EXERCISE 1.4 MICROMETER SCREW GAUGE. D. 2.73 mm C. 5.23 mm B. 3.23 mm A. 0.23 mm    Q1. The diagram shows a micrometer screw gauge. Which reading is.

Slides:

Advertisements

Similar presentations

Measurement Quiz Click here to start Scoring

Advertisements

Rules of Divisibility. Divisible by 2? If the last digit is even then the number is divisible by 2. Even digits are 0, 2, 4, 6 and 8 (yes zero is even!)

Microscopic Measurement Q: How do you measure the size of a microscopic specimen? A: You will get a close estimation using the following technique…

Prime and Composite Numbers

Exercise Exercise3.1 8 Exercise3.1 9 Exercise

Exercise Exercise Exercise Exercise

Exercise Exercise Exercise Exercise

Exercise Exercise6.1 7 Exercise6.1 8 Exercise6.1 9.

Math 015 Section 6.6 Graphing Lines. Objective: To check solutions of an equation in two variables. Question: Is (-3, 7) a solution of y = -2x + 1 ? y.

Using the Diagram It Template Copy this presentation to your hard drive. There are two sets of templates: Slides #3 & 4 for a flow chart Slides #5 & 6.

SYMMETRY Write the Dictionary Definition of each of the following terms Line Symmetry: ___________________________ _______________________________________.

CREATED BY: Farisa Himatin Nihayati ( ). SUBJECT OBJECTIVES EVALUATION CLOSURE.

Use intercepts to graph an equation

EXAMPLE 1 Finding the Area of a Parallelogram SOLUTION = Abhbh Write the formula for the area of a parallelogram. = 10 Simplify. ANSWER The area of the.

EXAMPLE 1 Write an equation of a circle Write the equation of the circle shown. The radius is 3 and the center is at the origin. x 2 + y 2 = r 2 x 2 +

Write and graph a direct variation equation

Use of Vernier Caliper Vernier Caliper can be used to measure diameter, thickness very accurately. The Mission Covenant Church Holm Glad College.

PAPER 3 SECTION A QUESTION NO. 1. What instrument will be tested? Lever balance ? Tripple beam balance ? Thermometer ? Micrometer screw gauge ? Manometer.

EXAMPLE 1 Find slopes of lines in a coordinate plane Find the slope of line a and line d. SOLUTION Slope of line a : m = – 1 Slope of line d : m = 4 –

EXAMPLE 4 Solve a real-world problem You are building a frame for a window. The window will be installed in the opening shown in the diagram. Carpentry.

2.3 Introduction to Functions

 A -  B -  C -  D - Yes No Not sure.  A -  B -  C -  D - Yes No Not sure.

Small Hole Gauges & Telescoping Gauges. Small Hole Gauges These gauges are used to measure small holes that you need to know the exact measurement.

Mohammad Dedyardie Takong 08B0904. At the end of the lesson, you should be able to:  State the use of a micrometer screw gauge  Master the techniques.

EXAMPLE 2 Find the LCD of rational expressions Find the LCD of the rational expressions. r r 2 a., 1 4r4r SOLUTION a. Find the least common multiple.

Radians, Arc Length and Sector Area. Radians Radians are units for measuring angles. They can be used instead of degrees. r O 1 radian is the size of.

Micrometer Screw Caliper anvilspindle barrel thimble ratchet.

Team trivia 3 Rounds Bid 1, 3 or 5 points on each question (must use each point value per round)

Use point-slope form to write an equation EXAMPLE 3 Write an equation in point-slope form of the line shown.

EXAMPLE 3 Prove the Vertical Angles Congruence Theorem

Measurement with the Microscope

EXAMPLE 4 Rewrite polynomials Divide 5y + y by 2 + y. Rewrite polynomials. Multiply y and y + 2. y 2 + 2y Subtract y 2 + 2y. Bring down 4. 3y + 4.

MEASURING LENGTH AND TIME

Quadratics 5 Discriminant, Problem Solving, Intersecting Graphs.

Hazrin Shah Bin Hj Azahari 08B0912 Mohammad Dedyardie Takong 08B0904 LENGTH.

AS Physics – Physics: the science of measurement Mr Ewart v1 07/ Making measurements precisely Measuring instruments From smaller than the nucleus.

Get Precise Measurements. Micrometer Caliper Depth Gauge Micrometer.

Money Quiz!!!!. Write the question number and the answer in your maths book. How much money is shown? 1.

Money Quiz!!!!. Write the question number and the answer in your maths book. How much money is shown? 1.

ANSWERS!. Completing the Square Level 1 Answers Completing the Square Level 2 Answers.

SATMathVideos.Net If Line A passed through points (1,1) and (3,2). And Line B (not shown) is perpendicular to Line A. Which equation represents Line B?

Warm-Up Exercises GUIDED PRACTICE for Example 1 Rewrite the conditional statement in if-then form. 1. All 90 ° angles are right angles. ANSWER If the measure.

EXAMPLE 1 Solve a system graphically Graph the linear system and estimate the solution. Then check the solution algebraically. 4x + y = 8 2x – 3y = 18.

EXAMPLE 1 Write an equation of a circle Write the equation of the circle shown. SOLUTION The radius is 3 and the center is at the origin. x 2 + y 2 = r.

Jeopardy Q $100 Q $100 Q $100 Q $100 Q $100 Q $200 Q $200 Q $200

The reading is 7.38 mm. The reading is 7.72 mm.

Model Multiplication Name: _______________________________

Model Multiplication Name: _______________________________

Introduction to Functions

Maths for Biology: Magnification

Multiplying and Dividing Rational Expressions

סדר דין פלילי – חקיקה ומהות ההליך הפלילי

Exercise: Logical operators

Start Finish Find the solution 42 out of out of 2200

Money Quiz!!!!.

Find an unknown interior angle measure

Solving One-Step Equations

The Mission Covenant Church Holm Glad College

You must show all steps of your working out.

9/18/ Bell Work Write and answer the following questions.

Ordered Pair – (11 - 2) CS-708.

Completing the Square pages 544–546 Exercises , – , –2

Use of Vernier Caliper Vernier Caliper can be used to measure diameter, thickness very accurately.

Solution Free Body Diagram.

Presentation transcript:

EXERCISE 1.4 MICROMETER SCREW GAUGE

D mm C mm B mm A mm    Q1. The diagram shows a micrometer screw gauge. Which reading is shown Yes, well done! Solution: = 2.73

Q2. What is the reading on the micrometer screw gauge? Answer: 3.97 mm Solution: = 3.97 mm

Q3. What is the reading on the micrometer screw gauge? Answer:6.63 mm Solution: = 6.63 mm

Q4. What is the reading on the micrometer screw gauge? Answer: 4.06 mm Solution: = 4.06 mm

Q5. What is the reading on the micrometer screw gauge? Answer: 1.25 mm Solution: = 1.25 mm