ECET 340 Teaching Effectively-- snaptutorial.com

ECET 340 Entire Course (All ilabs and Homework) For more classes visit ECET 340 Week 1 HomeWork 1 ECET 340 Week 1 iLab 1 ECET 340 Week 2 HomeWork 2 ECET 340 Week 2 iLab 2 ECET 340 Week 3 HomeWork 3 ECET 340 Week 3 iLab 3 ECET 340 Week 4 HomeWork 4

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 1 HomeWork 1 For more classes visit Give three examples each of internal and external peripheral devices as referenced to the HCS12 microcontroller and not an entire PC. (2 points) 2. Given “the requirements of each signal’s destination must match the capabilities of the signal’s source,” name some of the electrical signal parameters that must be considered when designing an interface between two different hardware components. (2 points)

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 1 iLab 1 For more classes visit OBJECTIVES: To become familiar with Microcontroller MC9S12 parallel ports and how simple input and output devices are interfaced through them. To learn how to program I/O instructions in C language.

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 2 HomeWork 2 For more classes visit 1. Where does program control transfer to when an interrupt occurs? +2 points 2. Which one of the following Interrupts has highest priority? +2 points 3. RAM Vector table addresses $3E52 belongs to which interrupt? +2 points 4. Before exiting an ISR, the programmer should use which command? +2 points 5. In which one of the following sequences is the stack pulled by rti? +3 points 6. Given the starting address for the TC0 Interrupt is to become $5000. Write the assembly instruction necessary to pla

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 2 iLab 2 For more classes visit ECET 340 Week 2 iLab 2

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 3 HomeWork 3 For more classes visit 1. Sketch a circuit that can be used to debounce a pushbutton and explain how it works. (4 points max) 2. In Figure 7.32 on page 339 of the Huang textbook, if the row has and the columnsare, which key is pressed? (2 points max) 3. In Figure 7.32 on page 339 of the Huang textbook, explain why the 10kΩ resistors ties to VCC are required. (2 points max)

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 3 iLab 3a For more classes visit SOLVED ECET 340 iLAB3 OBJECTIVES: To learn the basic operation of a keypad. To understand how to interface a keypad to a microprocessor. To learn how to program a keypad driver in C language.

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 4 HomeWork 4 For more classes visit Determine the conversion time for an ADC0804 (8-bit), where 66 clocks per bit are required, if its clock frequency is 50 kHz. 2. If an 8-bit SAR has Vref = 10 V, what is the binary value for an input voltage of 7.28 V?

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 4 iLab 4 For more classes visit OBJECTIVES: To learn how to use A-to-D converters to digitize signals from analog input devices. To learn how to write a C language program that samples the data from an analog device, digitizes it and formats it for output on an LCD. To become more proficient in programming displays for real-time operation.

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 5 HomeWork 5 For more classes visit Explain, briefly, why an analog restoring filter is sometimes used at the output of a DAC. 2. Given Iref = 2 mA for a DAC1408 IC, find Iout for the input Find the number of discrete voltages output by a 12-bit DAC. Show work.

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 5 iLab 5 For more classes visit Scenario/Summary This week's lab covers two areas, conversion of digital HCS12 signals to an analog format, and the use of a Serial Peripheral Interface (SPI) to transfer data, and commands between the HCS12, and the DAC peripheral. Deliverables For this lab, the deliverables include the cover sheet,

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 6 HomeWork 6 For more classes visit What are the four main functions of the HC12 Timer unit? 2. Two input capture events occur at counts 0x1037 and 0xFF20 of the free-running counter. How many counts (in decimal) have transpired between these two events? 3. What is the maximum time possible before the free-running counter overflows when the e MHz?

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 6 iLab 6 For more classes visit ECET 340 Week 6 iLab 6

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 7 HomeWork 7 For more classes visit 1. The movable part of the solenoid is the: +2 points 2. Why is the 6N139 optoisolator used in the interfaces to devices such as large motors? +2 points 3. Calculate the number of steps per revolution for a stepper motor with a step angle of 7.5°. +2 points 4. How is stepper motor speed controlled? State any two ways a program can do this. +2 points

ECET 340 Teaching Effectively-- snaptutorial.com ECET 340 Week 7 iLab 7 For more classes visit ECET 340 Week 7 iLab 7

ECET 340 Teaching Effectively-- snaptutorial.com