1. 1 | INALA TECHNOLOGIES ECS-L TESTING : VERSION 1.0

2. 2 | ECS-L TEST – FLOW CHART ECS-L Test Preparation Insert SIM in to MODEM Connect SAM1.5 to ECS-L Inter Connect the 2 RS232 Ports of ECS-L Inter connect 2 RS485 Ports of ECS-L Power up ECS-L with or without SAM1.5 ECS-L Test Set- up Configure ECS-L with test Configuration Configure Test Server IP address. ECS-L Test with Server Server Auto detects communication from new ECS-L unit and IP Address Server runs test scrip to check the following: ECS-L Serial Number Communication between the 2 RS232 ports Communication between the 2 RS485 ports Generate and email a PDF test certificate to predefined list of email addresses. If test was successful or not and ECS-L is working correctly or not. Configure ECS-L with Vodacom Config If test is unsuccessful and ECS-L is not working a test certificate will be issued indicating the part of the test that failed Print out Test Certificate and Power Down unit and Package with Test Certificate Do fault Finding Repair fault Repeat process Test Fail Test Pass

3. 3 | ECS-L - COMMUNICATION CONNECTIONS SAM Training ECS Software Management Platform RS232 test cable RS232 SAM1.5 GPRS to Management Platform RS485 Test Cable RS232 Test cable Use Staight RS232 Ribbon Cable – IDC 10way to IDC 10 Way. Plug into Port3 DTE and Port5 DCE RS485 Test Cable Wire Port1 TX to Port4 TX Port1 RX to Port4 RX Port1 GND to Port4 GND

4. 4 | ECS-L – PHYSICAL PORT NUMBERS SAM Training PORT 5 - RS232 (ECT) PORT 3 - RS232 PORT 1 – RS485 PORT 2 - RS232 PORT 4 - RS485

5. 5 | SOFTWARE FOR ECS-L (CONFIG TO BE LOADED BEFORE TEST) SAM Training Communication Controller Software (ECT): Current Version ECT – V2.28 ECT Version is viewed on the top left corner as indicated with the yellow circle EG: “ITMS-C Ver 2.28” Current Version Firmware – V2024 Firmware Version is viewed on the button left corner as indicated with the Red circle EG: “S/W: 2.0.2.4” IP address is automatically allocated to sim card and is displayed. Input APN name “vodameter” and Server IP 10.85.71.146

6. 6 | SOFTWARE FOR ECS-L (CONFIG TO BE LOADED AFTER TEST) SAM Training Communication Controller Software (ECT): Current Version ECT – V2.28 ECT Version is viewed on the top left corner as indicated with the yellow circle EG: “ITMS-C Ver 2.28” Current Version Firmware – V2024 Firmware Version is viewed on the button left corner as indicated with the Red circle EG: “S/W: 2.0.2.4” IP address is automatically allocated to sim card and is displayed. Input APN name “vodameter” and Server IP 1.1.1.1

7. 7 | ECS-L2 - COMMUNICATION CONNECTIONS SAM Training ECS Software Management Platform RS232 test cable RS232 SAM1.5 GPRS to Management Platform RS485 Test Cable RS232 Test cable Use Staight RS232 Ribbon Cable – IDC 10way to IDC 10 Way. Plug into Port3 DTE and Port5 DCE RS485 Test Cable Wire Port1 TX to Port4 TX Port1 RX to Port4 RX Port1 GND to Port4 GND

8. 8 | ECS-L2 – PHYSICAL PORT NUMBERS SAM Training PORT 5 - RS232 PORT 2 – Isolated RS485 PORT 4 – RS232 PORT 3 - RS232 PORT 1 - RS485 * The physical port that is connected to the SAM must be selected as the “Event PORT” USB PORT – ECS2 ECT Port 12VDC Power GND +12vdc

9. 9 | ECS(ETH/GPRS - COMMUNICATION CONNECTIONS SAM Training ECS Software Management Platform RS232 test cable RS232 SAM1.5 GPRS to Management Platform RS485 Test Cable RS232 Test cable Use Staight RS232 Ribbon Cable – IDC 10way to IDC 10 Way. Plug into Port3 DTE and Port5 DCE RS485 Test Cable Wire Port1 TX to Port4 TX Port1 RX to Port4 RX Port1 GND to Port4 GND

10. 10 | ECS(ETH/GPRS – PHYSICAL PORT NUMBERS SAM Training PORT 1 – RS485 PORT 2 – Isolated RS485 PORT 3 – RS232 PORT 4 – RS232 PORT 5 – RS232 PORT 6 – RS232 PORT 7 – RS232 * The physical port that is connected to the SAM or Access Control must be selected as the “UDP PORT”

11. 11 | ECS(ETH/GPRS) & ECS-L(GPRS) CONFIG TO BE LOADED BEFORE TEST SAM Training Communication Controller Software (ECS2 ECT): Current Version ECT – V1.4 ECT Version is viewed on the top left corner as indicated with the yellow circle EG: “ECS2 ECT V 1.4” Current Version Firmware – V1.4 Firmware Version is viewed on the bottom as indicated with the Red circle EG: “Build: 1.4” IP address is automatically allocated to sim card and is displayed. Enable: 1.GPRS Modem 2.Input APN name “vodameter” 3.UDP Server - 10.85.71.146 4.Input Regional Server IP for applicable region and UDP port “299” 5.Set Port configuration 6.Click on Update unit 7.Wait for unit to complete updating

12. 12 | ECS(ETH/GPRS) & ECS-L(GPRS) CONFIG TO BE LOADED AFTER TEST SAM Training Communication Controller Software (ECS2 ECT): Current Version ECT – V1.4 ECT Version is viewed on the top left corner as indicated with the yellow circle EG: “ECS2 ECT V 1.4” Current Version Firmware – V1.4 Firmware Version is viewed on the bottom as indicated with the Red circle EG: “Build: 1.4” IP address is automatically allocated to sim card and is displayed. Enable: 1.GPRS Modem 2.Input APN name “vodameter” 3.VPN Server - 1.1.1.1 4.Input Regional Server IP for applicable region and UDP port “299” 5.Set Port configuration 6.Click on Update unit 7.Wait for unit to complete updating

13. 13 | HOW TO TEST SAM COMMUNICATION SAM Training Pre Test Instructions:: 1.Make sure Communication cable is connected between communication controller and SAM. 2.Make sure communication cable is connected between PC and communication controller 3.Make sure PC IP address is within range of the communication controller – only applicable with the ECS(E1/Ethernet) communication controller. Open the SAM ECT 1.Select TCP 2.Insert the IP address of the communication controller 3.Insert the applicable port number, usually 301 or 310 4.Click on OK and communication will commence. NOTE : If this is a SAM2 unit not running on V3.03 firmware it will be necessary to log into the SAM2 unit using an RS232 cable to enable “RS485” on the SAM2 unit.

14. 14 | HOW TO TEST ACCESS CONTROL COMMUNICATION SAM Training Pre Test Instructions:: 1.Make sure Communication cable is connected between communication controller and the Access Controll. 2.Make sure communication cable is connected between PC and communication controller 3.Make sure PC IP address is within range of the communication controller – only applicable with the ECS(E1/Ethernet) communication controller. Open the Access Control ECT 1.Select TCP 2.Insert the IP address of the communication controller 3.Port Number is set to 301 as a default 4.Click on Connect and the Logon and communication will commence Test. 5.Click on “Open Door” 6.Click on “Get Version 7.Click on “Get Time” 8.Click on “Log off”

15. 15 | CLICK TO EDIT MASTER TITLE STYLE THANK YOU