ENGINEERING GRAPHICS.

Slides:



Advertisements
Similar presentations
ENGINEERING GRAPHICS 1E7
Advertisements

Drafting – Product Design & Architecture
THE ELLIPSE. The Ellipse Figure 1 is ellipse. Distance AB and CD are major and minor axes respectively. Half of the major axis struck as a radius from.
1 ANNOUNCEMENTS  Lab. 6 will be conducted in the Computer Aided Graphics Instruction Lab (CAGIL) Block 3.  You will be guided through the practical.
Dr. Mohamed BEN ALI.  By the end of this lecture, students will be able to: Understand the types of Tangents. Construct tangents. Construct incircle.
Geometric Construction Notes 2
Geometric Constructions: Congruent Segments and Congruent Angles Geometry Mr. Zampetti Unit 2, Day 1.
Circles.
Copyright  2012 McGraw-Hill Australia Pty Ltd PPTs t/a Engineering Drawing 8e by Boundy 5-1 Chapter Five Geometrical Constructions.
Essential Question: How do I construct inscribed circles, circumscribed circles, and tangent lines? Standard: MCC9-12.G.C.3 & 4.
3rd Angle Orthographic Projection
Similarity, Congruence & Proof
Implementing the 7 th Grade GPS: Constructions, Transformations, and Three-Dimensional Figures Presented by Judy O’Neal North Georgia.
Perpendicular Bisector of a Segment and Angle Bisector
J.Byrne Geometry involves the study of angles, points, lines, surfaces & solids An angle is formed by the intersection of two straight lines. This.
Creating Constructions Unit 7. Word Splash Constructions Construction – creating shapes using a straight edge and a compass Straight edge – clear,
(Point undergoing two types of displacements)
Geometric Constructions
Geometric Constructions October - Ch. 3 Part of Unit 2 – Lines & Angles.
Constructing Perpendicular Bisectors and Lines Right angles Cut in Half.
Mechanical Drawing Lesson 5 Geometric Construction Created By Kristi Mixon.
Constructions Bisect – To divide something into two equal parts Perpendicular – Lines that intersect to form right angles. Today’s constructions: –Bisect.
CONIC SECTIONS ELLIPSE, PARABOLA AND HYPERBOLA ARE CALLED CONIC SECTIONS BECAUSE THESE CURVES APPEAR ON THE SURFACE OF A CONE WHEN IT IS CUT BY SOME TYPICAL.
GEOMETRIC CONSTRUCTION
Similarity, Congruence & Proof
Day 43 – regular hexagon inscribed in a circle
Engineering Graphics Lecture Notes
CYCLOIDS.
Geometrical Constructions
Day 44 – Summary of inscribed figures
Geometry 1 J.Byrne 2017.
Part- I {Conic Sections}
Basic Geometric Terms & Construction
GEOMETRIC CONSTRUCTIONS
Geometric Constructions
Don’t change your radius!
Constructing Perpendicular Bisectors and Lines
Day 41 – Equilateral triangle inscribed in a circle
Compass/Straight Edge
TECHNICAL CURVES.
Auxiliary Views & Development
Engineering Curves.
ELLIPSE.
ENGN103 Engineering Drawing geometric constructions
Chapter 2 Applied geometry.
Dr.R. GANESAMOORTHY.B.E.,M.E.,Ph.d. Professor –Mechanical Engineering Saveetha Engineering College TandalamChennai. 9/12/20181Dr.RGM/Prof -Mech/UNIT 1.
ENGINEERING GRAPHICS 1E9
ENGN103 Engineering Drawing geometric constructions
We are Learning to…… Name Parts of a Circle.
GEOMETRIC CONSTRUCTION
MATHEMATICS WORKSHEET
Geometric Constructions
ENGN103 Engineering Drawing
ENGINEERING CURVES By: Muhammad Zahid.
Compass/Straight Edge
CHAPTER 2: Geometric Constructions
Chapter 2 Using Drawing Tools & Applied Geometry.
principle of geometric construction Prepared by: Asst. lecture
Part- I {Conic Sections}
Principle of Geometric Construction (I) Prepared by: Asst. lecture
Y. Davis Geometry Notes Chapter 10.
ENGN103 Engineering Drawing geometric constructions
Applied geometry Flóra Hajdu B406
Day 44 – Summary of inscribed figures
Chapter 2 Using Drawing Tools & Applied Geometry.
Math 9 – Unit 8 Circle Geometry.
Anjuman College of Engineering & Technology
Using a protractor, draw the angles:
Presentation transcript:

ENGINEERING GRAPHICS

Drawing Parallel Lines DRAWING LINES Drawing Parallel Lines

Drawing Perpendicular Lines DRAWING LINES Drawing Perpendicular Lines

DRAWING LINES Bisection of A Line Place your compass point on A and stretch the compass MORE THAN half way to point B. With this length, swing a large arc that will go BOTH above and below segment AB.  Without changing the span on the compass, place the compass point on B and swing the arc again.  The new arc should intersect the previous one above and below the segment AB. With your scale/ruler, connect the two points of intersection with a straight line. This new straight line bisects segment AB.  Label the point where the new line and AB cross as C. Segment AB has now been bisected and AC = CB.  A B

Divide A Line into Multiple Sections DRAWING LINES Divide A Line into Multiple Sections From one end of the given line AB (say, A) draw a line AC at a convenient angle Using a scale/ruler divide the BC into the required number of parts making them of any suitable length. Join the last point on line AC (say, C) to B Draw construction lines through the other points on the line AB which are parallel to CB

DRAWING LINES Bisection of An Angle Place the point of the compass on the vertex of angle BAC (point A). Stretch the compass to any length so long as it stays ON the angle. Swing an arc with the pencil that crosses both sides of angle ABC.  This will create two intersection points (E and F) with the sides of the angle. Place the compass point on E, stretch your compass to a sufficient length and draw another arc inside the angle - you do not need to cross the sides of the angle. Without changing the width of the compass, place the point of the compass on F and make a similar arc.  These two small arcs in the interior of the angle should be crossing each other. Connect the point of intersection of the two small arcs to the vertex A of the angle with a straight line.  

Find the Centre of an Arc DRAWING LINES Find the Centre of an Arc Select three points A, B and C on the arc and join AB and BC Bisect AB and BC. Fine the intersection point of the bisecting lines/bisectors. That is the centre of the arc.

Inscribe a Circle in a Triangle DRAWING LINES Inscribe a Circle in a Triangle Bisect angle ABC and angle BAC. Fine the intersection point of the bisecting lines/bisectors. That is the centre of the circle. The radius of the circle is the length of a perpendicular line on any of the sides of the triangle drawn from the centre of the circle.

Circumscribe a Circle on a Triangle DRAWING LINES Circumscribe a Circle on a Triangle Bisect sides AC and BC. Fine the intersection point of the bisecting lines/bisectors. That is the centre of the circle. The radius of the circle is the length of a line joining any one of the vertices of the triangle to the centre of the circle.

DRAWING LINES Draw a Hexagon To draw a regular hexagon given the distance across flats Draw a circle having a diameter equal to the distance across flats. Draw tangents to this circle with a 60° set square to produce the hexagon.

DRAWING LINES Draw a Hexagon To draw a regular hexagon given the distance across corners, draw a circle having a diameter equal to the distance across corners Step off the radius round it to give six equally spaced points. Join these points to form the hexagon.

Ellipse Construction Draw the axes AB and CD and draw circles (called auxiliary circles) on them as diameters. Divide the circles into a number of equal parts, by radial lines through O. Each of the radial lines intersect the major and minor auxiliary circle. Through the points where radial lines cut the major auxiliary circles drop vertical perpendiculars, and through the points where the radial lines cut the minor auxiliary circle draw horizontals to cut the verticals. These intersections are points on the ellipse.

CYCLOID The cycloid is the locus of a point on the rim of a circle rolling along a straight line.

HYPOCYCLOID The curve produced by fixed point P on the circumference of a small circle of radius a rolling around the inside of a large circle of radius b.

EPICYCLOID The path traced out by a point P on the edge of a circle of radius a rolling on the outside of a circle of radius b.

Involute of a line (AB): C

What is an involute ?? Attach a string to a point on a curve. Make the string a tangent to the curve at the point of attachment. Then wind the string up, keeping it always taut. The locus of points traced out by the end of the string is called the involute of the original curve. The original curve is called the evolute of its involute.

Example: Circle

Example: Triangle

Archimedean Spiral Spiral of Archimedes is a spiral with polar equation

Try this!