What do we need to know for our exam????

Slides:



Advertisements
Similar presentations
Letterpress to Laser. A modern flat-bed printing pressflat-bed printing press PRINTING.
Advertisements

BASIC COURSE IN PRINTING TECHNOLOGY
PRINTMAKING Going dotty for reproduction. Letterpress Printing press invented by Gutenberg in Relief printing – used wooden then metal block of.
Four Types of Printmaking
Printing processes.
Gravure Printing Cale Polkinghorne.
Commercial Printing Processes TPC November 2001 Barbara Manning.
GCSE Graphic Products Printing and Print finishes
Fundamentals of Printing
Printing Process AS Graphics. Offset Lithography.
GRAPHICS REVISION Thursday 22 nd April. SURFACE FINIHSHES.
INFORMATION. As promised last year we will look at some aspects of…. D&T: GRAPHIC PRODUCTS FINISHING FINISHING.
Printmaking. What is Printmaking? Artists choose a surface to be a “plate’. It could be linoleum, styrofoam, metal, cardboard, or stone. Then the artists.
MD. Mofakharul Islam Instructor (tech) & Head of the department Printing.
INFORMATION D&T: GRAPHIC PRODUCTS. We will look at some aspects of…. Typography Printing and D&T: CYNHYRCHION GRAFFIG.
Lithographic Printing
Overview of Graphic Communications
5 Major Printing Processes
Graphic Communication
The Graphical look at typefaces All typefaces are measured in the POINT SYSTEM, usually called pt. One point is equal in line spacing to 0.351mm. The.
PRINTING.
WEB PRINTING Maryam Chananeh CHA Web offset is a form of offset printing in which a continuous roll of paper is fed through the printing press.
Graphic Communications
Academic + Finishing Skills Week 2 History of Print Production - An Introduction BBCD Melbourne BAPDCOM.
Printmaking!!!!!.
Printing 2 Assignment 1 MORGAN. Engraving  To make a print, the engraved plate is inked all over, then the ink is wiped off the surface, leaving only.
Print production process
Offset Lithography Flexography Gravure Printing. The Printing Processes.
Colour In graphic design we refer to most colour as ‘process colour’. What is process colour? It is colour made up of ‘C, M, Y, K’ or Cyan, Magenta, Yellow.
Printing Processes Unit 6 In Orange Book.
Stone Lithography: drawing with a litho crayon
Graphic DesignColour TheoryPrinting Methods $250 $500 $1000 Final Graphicardy.
SURFACE FINIHSHES. LAMINATING This also produces a high gloss finish on card and provides good protection against damage as it is normally water proof.
Lithographic Printing
Printmaking. Printmaking is the act of creating a work of art with the intention of making reproductions of it. There are many different types of printmaking,
Unit 3: The Media of Art Chapter 8: Printmaking. Printmaking Variety of techniques developed to create multiple copies of a single image. Before 1415,
Printing Processes Including commercial digital printing KS4 Graphics.
Printing methods – what you need to know 1.Colour separation 2.Process colours 3.CMYK 4.Registration marks and the order of application of colours 5.Digital.
Welcome To Modern Printing Technologies Course Instructor: MD: ALI HOSSAIN Jr. Instructor (tech). Graphic arts institute. Dhaka-1207.
Colour Proofs What did we learn about colours?. Additive Primaries What are these primary colours? The combination of all three colours when added together.
Colour Separation The foundation of all printing processes …………… GCSE GP Exam Zone AS GP Run Slideshow Run Slideshow  A* 100%
Printing a SPOT COLOUR (5th colour) is added to the print process.
Flexography A Printing Processes ……………….. To Be Successful You Must Be Able To: A*  Justify the selection and use of Flexography to produce a graphic.
Printing Brian Russell. Exam expectations Paper/card is the compulsory material so always expect questions in exam to relate to this topic. Questions.
Relief Printing Is the oldest form of printing and is produced from a raised surface.
Communication Technology I overview. I will be able to explain the importance of communication in our technological society Essential Question: Explain.
Finishing Processes Industrial and Commercial Practice.
PRINT MAKING A Two dimensional art form that allows the production of multiple original artworks. Here are the four types..  Relief printmaking  Intaglio.
GCSE Revision Commercial Printing.
PRINTING EFFECTS Lesson Objective:
Industrial Practices GCSE Graphics AQA.
Printing Brian Russell.
Communication Technology I
Printing Terms Commercial Printing.
Viewing Graphics.
Print production.
Communication Technology I
Finishes for paper and board
Advanced Higher Graphic Communication
Communication Technology I
Introduction Production for Graphic Designers
Chapter II, Digital Color Theory: Lesson IV Digital Printing
Communication Technology I
Overview of Graphic Communications
Material Properties – Paper & Boards
The Printing Process Four-colour printing (CMYK)
Flexography or Flexographic Printing
Printing and packaging with plastic
Presentation transcript:

What do we need to know for our exam???? The AQA (our examining board) specifies the following: Quality checks such as colour registration marks, position marks. Commercial printing methods- letterpress, lithography, flexography, gravure and screen printing. Varnishing (oil, spirit, UV and water). Laminating, embossing and foil application. Multiple surface developments (nets) produced by die cutters and creasing bars. Modern Printing Methods explained. GCSE Graphic Products

The five main types of printing are: Relief- Letterpress, Block printing, Flexography (foil blocking) Planographic (flat plate printing)- Lithography & offset lithography Intaglio (etching) – Gravure, Screen Printing Xenography (dry printing)- Photocopying, Laser printing, commercial digital printing Please note that while it is good to know what these are, not all are required for the AQA syllabus. Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. Flexography Flexography is a form of relief (a raised profile) printing. The image is slightly raised, inked and the printed straight onto the substrate (technical term for paper, card or whatever is being printed on). The plate is usually made from soft rubber or plastic and uses a quick drying ink. This high speed process is well suited to a number of materials such as acetate film, polyethylene (eg supermarket bags), brown paper and newsprint. For more information visit: http://graphics.tech.uh.edu/MatProcesses/Flexography.html Flexograph machine a rubber flexograph plate Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. Offset Lithography Offset Lithography is by far the most common form of commercial printing. It accounts for over 70 % of commercial printing. Offset lithography works on a very simple principle: oil and water don’t mix. Images (words and art) are put on plates which are damped first by water the by oil-based ink. The ink sticks to the image area , the water to the non-image area which absorb moisture and repel ink. Then the image is transferred to a rubber roller and then to the substrate. This happens at an extremely fast speed as the plates are wrapped around a roller. The paper is web fed (a continuous roll). Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. What happens inside… An offset lithography machine has four of these presses, printing the cyan, magenta, yellow and black (CYMK) components of a print. Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. Advantages of offset lithography: Prints 4 colours onto flat materials It is a high quality process Very economical on medium to large production runs 500 - 500,000 It is a fast process – speeds of up to 50,000 presses per hour can be acheived on a web – fed press! Disadvantages of offset lithography Less economic than rotogravure and flexography on high volume printing 1,000,000+ Less economic than digital printing on small to medium runs 50 -100,000(although quality is slightly higher) Limited to the type of materials it can print onto – the surface must be flat. Litho would not be accurate enough for newspaper print. Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. Gravure Gravure is a printing process that uses intaglio or engraved metal plates or cylinders. The image to be printed is photo-etched onto the plate as microscopic dots. Rotogravure is a printing technique characterised by high print quality and large numbers of copies – hundreds of thousands or even many millions. Tiny ink volumes are transferred from the gravure printing cylinder to printing dots on the paper. Millions of printing dots show up to the human eye as letters/text or images The "doctor blade" is angled against the cylinder to wipe away the excess ink, leaving ink only in the cell wells Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. The main application of gravure covers a wide range of commercial products. Gravure is especially suited to work in the four colour process on relatively cheap papers in quantities over 250,000. The reason being the expense of the original printing plates which can each run into thousands of pounds. Example applications include magazines mail-order catalogues Board packaging products such as folding box cartons for food and cigarette industries, also printed video cases. Flexible packaging such as printed cellophane and polythene used in food wrapping, display and production. Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. Advantages of Gravure: It can be used for the highest quality reproductions It uses lower grade, lighter paper than lithography High speed usually 6000-10,000 prints per hour Automatic registration. Disadvantages of gravure Initial cost of rotogravure plates extremely high therefore it is only economic for very high print runs Colour correction is difficult Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. Silk Screen Printing Screen Printing is unlike any other process as it uses a stencil through which ink is pushed. The process involves forcing ink through a fine mesh (screen) which helps to spread the ink evenly. Its easy to use, versatile and requires low capital investment. Relatively cheap – on short and medium print runs – automated presses which can print, varnish or gum up to 6000 per hour. Most importantly it can print onto curvrd and uneven surfaces Modern Printing Methods explained. GCSE Graphic Products

The main stages of modern print production Prepress origination compostion Colour separation Plate production print sheet or web fed 4 colour printing Quality control Stiching binding stapling Embossing, blocking Finishing Varnish and laquer Die cutting and creasing Modern Printing Methods explained. GCSE Graphic Products

The main stages of modern print production The basic stages of modern print production are: Original artwork – photographs, illustrations and text – are scanned and entered into a computer These elements are combined into a document using page makeup or desktop publishing software Full size films are output using a high-resolution imagesetter. These could be either positives or negatives. Printing plates are made from films using a photochemical process The flexible plates are attached to the plate cylinders of a litho press and the job is printed. Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. Full Colour Printing For printing, and image is separated into its colours Cyan, Magenta, Yellow and Black (CMYK). Each colour is printed over the other as the paper (or substrate) moves through the presses. Each colour has its own press. Cyan magenta yellow black For the original go to micro.magnet.fsu.edu/.../primarycolors/ colorseparation/ Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. Quality Control The two main quality checks are: Registration Colour Density Registration can be checked by either eye or automatically and are used to check that the 4 processes are aligned properly on the substrate. Images out of alignment can appear blurred. Colour density is checked using a Densitometer, which is a hand held device that measures the density of colour. The densitometer is held over the colour bar (one colour for each of the process colours and greyscale. Registration marks at about 10X magnification A colour density bar Modern Printing Methods explained. GCSE Graphic Products

Modern Printing Methods explained. Binding Once printed the next stage is the binding of the product. The bindery is where the printed product is completed. The huge rolls of now-printed paper are cut and put together so that pages fall in the correct order. Pages are also bound together by, staples or glue, in this step of the process. A machine called a stitcher takes the folded printed paper (called press signatures) and collates them together. The final components in the stitcher machine are the knives which trim the paper to its final delivered size. A sticher machine Paper being cropped manually Modern Printing Methods explained. GCSE Graphic Products

Cutting and Folding (creasing) Most cartons (packages, boxes) require cut outs and creases in order for them to be assembled. The machine tool used on modern presses is the die cutter. Modern Printing Methods explained. GCSE Graphic Products