1. Detention Cisterns for CSO Control Bob Spencer Seattle Public Utilities www.seattle.gov/util/greeninfrastructure www.seattle.gov/util/RainWise

2. 2 Partnering with the Community: Residential RainWise Seattle Public Utilities

3. 3 Ballard North Union Bay Interbay Evaluating additional basins –Barton (lead by King County) –Genesee –Henderson –Montlake –Lake Union –West Seattle –Fremont/Wallingford Green Stormwater Infrastructure Target Basins

4. The Rain Wise Toolbox Rainfall: - slow it - spread it - filter it - soak it in.

5. Locating and Planning Cistern Installations for Stormwater Management Downspout Screened inlet Overflow Drain to garden hose For more information, see the Cistern factsheet and other resources at www.seattle.gov/util/rainwise

6. Seattle Public Utilities 6 Is this a good site for a cistern? A cistern installation needs:  A level location near a downspout, outside (not inside building)  A solid base (6” of packed 3/8 crushed rock)  To allow ingress and egress for people  Don’t block doors, windows, vents, or utilities accesses  A safe place to discharge the overflow, a minimum of: –5 feet from your home (with no basement) –10 feet from your home, if you have a basement –5 feet from a property line, and 10 feet from neighboring buildings –or connect overflow to sewer (requires side sewer permit – call DPD at # on RainWise factsheet)

7. Constructing Cistern Installations for Stormwater Management www.seattle.gov/util/rainwise Downspout Screened inlet Overflow Drain to garden hose

8. Example Cistern Layout Follow manufacturer’s instructions! Gutter (ideally with leaf screens) Downspout Self-cleaning leaf filter Screened inlet Finer screens keep more dirt out. Overflow – 3-4 inch pipe, with ”P” trap Cistern – typically heavy plastic or fiberglass Disperse overflow into landscape A minimum of: - 5 ft. from house, or 10 ft. with basement - 5 ft. from property line, - 10 ft. from neighboring buildings Level foundation – 6 inches of packed 3/8” crushed rock, or concrete block, over packed subsoil Drain – 3/4 inch pipe with faucet Connect garden hose to drain to yard in winter. Close faucet in May to store water for summer. screen Cleanout plug (3 to 4 inch diameter) Clean tank annually by squirting hose into inlet and cleanout, and scrubbing with long- handled brush.

9. Seattle Public Utilities 9 What makes a cistern work for storm water detention? The “low-flow orifice” In this case, a faucet that’s left open October-May, to allow tank to drain out between storm events, so there’s space to store and slowly release the next rainfall. Cisterns must have a ¼-inch orifice plumbed to the landscape or sewer. For non-rebate homeowner projects, a faucet & garden hose works fine. If the cistern is full when it rains hard, it provides no stormwater benefit – it must be able to drain between storms.

10. 10 Step 1: Build a level foundation to support a cistern full of water Excavate topsoil at least 3 inches: create hard a level surface – don’t place on un-compacted fill Pack subsoil with hand tamper or mechanical compactor Place a level foundation: –Ground-contact-treated lumber box, filled with 6 inches of 3/8 crushed rock, well compacted. May top with 1 inch of sand or fine gravel to get smooth level surface under cistern. –Concrete blocks or heavy (min. 3-inch thick) pavers – perfectly level on top –Existing concrete pad, if level. (Installing a new concrete pad would require a building permit.)

11. Seattle Public Utilities 11

12. Seattle Public Utilities 12

13. Seattle Public Utilities 13 Step 2: Place cistern tank Don’t block opening of doors & windows, emergency egress, vents, utilities access, etc. Plan for downspout flow to cistern, and overflow routing Consider appearance and consult neighbors Follow manufacturer’s instructions If the tank is taller than it is wide, secure for earthquake safety (usually impractical, so best not to use tall, narrow tanks) Downspout Screened inlet Overflow Drain to garden hose

14. Seattle Public Utilities 14 Connect additional tanks, if used

15. Seattle Public Utilities 15 Step 3: Install screened inlet, to keep debris and mosquitoes out At minimum, wrap and secure aluminum screen over inlet opening Additional protection against clogging: –Gutter screens and wire cages in gutter outlets to exclude leaves –Self-cleaning leaf excluder in downspout run to cistern – commercially available or home- assembled – Google “Downspout filters, screens” –Divert dirtier initial flow after dry period: Google “First flush diverters” “Roof washers” or “Cistern Installation” for ideas

16. Seattle Public Utilities 16

17. Seattle Public Utilities 17

18. Seattle Public Utilities 18

19. Seattle Public Utilities 19 Step 4: Make gutter connections 3-4” Aluminum, ABS, or PVC NDS pipe Secure all connections with stainless steel screws & silicone seal, or glue Strap & support as needed May put a self-cleaning leaf excluder in line: typically a sloped screen so leaves are pushed aside Arrange so water falls into screened inlet, with access to clean screen

20. Seattle Public Utilities 20 Step 5: Install overflow pipe that’s as big as the inlet pipe Watertight bulkhead fitting at top, or internal overflow riser, or both (if less that 3 inch) Must be big enough to carry full gutter flow once cistern fills – 3 to 4-inch diameter Install “P” trap somewhere, to prevent mosquito and rat entry

21. Seattle Public Utilities 21 Step 6: Extend overflow pipe to a safe discharge point 5’ from house or 10’ if basement 5’ from property line, 10’ from neighboring buildings Rubber “hubless” unions protect against breakage, allow maintenance Use rocks or gravel to prevent erosion and disperse overflow into landscape If reconnected to sewer, requires a permit – call DPD

22. Seattle Public Utilities 22

23. Seattle Public Utilities 23

24. Seattle Public Utilities 24 Consider appearance Can screen cistern with fencing, latticework, cedar or bamboo wrap, etc. Plastic paint works on ABS & PVC pipe Blend with existing architectural finishes Consult with neighbors South Seattle Community College cistern overflowing to rain garden in a downpour, Nov. 2009

25. Seattle Public Utilities 25

26. Seattle Public Utilities 26

27. Million Dollar Idea: Chia-Tank

28. I wanna rock! Seattle Public Utilities 28

29. Seattle Public Utilities 29 Step 7: Install drain valve for use as “low-flow orifice” Use oversize (1-3”) bulkhead fitting, so entire fitting can be removed for cleaning tank. Or install separate cleanout plug. “Hose bib” garden hose faucet Connect garden hose, and run it to safe discharge point to drain cistern slowly between storms Close faucet in May to store water for summer. Open again in October to detain and slowly drain winter storm water

30. Low-flow orifice plumbing for Code-permitted cisterns (example from Lakewood project) Seattle Public Utilities 30

31. Seattle Public Utilities 31

32. Seattle Public Utilities 32

33. Questions? Guide, factsheets, and design tools: www.seattle.gov/util/RainWise www.seattle.gov/util/RainWise Bob Spencer David McDonald Seattle Public Utilities

34. 34