PPPoA Test Configuration Example on IDL-4800 to ADE-4400 / 3rd party device

PPPoA Test Configuration Uplink BP: VLAN-2, tagged IF xDSL-1, PVC-1: PVID-2, Untagged PPP server ASUS AM_604g PPPoA connection enabled DHCP Server enabled Untagged IF PVID-2 VLAN-2 tagged IF PC#1 ADE-4400 PPPoA connection enabled DHCP Server enabled IP: Dynamic IP

PPPoA Test Configuration Modem PPPoE/PPPoA Server IP DSLAM L2 Switch PPPoE / PPPoA server Ubuntu + PPPoE server IP DSLAM IDL-4800 Modem ADSL CPE Modem

Steps for the PPPoA test Make sure your PPP service on the Server is running. Configures DSLAM to have a proper setting. Configures the ADSL Modem (ex: ADE-4400 & ASUS AM_604g) Configures your switch and make sure all VLAN setting is correct. Verify traffic path of PPPoA connection.

DSLAM configuration

IDL-4800 DSLAM running config management mgmt 172.16.9.44 netmask 255.255.255.0 management gbe 192.168.100.1 netmask 255.255.255.0 route default 172.16.9.254 snmp 1 community rw "public" igmp version v2 igmp snooping interface gigabit 1 bridge default vlan 1 egress untag vlan 2 priority reserved tag isolation interface gigabit 2 interface xdsl 1 adsl-config line status service on bridge 1 pvc 0/35 pvc encapsulation auto default vlan 2 interface xdsl 2 cluster-cfg name "u71577C" bye < running config >

IDL-4800 DSLAM running config Note: For the PPPoA application , please configure ADSL PVC encapsulation mode as “Auto”

Example device: PLANET ADE-4400 configuration

Configuration on PLANET ADE-4400 Click Network  WAN Key in the parameters VPI: 0 VCI:35 according to DSLAM’s setting Select VC-Mux (or LLC) for encapsulation Select PPPoA Enable NAPT Key in User Name / Password And then ADD to add the channel Save the Configuration

Example device: ASUS AM_604g configuration

Configuration on ASUS AM_604g Click Advanced Setup  WAN Click Add Button

Configuration on ASUS AM_604g (Cont.) Input your VPI and VCI number

Configuration on ASUS AM_604g (Cont.) Select connection type and encapsulation mode VCMUX or LLC for PPPoA

Configuration on ASUS AM_604g (Cont.) Input your PPP Username and Password for PPPoA connection Click Next Button

Configuration on ASUS AM_604g (Cont.)

Configuration on ASUS AM_604g (Cont.) Click Save Button

Configuration on ASUS AM_604g (Cont.) Click Finish button

Configuration on ASUS AM_604g (Cont.) Click Advance Setup  Routing  Default Gateway Select Enable Automatic Assigned Default Gateway check box Click Save/Apply button

Configuration on ASUS AM_604g (Cont.) Click Advance Setup  LAN Select Enable DHCP Server check box Click Save/Reboot button Save/ Reboot

PPPoA Status on ASUS AM_604g If PPPoA works and all the settings of PPP server, DSLAM, and CPE are correct, the WAN Info of CPE will show status is ‘Up’ and PPP server will assign an IP to this CPE.

Verify traffic path of PPPoA connection

PPPoA Verification PPP server PC#1 PC#2 Uplink BP: VLAN-2, tagged IF xDSL-1, PVC-1: PVID-2, Untagged PPP server Untagged IF PVID-2 ASUS AM_604g PPPoA connection enabled DHCP Server enabled VLAN-2 tagged IF PC#1 PC#2 ADE-4400 PPPoA connection enabled DHCP Server enabled IP: Dynamic IP After PPP session is established, PC#1 can access the same LAN (PC#2) as PPP server and internet (WAN, depends on PPP server setting.) for testing.