Presentation is loading. Please wait.

Presentation is loading. Please wait.

North Slope Training Cooperative © North Slope Training Cooperative—revised May 2012. All rights reserved. Electrical Safety for Non- Electrical Workers.

Similar presentations


Presentation on theme: "North Slope Training Cooperative © North Slope Training Cooperative—revised May 2012. All rights reserved. Electrical Safety for Non- Electrical Workers."— Presentation transcript:

1 North Slope Training Cooperative © North Slope Training Cooperative—revised May 2012. All rights reserved. Electrical Safety for Non- Electrical Workers (Unqualified) NSTC-10

2 © North Slope Training Cooperative—May 2012. All rights reserved. Course Overview 2

3 © North Slope Training Cooperative—May 2012. All rights reserved. Administration and Safety Emergency Procedures Restrooms/Breaks/Smoking Safety Minute 3

4 © North Slope Training Cooperative—May 2012. All rights reserved. Introductions Name Company and/or position Experience working in areas where there are potential hazards from energized equipment, or power tools. 4

5 © North Slope Training Cooperative—May 2012. All rights reserved. Goal To provide non-electrical (unqualified) employees with the knowledge to recognize electrical hazards and take appropriate measures to protect themselves against injury or death. 5

6 © North Slope Training Cooperative—May 2012. All rights reserved. Objectives Distinguish between an affected person, unqualified person, and qualified person as it pertains to electrical safety. List the potential electrical injuries/hazards related to using power tools and working around energized equipment. Explain basic electrical concepts that are important to understanding why electricity is dangerous. 6

7 © North Slope Training Cooperative—May 2012. All rights reserved. Objectives Explain safe work practices for using power tools/equipment and working around energized equipment. Explain the general rules for responding to an electrical emergency. 7

8 © North Slope Training Cooperative—May 2012. All rights reserved. Standards and Terms 8

9 © North Slope Training Cooperative—May 2012. All rights reserved. Electrical Standards OSHA 29 CFR 1910.331-333: Subpart S: Safety Related Work Practices for Qualified and Unqualified Persons OSHA 29 CFR 1926 Subparts I and K National Electrical Code (NFPA 70) Alaska Safety Handbooks (ASH & BP ASH) ASH, pages 22-24; 28-29; BP ASH, pages 59-61; 214 9

10 © North Slope Training Cooperative—May 2012. All rights reserved. Key Terms What are the correct definitions of the following terms and why are they important? Which of these definitions fit your job responsibilities? Affected Employee Unqualified Person Qualified Person ASH, page 189, 195; BP ASH, page 237, 244 OSHA 29 CFR 1910.331(a) 10

11 © North Slope Training Cooperative—May 2012. All rights reserved. Basic Electrical Concepts 11

12 © North Slope Training Cooperative—May 2012. All rights reserved. How Electricity Works When you turn on a light switch, current flows from the generating source through a conductive material (wires) to the area of demand or load (light bulb). Current will only flow if a complete path or circuit is provided from the source, through the load, and back to the source. The electrical pressure that causes current to flow is voltage. A conductor connected to a power (voltage) source is said to be energized. 12

13 © North Slope Training Cooperative—May 2012. All rights reserved. Electricity Flow 13

14 © North Slope Training Cooperative—May 2012. All rights reserved. Simple Electrical Circuit Open 14

15 © North Slope Training Cooperative—May 2012. All rights reserved. Simple Electrical Circuit Closed 15

16 © North Slope Training Cooperative—May 2012. All rights reserved. Ohm’s LawV= IR For electrons to move in a particular direction, a potential difference must exist between two points within the circuit. This difference is measured in volts (V). Current (I), the continuous movement of electrons past a given point, is measured in amperes. All conductors resist the flow of current, some more than others. Resistance (R) is measured in ohms. 16

17 © North Slope Training Cooperative—May 2012. All rights reserved. Types of Current Direct current (DC) flows in one direction with constant pressure (voltage). Examples: battery-operated tools or equipment; motors used in special process applications Alternating current (AC) periodically reverses it’s direction of flow according to a cycle. In the U.S., AC current is 60 cycles per second. Examples: circuits for lights, appliances, tools and equipment 17

18 © North Slope Training Cooperative—May 2012. All rights reserved. Conductors Electrical conductors are low resistance materials which readily allow electrons to pass through. Examples are copper, aluminum, iron, steel, water with impurities, electrolytes, and concrete. Because all conductors resist electron flow to some extent, when the current overcomes the resistance, it creates heat. The photo above shows copper wires covered by a glass insulator. 18

19 © North Slope Training Cooperative—May 2012. All rights reserved. Insulators Because conductors get hot, they need to be insulated to prevent fires. Materials such as glass, ceramics, plastics, rubber-like polymers, and porcelain have a natural resistance to electrical flow and make good insulators. Copper wires sheathed in plastic and enclosed in an aluminum cable Copper wires sheathed in plastic 19

20 © North Slope Training Cooperative—May 2012. All rights reserved. Electrical Safety Devices Circuit breakers and fuses: Automatic tripping devices which control the amount of current flowing in the circuit and prevent overloaded circuits which could cause fires. They are designed to protect the equipment from damage. Ground fault circuit interrupter (GFCI): A safety device which detects current leakage from a circuit to ground (ground fault) and shuts off the current. It is designed to protect the person not the equipment. 20

21 © North Slope Training Cooperative—May 2012. All rights reserved. Bonding Bonding is the process of connecting two or more conductive objects to each other by means of a conductor to minimize potential differences between conductive objects. Bonding equalizes the potential between objects. BP ASH, pages 198-199; 238 21

22 © North Slope Training Cooperative—May 2012. All rights reserved. Grounding Grounding is the process of connecting one or more conductive objects to the ground to minimize potential differences between objects and the ground. Grounding dissipates an electric charge to ground. BP ASH, pages 198-199; 241 22

23 © North Slope Training Cooperative—May 2012. All rights reserved. Bonding and Grounding This is an example of grounding two objects with the earth and bonding them to each other. BP ASH, pages 198-199; 238; 241 23

24 © North Slope Training Cooperative—May 2012. All rights reserved. Electrical Hazards and Injuries 24

25 © North Slope Training Cooperative—May 2012. All rights reserved. Potential Electrical Hazards Contact with overhead transmission lines Defective insulation – exposed wiring or electrical parts Overloaded circuits Ungrounded or improperly grounded circuits Wet conditions Defective tools and equipment Flammable atmosphere Inadequate wiring 25

26 © North Slope Training Cooperative—May 2012. All rights reserved. Electrical Shock Electrical shock occurs when a person’s body completes an electrical circuit by touching: an energized wire and an electrical ground. an energized wire and another wire of a different voltage. a metallic part that is “hot” because it’s touching an energized wire and is in contact with the ground. A energized wire while perspiring or standing on wet ground. 26

27 © North Slope Training Cooperative—May 2012. All rights reserved. Electrical Shock Electrical shock can cause: a slight tingling or total immobility severe burns internal bleeding, tissue, and muscle damage cardiac arrest and death (electrocution) Electrical shock is often the beginning of a chain of events which may include falls, cuts, broken bones. 27

28 © North Slope Training Cooperative—May 2012. All rights reserved. Electrical Shock The severity of injury from electrical shock depends on the: amount of current flowing through the body. amount of voltage. path of the current through the body. length of time the body is part of the circuit. resistance of the skin. 28

29 © North Slope Training Cooperative—May 2012. All rights reserved. Arc Flash or Blast Fire or explosion can occur if the atmosphere contains a flammable or explosive mixture. An arc flash or blast can result in burns, blindness, hearing loss, and shrapnel wounds. Arc flashes and/or blasts occur when high amperage currents jump from one conductor to another through air, generally during opening or closing circuits or when static electricity is present. 29

30 © North Slope Training Cooperative—May 2012. All rights reserved. Safe Work Practices 30

31 © North Slope Training Cooperative—May 2012. All rights reserved. Equipment Inspections Inspect all equipment, appliances, extension cords or plug-connected hand tools for any sign of damage or missing parts prior to use. Tag defective appliances, tools, and extension cords, and turn them in for repair. When electric-driven equipment becomes unsafe to operate, it shall be locked and tagged out immediately. ASH, page 22 BP ASH, page 59 31

32 © North Slope Training Cooperative—May 2012. All rights reserved. Equipment Repairs Only qualified and authorized personnel shall: repair, adjust, or install electrical equipment and wiring systems. make repairs to extension cords and cords on electrical tools. ASH, page 22 BP ASH, page 59 32

33 © North Slope Training Cooperative—May 2012. All rights reserved. Extension Cords Use only three-wire, grounded, extension cords. Electrical cables and/or extension cords should be run overhead and not laid on the ground or deck (ASH, page 24; BP ASH, page 60). High current equipment or appliances should be plugged directly into a wall outlet whenever possible. 33

34 © North Slope Training Cooperative—May 2012. All rights reserved. Extension Cords All extension cords should be plugged into: a GFCI outlet, a GFCI built into the cord, or a GFCI adapter used between the wall outlet and the cord plug. 34

35 © North Slope Training Cooperative—May 2012. All rights reserved. Power Tools All electrical equipment and tools must have an on and off switch and may not be turned on or off by plugging or unplugging the supply cord at the power outlet. All portable electric tools shall be used with ground fault circuit interrupters (GCFI) or be included in an assured grounding program. Avoid contact between two connections on a battery. ASH, page 22 BP ASH, page 59 35

36 © North Slope Training Cooperative—May 2012. All rights reserved. Power Tools and Equipment Motor overloads may be reset once after an Operator has checked the motor for any unusual conditions such as hot bearings or motor. Notify facility electrician of the trip. Motor starts per hour shall not exceed the manufacturer’s specifications. Any feeder or branch circuit breaker trips shall be brought to the attention of the Supervisor or facility electrician. ASH, page 23 BP ASH, page 60 36

37 © North Slope Training Cooperative—May 2012. All rights reserved. Lighting A Hot Work Permit is required to install or use non-explosion proof temporary lighting in a classified area. All portable lights shall be used with ground fault circuit interrupters (GCFI) or be included in an assured grounding program. Low voltage lights (50 volts or less) may be used in lieu of lights with GCFI. Use approved lighting in wet and classified areas ASH, page 22 BP ASH, page 59 37

38 © North Slope Training Cooperative—May 2012. All rights reserved. Working Near Energized Equipment Portable ladders, used for electrical work, shall have non-conductive side rails. Equipment operating within 15 feet of any un-insulated power distribution system line, structure, guywire or switch yard requires prior clearance by the appropriate Company Supervisor. ASH, pages 23-24 BP ASH, pages 60-61 38

39 © North Slope Training Cooperative—May 2012. All rights reserved. Working Near Energized Equipment Maintain minimum 4 foot NEC required clearances in front of all switchgear and motor control centers for access. If these clearances are not present, the switchgear must be appropriately marked with warning labels. These spaces are not intended for storage areas and must be kept clear. ASH, page 22 BP ASH, page 59 39

40 © North Slope Training Cooperative—May 2012. All rights reserved. Avoiding Other Electrical Hazards Avoid overloading circuits by plugging in multiple appliances (microwave ovens, toasters, space heaters, coffeepots) into the same outlet. Remove jewelry and other conductive objects before starting work. ASH, pages 6, 11 BP ASH, pages 30, 38 40

41 © North Slope Training Cooperative—May 2012. All rights reserved. Electrical Lockout Tagout If an employee can be exposed to contact with energized electrical equipment, the circuits energizing the parts shall be isolated by lockout tagout procedures (OSHA 1910.333(b)(2) ). Only authorized personnel may perform lockout and tagout work on electrical equipment. Affected employees will be notified when lockout and/or tagout activities are being performed in their work area. ASH, page 189 BP ASH, pages 237 41

42 © North Slope Training Cooperative—May 2012. All rights reserved. Personnel Restrictions Only authorized personnel shall be permitted in electrical distribution switchgear rooms and enclosures. Equipment operating within 15 feet of any un-insulated power distribution system line, structure, guy wire, or switch yards requires prior clearance by the appropriate Company Supervisor. ASH, pages 23-24 BP ASH, pages 59-60 42

43 © North Slope Training Cooperative—May 2012. All rights reserved. Personnel Restrictions Only a qualified electrician may bring a conductive object closer than 15 feet to unguarded, energized overhead lines. Power distribution switchgear shall be operated only by qualified personnel. Review the electrical safety procedures in the Alaska Safety Handbooks. ASH, pages 23-24 BP ASH, pages 59-60 43

44 © North Slope Training Cooperative—May 2012. All rights reserved. Responding to an Electrical Emergency 44

45 © North Slope Training Cooperative—May 2012. All rights reserved. Follow the Emergency Action Plan Remain calm and keep your distance. Turn off the power. Call for help immediately. Do not touch the victim. Trained personnel may administer First Aid or CPR when it is safe to touch the victim. 45

46 © North Slope Training Cooperative—May 2012. All rights reserved. Fire Extinguishers Approved fire extinguishers should be provided near electrical breaker panels and distribution centers. Water-type extinguishers are not intended for use on electrical fires and shall not be located closer than 50 feet from electrical equipment. Do not use a fire extinguisher unless you are trained to do so. ASH, pages 11-12 BP ASH, pages 35-36 46

47 © North Slope Training Cooperative—May 2012. All rights reserved. Summary Standards and Terms How Electricity Works Electrical Hazards and Injuries Safe Work Practices Responding to Electrical Emergencies 47


Download ppt "North Slope Training Cooperative © North Slope Training Cooperative—revised May 2012. All rights reserved. Electrical Safety for Non- Electrical Workers."

Similar presentations


Ads by Google