1. Samantha 3 Things to Know Dave Hackett FTC Mentor Valley Forge, PA

2. 2 Agenda Introduction 3 Things to Know –Mounting –Power –Getting Connected Just One More Thing… Summary

3. 3 Introduction Samantha Module –A Wi-Fi device that allows a team to control its robot remotely –Attaches to NXT using USB cable –Receives commands from game controllers connected to the Field Control System Samantha Field Control System (FCS) –Software and hardware setup that allows FTC robots to engage in competition –Consists of: Laptop w/Samantha FCS Software Wi-Fi router USB cables, hubs, and game controllers External monitor for timer display Resources –Read: FCS User's Guide for teamsFCS User's Guide for teams –Watch: FTC Video Tutorial - Setting Up the Field Control SystemFTC Video Tutorial - Setting Up the Field Control System

4. 4 1) Mounting The best place to mount the Samantha module is: a)Deep inside the robot, surrounded by as much metal as possible to protect it from damage. b)High up and securely mounted without metal blocking its antenna. c)Laying on top of the motor controller. d)On the front as a plow so you can push and score rings that have dropped on the floor.

5. 5 Mounting Best Practices Mount Samantha module as high as possible Do not bury Samantha module behind a mass of metal Use as short a USB cable as possible, usually 12” Ensure good strain relief for USB cable –The ½” gear hub the right size is a good choice to use as a spacer Samantha Mounting Best Practices Report –Mounting Samantha module laterally results in the best overall signal strength

6. 6 2) Power The better way to power the Samantha module is: a) b)

7. 7 Power Best Practices Wire directly to switch and battery –Samantha Mounting Best PracticesSamantha Mounting Best Practices Robot Power Management Using Anderson Powerpole® Connectors –http://www.usfirst.org/sites/default/files/uploadedFiles/Robotics_Programs/FT C/FTC_Documents/Anderson-Powerpole-Guide.pdfhttp://www.usfirst.org/sites/default/files/uploadedFiles/Robotics_Programs/FT C/FTC_Documents/Anderson-Powerpole-Guide.pdf –Thanks to Purple Gears / FTC Team 2901 Check for an expanded female connector

8. 8 3) Getting Connected How do I connect to the network?

9. 9 Configure Samantha Wi-Fi Required –USB flash drive 4 GB maximum (FAT file system) –Network information SSID - same as on FCS router Network Key - same as on FCS router Network Authentication: WPA2-PSK Encryption: AES Samantha Competition Network Config –“FTC_FIELD” Wireless Network Settings –Settings stored in FTCNTKY folder on flash drive Use flash drive to transfer settings to Samantha module –LED sequence Red, White, Blue, White, Red Resources –Watch: FTC Video Tutorial - How to update Samantha's FirmwareFTC Video Tutorial - How to update Samantha's Firmware

10. 10 Just One More Thing… Prepare NXTSamostat

11. 11 Prepare NXT Name your NXT –Use your FTC Team number –Append hyphen and letter on additional NXTs (e.g. 0010-A, 0010-B) Install programs required at Tournaments –Program Chooser –Samostat Define the default Tele-op program –Run Program Chooser –Define within programming environment Help the FCS Operator and the FTA help you! Use meaningful names for autonomous and Tele-op programs

12. 12 Samostat Wi-Fi status and network verification Required to be installed on NXT at Tournaments Samantha FCS folder –RobotC: samostat.c –LabVIEW: samostat.vi Samostat displays –Firmware version –IP address of Samantha –Connection counters –Detected Wi-Fi networks asterisk: connected to network blank: not connected to network

13. 13 Summary 1)Mounting: USB cable secured, mounted high without interference 2)Power: Samantha as close to the battery and switch as possible 3)Getting Connecting: Use Samantha Competition Network Config program and flash drive ** Use Samantha module and FCS in practices before Tournaments ** More Information: http://www.usfirst.org/roboticsprograms/ftc/samantha