BASEPLATES SLIDE SHOW.

Slides:

Advertisements

Similar presentations

Unit 8 Fastening Systems

Advertisements

Unit 5 Steel Frame Construction

Actions and Retrofit of Post Earthquake-Damaged Bridges

General Information Dimensions · Structure Width: ~ 197in. (16.4’), 99in. (8.2’)/car · Slope Angle: 5 degree · Structure Height (Front): 100in. + base.

Glenn Murcutt Anna James Construction & Structures 2 SRT251.

Pipe Supports and Hangers

INTRODUCTION TO THE NEW SUBPART R Prepared by the U.S. Department of Labor, OSHA Office of Construction Standards and Compliance Assistance.

Advanced Construction Technology

Installation Instructions. Delivery Light fixtures, mounting structures and electrical components ship together Poles ship on a separate truck.

Concrete Pre Cast Panel By Peter Spence ID:

Threads and Fasteners.

Foundation Systems.

Chapter 7 Metals.

Shear - Tensile - Compression Stresses Slip Ted 126 Spring 2007.

Rectangular framed structures

Solid Projections (Solid State Welds)

STEEL FRAMED STRUCTURES Steel is a material which has excellent structural properties. It has high strength in tension and compression. It is the strongest.

Floor Systems and Foundation Support

Chapter 18 Foundations.

B ASEPLATES S LIDE S HOW. Anchor Bolts are positioned and placed in the concrete before it cures. Plastic caps are placed over the anchor bolts to protect.

Chapter 10 Web splice.

Appendices Subpart R Steel Erection

1926 Subpart R OSHA’s Steel Erection Standard Scope

J-FRM-0101 Revision with Reason No.DateInitials Drawing No. D’Vinyl Inc. Descriptive Part Name Designed byChecked by Engineer Drawing Type Foot Plate Date.

Update of anchoring procedures for the ALS floor 09/19/2007.

Earls Mill Road Retaining Wall Ground Anchors and Strengthening.

Chapter 32 Floor Systems and Foundation Support. 2 Links for Chapter 32 Slab Construction Reinforcing Concrete Crawl Spaces.

Argonne National Laboratory is managed by The University of Chicago for the U.S. Department of Energy LCLS Girder Support Concept Design Sushil Sharma.

ELENA Support system 6/11/2014 Antti Kolehmainen on behalf of WP Support system

Moment Connection Requires Bolts Outside the Flanges

TF Coil Vacuum Vessel Wire Rope Tensioning Fixture 3 Per Segment Horizontal Stop 3 Per Segment Wood Block 2 Per Segment TFTR D&D FMEA REVIEW Vacuum Vessel.

ID 1.75 Material list: aluminum ¼ X ¾ X 6 in flat bar ¾ X 6 in round stock 1 X 6 in round stock 2 ea 5/16 heli-coil Weld 1” joints.

Step IV Construction North Side Walls and End Walls May 2015 Stephen Plate, Brookhaven National Laboratory.

Chapter 43 Common Commercial Construction Materials.

Fundamentals of Structural Detailing

6.03 Tools in Agricultural Engineering Obj. 6.03: Remember tools and their safety practices related to the agricultural mechanics industry Images courtesy.

Objective 6.03 Remember tools and their safety practices related to the agricultural mechanics industry.

IN MODULAR CONSTRUCTIONS

WisDOT - Bureau of Structures Brandan Burger.  Anything “structural” – change in loading, structural capacity, pile locations  If in doubt, call us!

Side view of generator. Close up of unused grounding pad - gives provisions for mounting the absorber.

Foundation Loads Dead Load Live Load Wind Load

Riser And Lid Assemblies. Description Risers and Lid assemblies are components designed to provide access and security at grade level to system components,

Design of Bracing Connections in Concentrically Braced Frames

Steel Fabrication & Erection of Belle Chasse Primary School ET-493 Final Proposal Spring 2015 Instructor: Chris Koutsougeras Advisor: Edward Rode’ Derek.

Footings & Foundation Prepared By: (Vanani Sanket) Department of Civil Engineering B.H.Gardi College of Engineering & Technology.

Leads Institute of Technology & Engineering

Warm Vessel Leveling Islands (Piers)

Foundation – jay Desai.

Girder-Magnets Installation

Sardar Patel Institute Of Technology

Remember tools and their safety practices related to the agricultural mechanics industry. Objective 6.03.

Escalator Installation

MICE Partial Return Yoke Mechanical Design

Gang Form Fall During Installation

Steel Erection 29 CFR 1926, Subpart R

CONNECTIONS IN STEEL STRUCTURES

MACHINE PARTS (FOR DCE / DIT)

Square Tube Shaft Connecting Both Gear Drives.

1C2 Conceptual Design of Buildings

Always ensure the correct grade and length bolts are used

CONNECTIONS IN STEEL STRUCTURES IS CRITERIA

Experience the StructureCast Advantage!.

Chapter 7 Foundation Systems.

INTRODUCTION TO THE NEW SUBPART R

Valve stem “gag” mechanism

Senad Kudumovic Design engineer

Neutron guide Shielding Concept

Steel Erection 29 CFR 1926, Subpart R

Fixed Support Design & Testing

Presentation transcript:

BASEPLATES SLIDE SHOW

Anchor Bolts are positioned and placed in the concrete before it cures Anchor Bolts are positioned and placed in the concrete before it cures. Plastic caps are placed over the anchor bolts to protect laborers.

Interior Column Perimeter Column Concrete block-outs are made so that the base plate and anchor bolts are recessed below floor level for safety and aesthetics.

Base plate holes are located and drilled in the shop Base plate holes are located and drilled in the shop. The base plates were shop-welded to their respective columns and shipped to the site. Slotted holes are allow for difference in standard field tolerances between concrete and steel.

Base plate and column installation is complete Base plate and column installation is complete. The column is leveled by adjusting the anchor bolt nuts below the plate. Grout will be placed under and around the base plate to smoothly transfer axial forces to the concrete below. Interior and perimeter column installations are complete. After inspection, the block outs will be filled with concrete to floor height for a uniform appearance and safety.

Yes! They do miss, and field corrections are made!