 = 44.450mm 5 = 95.250mm 24 = 19.050 9 = 50.800mm 32 = 12.700mm 10 = 47.625mm

Different types & sizes of coils

Different types & sizes of coils

Bin Naming Format <Crib #>-<Shelf #>-<Bin or Tray #> AMS Toolbox Bin Naming Bin Naming Format <Crib #>-<Shelf #>-<Bin or Tray #> Ex: 10-01-01 is located in Crib 10, Shelf 1, Bin/Tray 01

Sizing & Packaging are key! Methods and materials to help items dispense correctly: Rubber bands Plastic bags Roll and cuff gloves or sleeves, especially any glove with rubber or sticky surfaces Test with multiple items in coil to ensure total resistance is not greater than the motor(s) can dispense properly! Show Toolbox Packaging Video

INSTALLATION AND TRAINING RECEIVING ITEMS INTO THE AMS TOOLBOX ADJUSTING AND COUNTING ITEMS ISSUING ITEMS FROM THE AMS TOOLBOX

Replacing parts & Testing Removing Coils Removing Helix Adapter Removing Coil Wing/Plastic Triangle Replacing Motors Removing Tray/Drawer Removing Dividers Installing Riser Testing Coils: ATR9 Software and Internal Control Panel Show AMS Helix and Motor Configuration video

Steps for installing riser 1. Bracket in place

Steps for installing riser 2 Steps for installing riser 2. Slide the curved end of the Riser in first/Screw in the 2 screws to secure

Steps for installing riser 3. Completed riser

ATR Setup Add AMS Toolbox, NOT ToolboxMachine!

Troubleshooting Motors can be spun using the internal control panel. Motors can be spun using ADMIN / ADJUST / OPEN within CribMaster ATR. Motors can also be spun using a CribMaster Utility application called “SPIN”.

Troubleshooting Incorrect Item packing will ultimately lead to jams. Incorrect item sizing can lead to jams.