© Easy Guides Australia “Graders perform a wide variety of operations from moderate dozing work to precision grading.” Side Casting Mixing Trimming Shaping.

Slides:

Advertisements

Similar presentations

Ch 5 (Part II): Simple Machines

Advertisements

Lathe Quiz Answer the following questions by left clicking the mouse on the appropriate part of the Wood Lathe.

Rollover Protective Structures On Tractors Reasons for ROPS December, 2010.

Study of Popular Architectural Styles of Houses in America

DAY ONE - STEP ONE - Preparation Pure Crete is added to a water truck with a spray bar located at the rear of the truck at a ratio of one gallon to 2000.

The information in this show is for operating a Forklift Truck

Loading and Hauling.

© Easy Guides Australia a work platform consisting of a work basket (platform), lifting mechanism and chassis that can raise and lower people and materials.

Purpose Body Making module is designed for bending the laminated foil film in the shape of a tube, for welding the side seam and for cutting bodies with.

Introduction to Dental Lab Equipment

120M MOTOR Grader. 120M MOTOR Grader WIIFM Gain the ability to create and maintain roads Build flight lines Level areas.

© Easy Guides Australia A scraper means a piece of earthmoving equipment with the ability to scrape and move a quantity of soil and to discharge it at.

200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt.

Mobile Equipment Hazards

© Easy Guides Australia A boom-type elevating work platform means; a powered telescoping device, hinged device or articulated device or any combination.

Unwinding module is designed for unwinding of laminate tape, for its steering, for the cutting of the necessary width and for the easy feeding of material.

Physical Science Ch 5 (Part II) : Simple Machines.

Woodwork Planes. Plane Parts Smoothing Plane The Smoothing Plane is generally used for fine finishing and planning wide flat boards (like table tops)

Portable Power Planes, Routers, and Sanders

Chapter 11 Finishing Equipment

Material Handling. Introduction Handling and storing materials include a wide variety of tasks like: Hoisting tons of steel with a crane Driving a truck.

© Easy Guides Australia A Ride on Mower is a powered mower where the operator is seated at the controls. These often resemble small tractors, with the.

Woodworking with Power

Kitchen Basics Planning and trends. Kitchens are... Considered the control center most lived in room of the house most often remodeled strong selling.

 In ancient times, there were no machines to assist in transporting large stones for the building of pyramids  People had to get very large stones across.

Lecture 6 Loading and Hauling

Features favoring PM Small Size Geometry - Flat surfaces with few thicknesses - Straight side walls (constant cross-section) - surface finish and precision.

Basic Tool Safety and Equipment

Machining By: Corey LaBarge Machining Benefits n Opens many doors –Various engineering fields such as: n Industrial Engineering n Manufacturing Engineering.

© Easy Guides Australia The information in this show is for operating a Tractor. NEXT A tractor means: A vehicle that has a powerful petrol or diesel motor.

Proper Use of Agricultural Mechanics Power Tools

Chapter 9 Knife Skills. © Goodheart-Willcox Co., Inc. Objective Apply the procedures for preparing a workstation for knife work.

Surface Area and Volume of Cylinders. Surface Area  Cylinder – (circular prism) a prism with two parallel, equal circles on opposite sides.

1 Existing Product Analysis Controls The buttons are very big, easy for a child to press because of the large surface area Clearly spaced out from each.

ENGINE PURPOSE Converts chemical energy into mechanical energy to produce power to move the vehicle.

Rollover Protective Structures On Tractors Module One The Real Reasons For ROPS.

Week No. 02 Lesson Name File

WOOD MATERIALS TECHNOLOGY 4 th Edition. Chapter 22 Machines.

FRONT END LOADER SAFETY

Bell Ringer  Why do we use machines?  What is the formula for work?  What are the SI units for work?  What is the formula for power? 

Rectangular Prism Cylinder SPI I CAN determine the surface area of a 3-D figure.

Printing methods – what you need to know 1.Colour separation 2.Process colours 3.CMYK 4.Registration marks and the order of application of colours 5.Digital.

MATTING. REMEMBER… Matt Board is expensive. Measure twice, cut once. Lay your matt board on something clean… on newsprint for example, NOT the floor!

Woods and Processes Theory. Knowledge and Understanding.

Sanding is used to remove small amounts of material from surfaces, and to make them smoother.surfaces.

Planer Machines. Introduction A planer is a type of metalworking machine tool that is some what similar to a shaper, but larger, and with the entire workpiece.

Pictorial Oblique Drawing By B. Cowan & R. Cash. Cavalier Projection Cabinet Projection Receding Lines are half size or less.

PostBase Automatic Feeder Component Removal Service Training

Patterns used in Casting Process

Proper Use of Agricultural Mechanics Power Tools

Driver Education Section VI

Articulating Casts on the Hanau Articulator

Knife Skills 12. Knife Skills 12 Objective Prepare a workstation for knife work.

Chapter 4: Sheet Metal Forming

Exploration Lateral Learning

Preparing Prints for Salons

JEOPARDY Welcome to Jeopardy.

Grinding Edges Square & Parallel

Mechanical Incisal Guide Table

Lathe Quiz Answer the following questions by left clicking the mouse on the appropriate part of the Wood Lathe.

Lecture 5 Dozer TSP-308 MPK Ferdinand Fassa.

Dimensions and Tolerances

Dimensions and Tolerances

Presentation transcript:

© Easy Guides Australia “Graders perform a wide variety of operations from moderate dozing work to precision grading.” Side Casting Mixing Trimming Shaping Finishing The information in this show is for operating a grader

© Easy Guides Australia An example of a Grader Cab Lift cylinder Frame Roll over protective structure Engine Tandem drive housing Mold board Cutting edge Circle Circle drawbar Steering cylinder

© Easy Guides Australia Answer: Provision provided to prevent the bowl from descending. Question 1: What precautions must be taken when an inspection or work has to be performed under a raised blade or attachment? MUST KNOW COMPETENCY

© Easy Guides Australia Answer: There is greater risk of turning the machine over with side hill travel. Question 13: Why should side hill travel be avoided where possible?

© Easy Guides Australia Answer: To loosen or rip up hard surfaces. Question 31: For what purpose are the scarifiers on a grader used for? Front mounted scarifierRear mounted ripper/scarifier