WORKSHOP PRACTICE WEEK-5 OBJECTIVE OF LAB-5 Introduction to digital multimeter and its measuring method. To be familiar with the connections of.

Slides:

Advertisements

Similar presentations

As a stand-alone overview of test tools.

Advertisements

12.1 Electricity at Home (Pages )

March 2004 Labpacks Physics Equipment. March 2004 Labpacks We have two types of power supplies in the lab. They are called ‘Labpacks’ They allow you access.

Using a Multimeter.

Institute Of Applied Technology ATE 1010 Grade 10 Ms. Rose Hasan.

Chapter : 7 : Mains Electricity

EET Electronics Survey Chapter 8 - Measuring Voltage, Current, and Resistance.

Meter Lab Introduction to Electricity Assignment for tomorrow: Read chapter R1.

PRACTICAL ELECTRONICS MASTERCLASS (Mr Bell) 1. Fault finding A fault is when a piece of equipment does not work the way it had been intended too. Fault.

Circuit Testers and Digital Meters 22 Introduction to Automotive Service James Halderman Darrell Deeter © 2013 Pearson Higher Education, Inc. Pearson Prentice.

Circuit Testers and Digital Meters

Chapter 7. Voltage Remember: Atoms are in EVERYTHING and they are made up of equal amounts of positive and negative charges. Battery: uses chemical energy.

Unit 14: Electricity Part One: Electric Circuits.

Electrical Engineering. A circuit is a combination of different components that allow electricity to flow through them. Each component serves its own.

EGD ELECTRICAL ELECTRICAL SYMBOLS.

Wiring Accessories Energy & Environment.

Electrical Fundamentals

Introduction to Digital Multimeters

Electricity and Electrical Circuits. Chapter Sections O 1 - Electrical Circuits O 2 - Current and Voltage O 3 - Resistance and Ohm’s Law.

SAFETY FEATURES USED IN THE CIRCUITS OF THE MAINS SUPPLY

JEOPARDY GreenAnythingGoes MeasurePowerConnectionsElectricity Micro Comp. Final.

Class exercise 1 Find the equivalent resistance of the following circuit.

Circuits and Electronics. Circuits A circuit is a closed path through which a continuous charge can flow. A circuit is a closed path through which a continuous.

Phase Presence and Sequence Tester (FAST-1) Boris Fradkin 2015 A.L.F. Enterprise.

Electric Circuits17.4. Electrical Safety Tips Make sure insulation on cords is not worn Do not overload circuits Do not use electrical devices while hands.

13.2: Current and Voltage Objectives: Ampere Voltage Volt Voltmeter

Electric Circuits Part Two: Current and Voltage Learning Goals  Explain how current flows in an electric circuit.  Define voltage and describe how.

Chapter 7 Electricity. What is Charge? Protons have a (+) charge Electrons have a (-) charge Charge (q) is measured in Coulombs The elementary charge.

Lesson 6 Voltage Do we need to MEASURE it? OR Do we need to DETECT it?

DIGITAL MULTIMETER A Must Have For Dealing With Electronics.

Electrical Engineering CHAPTER 14. Electrical Engineering (404)  Electricity is all around us. It runs our homes, offices and schools.  Designing and.

UNIT FIVE: Electricity and Magnetism

Lab instruments ELCT 201 Digital Multimeter Voltage Tester

Electricity and Safety Grade 6 Science. What do we need to learn? Outcome identify and explain the dangers of electricity at work or play. Outcome.

PR570 POWERITE II TRAINING Dedicated to Success in Electronic Servicing for 50 Years.

ELECTRICAL SAFETY FOR INSTRUMENTS SECTION. Electrical measurement safety Understanding hidden hazards and new safety standards.

Basic Equipment and Schematic Reading. Objectives Learn the basic equipment that will be used in the Lab. Learn some of the basic symbols used on electrical.

SAMI MAKERSPACE MAKE: AN ELECTRONICS WORKSHOP. ELECTRICITY BASICS.

16.2 Current and Voltage. Electric Current (review from yesterday) Electric current: the flow of electric charge (movement of electrons)

P2 - Physics Mains Electricity

Lab 2. Do now Answers Improperly grounded outlets can cause errors in a computer system that may not be immediately apparent from internal diagnostics.

Electric Circuits Chapter 14, Section 4. Circuits consist of an energy source, a load, wires, and in some cases, a switch.

Objectives 1. Demonstrate the requirements for an electrical circuit that works. 2. Use a multimeter effectively to measure voltage and current in a simple.

Current: A flow of electrons, or individual negative charges. Current: A flow of electrons, or individual negative charges. Copyright © 2010 Ryan P. Murphy.

Using a Multimeter.

UNIT-5. ELECTRICAL SAFETY, WIRING & INTRODUCTION TO POWER SYSTEM

Notes: Electric Circuits

Chapter Twenty: Electric Circuits

ELECTRIC CIRCUITS.

Circuit Protection Unit 9.

ELECTRIC CIRCUITS 20.3.

UNIT FIVE: Electricity and Magnetism

Introducing Current Electricity

ELECTRICAL CURRENT.

Electrical Safety in the Home

We have been working on Investigating Circuits. Let’s Review…

Voltage, Current and Resistance

Voltage, Current and Resistance

More electricity stuff

Electrical Quantities

Chapter Twenty: Electric Circuits

Experiment No. 1 Ohm’s Law

What is Electricity? Electricity is the flow of electrical charge because electrons start to move. All matter is made of atoms that contain electrons The.

RIDDLE If you screw a light bulb into a lamp socket by turning the bulb towards the right with your right hand, which way would you turn the socket with.

P2 - Physics Mains Electricity.

FIGURE 15–21 When connecting a starter tester such as a Sun VAT 45 to the vehicle, make certain that the inductive probe is placed over all of the cables.

Presentation transcript:

WORKSHOP PRACTICE WEEK-5

OBJECTIVE OF LAB-5 Introduction to digital multimeter and its measuring method. To be familiar with the connections of a door bell.

MULTIMETER WHY MULTIMETER? The most common electrical test equipment is a meter which is known as Multimeter. WHY MULTIMETER? Because it has the ability to measure different quantities such as voltage, current, resistance, and often many others.

MEASURING THE DC VOLTAGE OF A BATTERY

MEASURING THE AC VOLTAGE

CURRENT MEASUREMENT

CURRENT MEASUREMENT

CURRENT MEASUREMENT

SHORT CIRCUIT

When switching a multimeter from voltage- to current measuring mode SHORT CIRCUIT When switching a multimeter from voltage- to current measuring mode

HOW TO TEST A FUSE ? A good fuse will indicate very little resistance

BLOWN FUSE

HAND-TO-HAND SHOCK Hand-to-hand shock current path is the most dangerous, holding the meter probes on two points in a high-voltage circuit in this manner is always a potential hazard. If the protective insulation on the probes is cracked then what will happen?

SAFETY CONSIDERATIONS FOR LIVE MEASUREMENT Use only one hand. Special probe tip accessories such as spring clips, crocodile clips can be attached. Crocodile Clips Spring Clips

DOOR BELL The first doorbell was mechanical, activated by pulling a cord. The transformer is used to step the voltage down from 220V to 16, 18 or 24 volts. Modern doorbells are electric. They are actuated by an electric switch.

Electronic Door Bell

Electromechanical Doorbell

AC Doorbell

AC Power plugs and Scokets AC power plugs and sockets are devices that allow electrically operated equipment to be connected to the primary alternating current (AC) power supply in a building. Electrical plugs and sockets differ in voltage and current rating, shape, size and type of connectors. The types used in each country are set by national standards, some of which are listed in the IEC technical report TR 60083, Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC.

AC Socket

AC Plug

Types of Sockets

Pakistan C, D, G, M 230V 50 Hz

AC Tester Tester is used to test for live wire.

Practical Procedure Current of Door Bell ?

THE END