0 HIGHLY CONFIDENTIAL ILFS New Technology and Product Presentation Presented By: Scott Goldstein-President

1 Fugitive Adhesive and Dry Peel Requirements: Hot Melt Clean release Water-base Tackless or retack (if desired) Recommendations: to Series All fugitives must be tested on specific stock. Water-base Repositionable to be diluted with water (Lowest release value at 11 grams) (Higher release value at 20 grams for offset stocks and envelope flap) Hot Melt. Great anti-stain. Clean release.

2 Dry Peel Water-base with UV Topcoat ( with L9091VT) Hot Melt with UV Topcoat ( with L9042M) Refer to for process schematic.

3 UV Silicone Release Coating/Repositionable and Permanent Hot Melt and Water-base Adhesives For Hand Applied Labels: Apply L9091L free radical UV silicone via pattern gluer with photopolymeric plate, and then apply repositionable, or ANY standard permanent pressure sensitive hot melt. Apply L9091L free radical UV silicone via pattern gluer with photopolymeric plate, and then apply semi-permanent water-base pressure sensitive. Note: 300 fpm/400 watt lamp For Premium Release/Auto Dispensed Labels: PC-605 cationic UV silicones applied via flexo with photopolymeric plate with permanent PSHM or repositionable PSHM Refer to for process schematic.

4 Water-base Release Coating/Repositionable or Permanent Hot Melt Machine Requirements: Apply L9100 M (2 component system) via flexo applicator with photopolymeric plate. L9100 M exhibits clean release with both permanent and repositionable hot melt pressure sensitives, and with semi-permanent water-base PSA ( ). Dry with standard convection air at ºF for 0.5 sec dwell.

5 Benefit Summary of ILFS’s Integrated Label Technology Far More Cost Effective Offers a 33% cost savings over purchasing pre-converted release liner/pressure sensitive face stock and tipping it on to the web. Offers a 41% cost savings over purchasing and tipping on coated release liner alone. Offers further savings due to your ability to pattern-apply release coating and adhesive only in the areas that it is required. Faster Production Eliminates the need for slow, tip-on label application of pressure sensitive labels to the web allowing you to increase web speeds up to 800+ fpm.

6 Reduced Inventory Carrying Costs Eliminates the need for large inventories of converted pressure sensitive roll stock and allows you to convert on a just-in-time production basis. Additional Printing Surface You can print or image directly under the release coating to convey additional messages to customers after they have removed the label. Elimination of Stacking Problems Because two panels unite to form one continuous surface, the 4 mil imbalance created by tipping on release liner and pressure sensitive stock is eliminated. The result is a smooth, integrated label product that stacks flat on skids. Benefit Summary of ILFS’s Integrated Label Technology

7 Current New Business Development Opportunities Textured and High Profile (MBOSS) UV Topcoat (L9074V) for Screen over AGS films. L9074V for Screen over Low to 0% wax/silicone containing heat set varnishes. L9082T for flexo for over varnish application and over AGS films. L9066H for chemical texturing. UV Glitter and Pearlized Topcoat (press side add ) UV and Water-base Glow-in-the-dark Coatings (For Screen and Flexo: UVS100V (green) and UVS102V (blue). Coat weights at mil. UV Thermochromic (UVS101V [flexo] and UVS109V [Screen]). 31ºC activation temp. Flexo applied at mil coat weight. Black to clear. UV Silver/Gold Scratch-off (L9093HS or HG). Run over 96U152H/L9091L (90:10% to 80:20%) primer. Use Gallium doped, V-Bulbs if enhanced cure is needed. Hot Melt Remoistenable ( ).

8 Magnetized UV Varnishes for Low-end Magnet Promotions (UVS107V Binder/A6256P Powder w/A6428P Primer). UV Laminating Adhesive (UVA 105 M for Standard Performance). UV Pressure Sensitive Adhesive (UVPS100E). For cold foil applications For “plastic card” laminations Magnetic UV Varnish for Information Strips on Credit Card (For E-beam only) UV MBoss replacement for traditional raised image foil stamping (L9213S). Current New Business Development Opportunities

9 In-Line Magnets Manufacturing Lay down high-profile magnetic UV at mil via rotary screen coater (80/40 mesh). Cure UV with Gallium doped V-bulb. Magnetize UV with Multi-pole magnet roller. Charged piece can either be sheeted or finished in-line like kiss die cut labels.

10 Allows magnets to be produced on paper (vs. vinyl). Allows for personalization. Allows for pattern application, reducing cost and waste. Allows for pattern coating with a 1/16 inch border, SIGNIFICANTLY increasing life of dies Postal savings due to 67% lower weight of piece. In-Line Magnets