GOVERNMENT ENGINEERING COLLEGE, BHAVNAGAR TOPIC : INTRODUCTION TO PRESSURE VESSELS Prepared By :- 1.Aal Akash 130210119003 2. Ansari Aarif.

Slides:



Advertisements
Similar presentations
Mechanics of Materials II
Advertisements

INTRODUCTION TO PRESSURE VESSELS
Thrust bearings  Support the axial thrust of both horizontal as well as vertical shafts  Functions are to prevent the shaft from drifting in the axial.
STATICALLY DETERMINATE STRESS SYSTEMS
CTC / MTC 222 Strength of Materials Chapter 12 Pressure Vessels.
1 Thin Walled Pressure Vessels. 2 Consider a cylindrical vessel section of: L = Length D = Internal diameter t = Wall thickness p = fluid pressure inside.
Chapter -9 WEB STIFFENERS.
Pipe Supports and Restraints
CHAPTER 7 TRANSVERSE SHEAR.
Principle and Maximum Shearing Stresses ( )
Combined Loadings Thin-Walled Pressure Vessels Cylindrical Pressure VesselSpherical Pressure Vessel.
CM 197 Mechanics of Materials Chap 20: Connections
CM 197 Mechanics of Materials Chap 14: Stresses in Beams
Static Surface Forces hinge 8 m water ? 4 m.
Copyright © 2011 Pearson Education South Asia Pte Ltd
CTC / MTC 222 Strength of Materials
Mechanics of Materials – MAE 243 (Section 002) Spring 2008 Dr. Konstantinos A. Sierros.
Fluid Statics Lecture - 2.
Chapter 10 Web splice.
Pressure Vessels.
Force on Floating bodies:
CHAPTER OBJECTIVES Analyze the stress developed in thin-walled pressure vessels Review the stress analysis developed in previous chapters regarding axial.
SHELL AND TUBE HEAT EXCHANGER
BEAMS AND COLUMNS PRESENTED BY K.ROSHIN RUKSHANA.
Session 15 – 16 SHEET PILE STRUCTURES
Chapter 4 Axial Load. Saint -Venant's Principle Saint-Venant's Principle claims that localized effects caused by any load acting on a body will dissipate.
CHAPTER OBJECTIVES Analyze the stress developed in thin-walled pressure vessels Review the stress analysis developed in previous chapters regarding axial.
Mechanics of Materials II UET, Taxila Lecture No. (6)
COMBINED LOADING.  Analyze the stress developed in thin-walled pressure vessels  Review the stress analysis developed in previous chapters regarding.
Objectives  Introduce the concept of pressure;  Prove it has a unique value at any particular elevation;  Show how it varies with depth according.
Lecture 1 Stress 16 July 2007 ENT 450 Mechanics of Materials Dr. Haftirman 1 ENT 450 MECHANICS OF MATERIALS (MoM) RC. Hibbler Lecture: DR. HAFTIRMAN Teaching.
Combined Loadings Thin-Walled Pressure Vessels Stress caused by Combined Loadings.
GOVERNMENT ENGINEERING COLLEGE, BHARUCH (014) Chemical Engineering department SEM-iii Sub: fluid flow operation topic: orifice meter & rotAmeter Guid by:
UNIT 5 BRICK MASONRY.
Building Construction
FLUID FLOW FOR CHEMICAL ENGINEERING
1 Chapter 2: Application of stress EBB 334 Mechanical Metallurgy Assoc. Prof. Dr. Zuhailawati Hussain.
CHE441 Lecture: Tank & Vessel. Introduction of Vessel Applications of Vessels:  (1) as a liquid surge drum for liquid storage  (2) as a vapor/liquid.
HASMUKH GOSWAMI COLLEGE OF ENGINEERING SEM. 5 Mechanical Engineering
Stresses due to fluid pressure in thin cylinders
Shaping operations are generally divided into three groups based upon how the parent metal flows or deforms during the shaping process ,namely Bending.
Unit 42: Heat Transfer and Combustion
Rolling of Metals Rolling Processes Dr.Adel Fathy 1.
2K Cold Box Structure Analysis
Shear in Straight Members Shear Formula Shear Stresses in Beams
Poisson’s Ratio For a slender bar subjected to axial loading:
DEPARTMENT OF MECHANICAL AND MANUFACTURING ENGINEERING
G H Patel College of Engineering And Technology Design of Machine Elements cylindrical pressure vessel subjected to internal and external.
Thin-Walled Pressure Vessels Stress caused by Combined Loadings
Buckling & Stability Critical Load
Thin Walled Pressure Vessels
Chapter : 01 Simple Stresses
3 Torsion.
Chapter X: Sheet Forming (Membrane Theory) 1 Content of Membrane Analysis Basic Assumptions Static Equilibrium Equations Strain State Application 1: Hole.
INTRODUCTION TO PRESSURE VESSELS
Mechanical Design of Process
Poisson’s Ratio For a slender bar subjected to axial loading:
3 Torsion.
Copyright © 2014 John Wiley & Sons, Inc. All rights reserved.
326MAE (Stress and Dynamic Analysis) 340MAE (Extended Stress and Dynamic Analysis)
( BDA ) CHAPTER V THICK CYLINDER
Mechanics of Materials II
PLATE HEAT EXCHANGERS Gasketed plate heat exchangers
EAT 415 :ADVANCED STEEL BUILDING DESIGN PLATE GIRDER
Heat Exchangers Heat Exchangers.
3 Torsion.
Poisson’s Ratio For a slender bar subjected to axial loading:
ROOFS.
Mechanics of Materials Engr Lecture 32 Thin Walled Pressure Vessels
Copyright ©2014 Pearson Education, All Rights Reserved
Presentation transcript:

GOVERNMENT ENGINEERING COLLEGE, BHAVNAGAR TOPIC : INTRODUCTION TO PRESSURE VESSELS Prepared By :- 1.Aal Akash 130210119003 2. Ansari Aarif 130210119006

INTRODUCTION TO PRESSURE VESSELS

PRESSURE VESSELS Pressure vessels are the containers for fluids under high pressure. They are used in a variety of industries like Petroleum refining Chemical Power Food & beverage Pharmaceutical

TYPES OF PRESSURE VESSELS There are three main types of pressure vessels in general Horizontal Pressure Vessels Vertical Pressure Vessels Spherical Pressure vessels However there are some special types of Vessels like Regeneration Tower, Reactors but these names are given according to their use only.

HORIZONTAL PRESSURE VESSEL

VERTICAL PRESSURE VESSEL The max. Shell length to diameter ratio for a small vertical drum is about 5 : 1

TALL VERTICAL TOWER Constructed in a wider range of shell diameter and height. They can be relatively small in dia. and very large (e.g. 4 ft dia. And 200 ft tall distillation column. They can be very large in dia. and moderately tall (e.g. 3 ft dia. And 150 ft tall tower). Internal trays are needed for flow distribution.

VERTICAL REACTOR Figure shows a typical reactor vessel with a cylindrical shell. The process fluid undergoes a chemical reaction inside a reactor. This reaction is normally facilitated by the presence of a catalyst which is held in one or more catalyst beds.

SPHERICAL PRESSURIZED STORAGE VESSEL

MAIN COMPONENTS OF PRESSURE VESSEL Following are the main components of pressure Vessels in general Shell Head Nozzle Support

SHELL It is the primary component that contains the pressure. Pressure vessel shells in the form of different plates are welded together to form a structure that has a common rotational axis. Shells are either cylindrical, spherical or conical in shape.

SHELL Horizontal drums have cylindrical shells and are constructed in a wide range of diameter and length. The shell sections of a tall tower may be constructed of different materials, thickness and diameters due to process and phase change of process fluid. Shell of a spherical pressure vessel is spherical as well.

HEAD All the pressure vessels must be closed at the ends by heads (or another shell section). Heads are typically curved rather than flat. The reason is that curved configurations are stronger and allow the heads to be thinner, lighter and less expensive than flat heads. Heads can also be used inside a vessel and are known as intermediate heads. These intermediate heads are separate sections of the pressure vessels to permit different design conditions.

NOZZLE A nozzle is a cylindrical component that penetrates into the shell or head of pressure vessel. They are used for the following applications. Attach piping for flow into or out of the vessel. Attach instrument connection (level gauges, Thermowells, pressure gauges). Provide access to the vessel interior at MANWAY. Provide for direct attachment of other equipment items (e.g. heat exchangers).

SUPPORT Support is used to bear all the load of pressure vessel, earthquake and wind loads. There are different types of supports which are used depending upon the size and orientation of the pressure vessel. It is considered to be the non-pressurized part of the vessel.

TYPES OF SUPPORTS SADDLE SUPPORT: Horizontal drums are typically supported at two locations by saddle support. It spreads over a large area of the shell to prevent an excessive local stress in the shell at support point. One saddle support is anchored whereas the other is free to permit unstrained longitudinal thermal expansion of the drum.

TYPES OF SUPPORTS LEG SUPPORT: Small vertical drums are typically supported on legs that are welded to the lower portion of the shell. The max. ratio of support leg length to drum diameter is typically 2 : 1 Reinforcing pads are welded to the shell first to provide additional local reinforcement and load distribution. The number of legs depends on the drum size and loads to be carried. Support legs are also used for Spherical pressurized storage vessels. Cross bracing between the legs is used to absorb wind or earth quake loads.

TYPES OF SUPPORTS LUG SUPPORT: Vertical pressure vessels may also be supported by lugs. The use of lugs is typically limited to pressure vessels of small and medium diameter (1 to 10 ft) Also moderate height to diameter ratios in the range of 2:1 to 5:1 The lugs are typically bolted to horizontal structural members in order to provide stability against overturning loads.

TYPES OF SUPPORTS SKIRT SUPPORT: Tall vertical cylindrical pressure vessels are typically supported by skirts. A support skirt is a cylindrical shell section that is welded either to the lower portion of the vessel shell or to the bottom head (for cylindrical vessels). The skirt is normally long enough to provide enough flexibility so that radial thermal expansion of the shell does not cause high thermal stresses at its junction with the skirt.

THIN WALLED PRESSURE VESSELS Thin wall refers to a vessel having an inner-radius-to-wall-thickness ratio of “10” or more (r / t ≥ 10). When the vessel wall is thin, the stress distribution throughout its thickness will not vary significantly, and so we will assume that it is uniform or constant. Following this assumption, the analysis of thin walled cylindrical and spherical pressure vessel will be carried out. In both cases, the pressure in the vessel will be considered to be the gauge pressure, since it measure the pressure above atmospheric pressure existing at inside and outside the vessel’s walls.

THIN WALLED PRESSURE VESSELS The above analysis indicates that an element of material taken from either cylindrical or spherical pressure vessel is subjected to biaxial stress, i.e. normal stress existing in only two directions. Actually material of the vessel is also subjected to a radial stress, σ3, which acts along a radial line. This stress has a max. value equal to the pressure p at the interior wall and decreases through the wall to zero at the exterior surface of the vessel, since the gauge pressure there is zero. For thin walled vessels, however, the redial stress components are ignored because r / t = 10 results in σ1 & σ2 being, respectively, 5 & 10 times higher than the max. radial stress, (σ3)max = p

THIN WALLED PRESSURE VESSELS It must be emphasized that the formula derived for thin walled pressure vessels should be used only for cases of internal pressure. If a vessel is to be designed for external pressure as in the case of vacuum tank, or submarine, instability (buckling) of the wall may occur & stress calculations based on the formulae derived can be meaningless.