1. Make sure supply voltage is off, unplug the USB, and close the GUI.

Slides:

Advertisements

Similar presentations

Test Procedure For INA226EVM

Advertisements

Connecting Your Computer Monitor Cable Electrical power for monitor.

This presentation is intended to assist you in troubleshooting basic problems that can occur with hardware and software. NOTE: This presentation contains.

Presenting A Power Point Program. Computer Checklist Computer Checklist Power Cord Mouse Computer.

Interfacing Project. Computer Controlled Car Left Headlight – D0 Right Headlight – D1 Left Taillight – D2 Right Taillight – D3.

PC ADXL362Z- DB REV 2 USB cable 1. After turning the SW4 to VU, I can see follow picture. J1 : Ext Bat side J2 : USB side COM4.

KC705 Power Bus Monitoring

How to Set Up a Projector and SmartBoard

Laura Morrissey. Setting up and Delivering a Multimedia Presentation.

Classroom Presentation Comp 17, Florian Utchitel.

Next Keep all food and drinks away from computer and equipment—liquid may spill and cause an electrical shock or the computer not to operate properly.

Vex 1.0 © 2005 Carnegie Mellon Robotics Academy Inc. CAN I MAKE MY OWN SENSOR 2 This lesson will explain how to hook a standard dial potentiometer into.

VC707 Power Bus Reprogramming

Dr. Hoganson CSIS HC11 Demo Program This is our first lab using the 68HC11 microcontroller. We will “talk” to the microcontroller from a PC, run.

Vex 1.0 © 2005 Carnegie Mellon Robotics Academy Inc. Touch Sensor This lesson will explain how to hook a standard micro switch into the Vex system to function.

18 - Winter 2003 EE EE 766 Computer Interfacing and Protocols 1 USB (Universal Serial Bus) Need for “Plug and Play” capability for PC peripherals outside.

Embedded Programming and Robotics

Get to know your WOW (Workstation On Wheels). There are 3 types of WOW’s Howard Cart SV21 SV22.

Configuring a PC. Installing the Mother board To Install the Mother board, fit it into the computer casing. You will then need to Insert 24 pin ATX power.

Cablesand Connectors It is important and necessary that ALL cables are coiled before being turned in.

What is USB? Prototyping Unit.

Step 1: Right click, “My computer” select properties, Select Hardware >Device Manager > Other Device > USB Serial Converter, then Right Click and select.

Jeff Branson Education Outreach Coordinator Derek Runberg Curriculum Curator Getting.

High Speed Data Converter University

MICRO CONTROLLER MODULE 1. Learning Objectives Name some gadgets that use microcontrollers. Define a microcontroller. Differentiate between a computer.

SE3910 Week 2, Class 1 Today Basic Circuits Other ??? Tomorrow Lab 2, S365 (Complete prelab BEFORE) Thursday See ScheduleSchedule SE-2811 Slide design:

KB: CAUSES:  Over charging of the device  Sync cable issues  Power source does not supply enough energy on the device (laptop is not plug in.

FIRST GADGETEER PROJECT. Where are you? Making a VS project Parts of a C# program Basics of C# syntax Debugging in VS Questions? 2.

Tweaking Your Simon Adding a photoresistor and changing code Instruction by Pete Lewis.

WinTV-USB Image-capture device. The image capture device is connected to the computer through the USB cable, and the existing video cable from the video.

Programming the Geiger Counter Board 1. Arduino Files Go to and download the latest Arduino.

Issues with USB communication to pump box Sonya Collier Qi Zhang’s Group – UC Davis.

Software Download Guide. 2/2/2016 Steps 1. Before you start to download software,please install USB driver(Folder: USB Driver) firstly. – Install “ InstallDriver.exe.

Updating USB2ANY firmware

Ports and Connectors By Karina Hackett Overview: Ports are also known as sockets, and are located at the back of a system unit. Connectors are the parts.

Promethean ActivClassroom

By Joshua Shaw.  Now that we have a program, we should see how it works in the real world  To do this we need the Cortex and the orange USB cable 

 Charging and Syncing the iPod Touch Cart Lesson 2.

Downloading the bitstream Connect parallel port to PC.

Insert your Thumb Drive into the USB slot

2. Car Pad 4 backside cable connection port definition.

Implementing VHDL Modules onto Atlys Demo Board

THS5671EVM Test with TSW1400EVM

Brother Printer Support Helpline Number Ireland:

Automatic lights.

Introduction to Arduino Microcontrollers

How to Fix HP Printer Ink System Failure 0xc19a0042

Lighting LEDs with a RASPBERRY PI

An introduction to the Raspberry Pi

مقدمة في الاردنيو د فضل الاكوع.

Basic Troubleshooting Tips for HP Scanjet Enterprise 7000 s2

How to Fix MagicJack Connection Errors?. MagicJack is a VOIP based phone service product that works by using the pre-existing internet connection to make.

Welcome to Digital Electronics using the Arduino Board

ADC32RF45 Testing.

NI Data Acquisition (DAQ) Wiring and Connections

IspVM quicky START ICPDAS CO.,LTD.

How to Connect a Dell Printer to Your PC. Connecting a Wired Printer on Windows 1. Set your printer near your PC.

Updating the Victor Stream

Setting up your computer

Having fun with Arduino

Aeroponic Engineering and Vertical Farming

How to Generate a Header File for TAS5805M in PPC3

Task 1 You are going to use the Makey Makey arrow inputs to create a joystick / games controller. Step 1: Connect Makey.

Connection between PC(host),502B and EZ USB(device)

Downloading to the NXT requires the correct hardware setup

HP Printer In Error State

HP Printer in Error State Windows 10 HPsupport247.

HP Printer in Error State Windows 10. This problem, usually occur after your system gets new updates causing the connected device to stop the job. When.

Fix Canon Printer Offline Mac Error | Call | 24/7 Support

Presentation transcript:

1. Make sure supply voltage is off, unplug the USB, and close the GUI. 2. Plug in the USB cable to the EVM through the J1 micro-USB connector. 3. Plug in the other end of the USB cable to the computer USB port. 4. Ensure that VSYS (3.3 V to 5 V) is connected to the pin labeled VSYS of P16 and that GND is connected to the pin labeled GND of P16. 5. Set supply voltage to between 3.3 V and 5 V with an appropriate current limit. Turn on supply voltage. The RESET_OUT LED (D1), LDOVRTC_OUT LED (D3), POWER_HOLD LED (D5), LDOVRTC_OUT, and POWER_GOOD (D2) should light.

To Host PC GND 5V

6.Start GUI 7.Click bit of register on GUI (For example, The red circle below)

8.Errer occur 9.Click [Continue] bottom

8.Error does not occur after clicking [Continue] bottom at first error.