Accomplished Recommendation Planned Actions for Control

Slides:

Advertisements

Similar presentations

and Statistics, 2016, Vol. 4, No. 1, 1-8. doi: /ajams-4-1-1

Advertisements

© The Author(s) Published by Science and Education Publishing.

Table 4. Age group distribution of enteropathogens

Percentage of Polyethylene

Properties Test results

© The Author(s) Published by Science and Education Publishing.

Supplier Input Process Output Customer

© The Author(s) Published by Science and Education Publishing.

Table 2. Result of Actual Technical Writing Needs

Hospital live Deliveries

Research, 2015, Vol. 3, No. 6, doi: /education

Table 5. Properties of The Tested Soil

© The Author(s) Published by Science and Education Publishing.

SON Nurse Practitioner Blackboard Community

Total Energy Consumed (%)

Tensile Test after Firing

intervals from six months to one year

Marshall characteristics

© The Author(s) Published by Science and Education Publishing.

Table 8. Drawing result before game

Table 4. women involvement in environmental management

Table 2. Levels of youth Involvement in Community Development Programs

© The Author(s) Published by Science and Education Publishing.

Table 4. Percentage of post-harvest waste reported by the farmers

© The Author(s) Published by Science and Education Publishing.

Table 6. Control sample industry distribution

Total CO2 Emissions (Electricity + Fossil Fuel)

© The Author(s) Published by Science and Education Publishing.

© The Author(s) Published by Science and Education Publishing.

Table 2. Waste characterization in Port Harcourt, Source [1]

Table 3. The needed requirements of the Concrete Sustainability

FSV Interpretation (qualitative)

© The Author(s) Published by Science and Education Publishing.

© The Author(s) Published by Science and Education Publishing.

Number of categories that are mentioned (0% < categories < 5%)

Table 1. Diagnostic methods for systemic fungal infection (n=70)

Table 1. Geometric properties of steel tubes used

Table 2. Modal parameters estimated by Pulse Reflex®

Table 1. The most important aspect applied in MIVES

Table 7. Status of CF in Nepal as of 2009

Table 5. Pvalues of ttests for direction a

Table 1. Summary Statistics of Top Cut 1-m Samples

Entrapment Efficiency (%) ± S.D.

Interpass temperature

Table 3. Main properties of the thin brass electrode

© The Author(s) Published by Science and Education Publishing.

© The Author(s) Published by Science and Education Publishing.

Table 1. Characterization Result of Leaded Petrol and Blends

Simulation Frequency(Hz)

Injection Substations No. of Transformer Units Installed

Table 6. Pvalues of ttests for direction b

Table 2. Regression statistics for direction a

Table 3. Regression statistics for direction b

Average Hardness value (HRC)

Table 3. List of PT specimens

Table 6. Percentages of Indicators

Table 4. Surface roughness (outer faces)

© The Author(s) Published by Science and Education Publishing.

Control Valve Tag Number

Figure 2. MDS-T configuration for the thirteen (13) criteria (and their Place) in DPESS in Athens (NKUA) Chris P. Lamprou et al. Evaluating the effectiveness.

No. of runs Xo X1 X2 X3 X4 Y1 Y2 Y3 Y4 Y5 Si2

Table 1. Illiteracy distribution by Gender and Place (No. in million)

© The Author(s) Published by Science and Education Publishing.

© The Author(s) Published by Science and Education Publishing.

© The Author(s) Published by Science and Education Publishing.

Table 3. Surface roughness (inner faces)

Compressive Strength difference at 1 week (MPa)

Table 6. Twisting moment of counter shaft at different torques

© The Author(s) Published by Science and Education Publishing.

Average Execution Time in seconds

Presentation transcript:

Accomplished Recommendation Planned Actions for Control Table 5. Control Plan Communicated for the Company Staff Accomplished Recommendation Planned Actions for Control Frequency Responsibility A contract with a new supplier for steel wire was established -Evaluation for all suppliers -Three months -Purchasing Department Mixing machine replaced by a new one with a more reliable counter. -Predictive and Preventive maintenance as per manuals -Weekly -Maintenance Department Complete maintenance was implemented to the drawing and cutting machine Cleaning process of the work space -Set schedule forcleaning with a checklist and signature -Daily -Production Department Instructions for engineers to avoid having any unpacked products -Ensure that there is no unpacked products Mohamed K. Hassan et al. Applying Lean Six Sigma for Waste Reduction in a Manufacturing Environment. American Journal of Industrial Engineering, 2013, Vol. 1, No. 2, 28-35. doi:10.12691/ajie-1-2-4 © The Author(s) 2013. Published by Science and Education Publishing.