DENSO Denso Manufacturing Michigan Inc. Production Control Supplier Manual Section Packaging Title Returnable Packaging Requirements Control No. PKG-005 Purpose: Standards: Date Issued : Date Revised : 2/26/14 To define DMMI’s returnable packaging requirements. (1) G:PRD_CTRL/SUPPLIER MANUAL UPDATES 2009/SUPPLIER MANUAL UPDATES 2011/ Returnable Packaging Requirements DMMI’s goal is to minimize the amount of packaging in the system by: Minimizing inventories at DMMI and the supplier. Maximizing turns. A)Container Requirements Containers must be designed for manual handling. * Two cardholders per container are required, on adjacent sides. Cardholders must be 8.75” x 4.25”. Molded polypropylene cardholders or open-top vinyl holders are acceptable. Side-load cardholders are prohibited. Containers must cube 48” x 45” pallet, specialty totes must be approved by DMMI. Use of lids is prohibited, unless otherwise specified by DMMI for part quality. Container weight cannot exceed 30 pounds when full. Part orientation in tote should be simple, consistent, avoiding excessive reach, and not exceeding the tote nesting line (see photo). Nesting, if applicable, must be done in such a way that it will be maintained during shipping, see photo. Nest OKNest No Good

DENSO Denso Manufacturing Michigan Inc. Production Control Supplier Manual Section Packaging Date Issued : Date Revised : 2/26/14 Title Returnable Packaging Requirements Control No. PKG-005 (2) G:PRD_CTRL/SUPPLIER MANUAL UPDATES 2009/SUPPLIER MANUAL UPDATES 2011/ Returnable packaging Requirements Denso owned containers will be identified with a unique pkg. code: For example: TMM-SPC-LS4D-DA TMM = Customer code (only used for A-Parts) SPC = Supplier code LS4D = Type of container; 4D = size of container DA = Designates type of dunnage (only used if needed) Supplier-owned containers must be marked with supplier name and plant location. B) Approved Container Sizes Small Components Large Components Levers, clips, ect Cases, long parts, ect Tote size PKG Code Tote size PKG Code 12 x 7 x 5 LS8Z 32 x 15 x 7 LS7H or GT7H 12 x 15 x 4 LS9L 32 x 15 x 14 LS4H or GT4H 12 x 15 x 5 LS8L 45 x 16 x 9 GT6I 12 x 15 x 7 LS7L 45 x 16 x 14 GT4I 12 x 15 x 9 LS6L 45 x 16 x 20 GT3I 12 x 15 x 4 LS9D 24 x 15 x 7 LS7D 24 x 15 x 9 LS6D 24 x 15 x 11 LS5D C) Dunnage Requirements Returnable material should be used. Material must be recyclable. Individual parts cannot be bagged or wrapped unless otherwise specified. Multiple layers of dunnage in container is prohibited unless, otherwise specified. Recycled content must not exceed 50%, unless certified regrind is used.

DENSO Denso Manufacturing Michigan Inc. Production Control Supplier Manual Section Packaging Date Issued : Date Revised : 2/26/14 Title Returnable Packaging Requirements Control No. PKG-005 D) Pallet Requirements Pallets must be returnable. * If returnable pallets are not available the use of wood pallets is acceptable. Cardboard lids would be required in this situation. Must be AIAG standard 48” x 45”, with standard fork openings. Must be four-way entry. Vac-tray style pallets must be designed to support the weight of the product. Recycled content must not exceed 50%, unless certified regrind is used. Pallet skids cannot exceed 35 lbs. unless approved by DMMI. Supplier owned pallets must be marked with supplier name and plant location. End of Procedure G:PRD_CTRL/SUPPLIER MANUAL UPDATES 2009/SUPPLIER MANUAL UPDATES 2011/ Returnable packaging Requirements * Denotes change (3)