1. 1 Midterm statistics – On campus students only ECEN 5817 Midterm Exam, Spring 2008 On-campus students Average = 86.3 % Averages by problem: 1.32.3 / 35 = 92.4 % 2.26.9 / 30 = 89.5 % 3.27.1 / 35 = 77.5 % Grade Curve A 90 – 100 A- 88 – 89 B+ 84 – 87 B 78 – 83 B- 75 – 77 C+ 70 – 74 C 65 - 69

2. 2 AC modeling of quasi-resonant converters Extension of State-Space Averaging to model non-PWM switches Use averaged switch modeling technique: apply averaged PWM model, with d replaced by µ Buck example with full-wave ZCS quasi-resonant cell: µ = F

3. 3 Relevant material Background on state-space averaging: Textbook Section 7.3 Background on circuit averaging and averaged switch modeling: Textbook Section 7.4 Averaging the terminal waveforms of a resonant switch network: Textbook Section 20.2.2 Handwritten notes on website, under “Materials on quasi-resonant converters” Extension of state-space averaging to model dynamics of resonant switch convertersExtension of state-space averaging to model dynamics of resonant switch converters A worked example: extended state-space averaging Averaged switch modeling Example: extended state-space averaging of a quasi-resonant SEPICExample: extended state-space averaging of a quasi-resonant SEPIC

4. 4 7.3. State Space Averaging A formal method for deriving the small-signal ac equations of a switching converter Equivalent to the modeling method of the previous sections Uses the state-space matrix description of linear circuits Often cited in the literature A general approach: if the state equations of the converter can be written for each subinterval, then the small-signal averaged model can always be derived Computer programs exist which utilize the state-space averaging method

5. 5 7.3.1. The state equations of a network A canonical form for writing the differential equations of a system If the system is linear, then the derivatives of the state variables are expressed as linear combinations of the system independent inputs and state variables themselves The physical state variables of a system are usually associated with the storage of energy For a typical converter circuit, the physical state variables are the inductor currents and capacitor voltages Other typical physical state variables: position and velocity of a motor shaft At a given point in time, the values of the state variables depend on the previous history of the system, rather than the present values of the system inputs To solve the differential equations of a system, the initial values of the state variables must be specified

6. 6 State equations of a linear system, in matrix form A canonical matrix form: State vector x(t) contains inductor currents, capacitor voltages, etc.: Input vector u(t) contains independent sources such as v g (t) Output vector y(t) contains other dependent quantities to be computed, such as i g (t) Matrix K contains values of capacitance, inductance, and mutual inductance, so that K dx/dt is a vector containing capacitor currents and inductor winding voltages. These quantities are expressed as linear combinations of the independent inputs and state variables. The matrices A, B, C, and E contain the constants of proportionality.

7. 7 Example State vector Matrix K Input vectorChoose output vector as To write the state equations of this circuit, we must express the inductor voltages and capacitor currents as linear combinations of the elements of the x(t) and u( t ) vectors.

8. 8 Circuit equations Find i C1 via node equation: Find i C2 via node equation: Find v L via loop equation:

9. 9 Equations in matrix form The same equations: Express in matrix form:

10. 10 Output (dependent signal) equations Express elements of the vector y as linear combinations of elements of x and u :

11. 11 Express in matrix form The same equations: Express in matrix form:

12. 12 7.3.2. The basic state-space averaged model Given: a PWM converter, operating in continuous conduction mode, with two subintervals during each switching period. During subinterval 1, when the switches are in position 1, the converter reduces to a linear circuit that can be described by the following state equations: During subinterval 2, when the switches are in position 2, the converter reduces to another linear circuit, that can be described by the following state equations:

13. 13

14. 14

15. 15 Equilibrium (dc) state-space averaged model Provided that the natural frequencies of the converter, as well as the frequencies of variations of the converter inputs, are much slower than the switching frequency, then the state-space averaged model that describes the converter in equilibrium is where the averaged matrices are and the equilibrium dc components are

16. 16 Solution of equilibrium averaged model Equilibrium state-space averaged model: Solution for X and Y :

17. 17 Small-signal ac state-space averaged model where So if we can write the converter state equations during subintervals 1 and 2, then we can always find the averaged dc and small-signal ac models

18. 18 Relevant background State-Space Averaging: see textbook section 7.3 Averaged Circuit Modeling and Circuit Averaging: see textbook section 7.4

19. 19

20. 20

21. 21 Averaged Switch Modeling Separate switch elements from remainder of converter Remainder of converter consists of linear circuit The converter applies signals x T to the switch network The switch network generates output signals x s We have solved for how x s depends on x T

22. 22 Block diagram of converter Switch network as a two-port circuit:

23. 23 The linear time-invariant network

24. 24 The circuit averaging step To model the low-frequency components of the converter waveforms, average the switch output waveforms (in x s (t)) over one switching period.

25. 25 Relating the result to previously-derived PWM converter models: a buck is a buck, regardless of the switch We can do this if we can express the average x s (t) in the form

26. 26 PWM switch: finding X s1 and X s2

27. 27 Finding µ: ZCS example where, from previous slide,

28. 28 Derivation of the averaged system equations of the resonant switch converter Equations of the linear network (previous Eq. 1): Substitute the averaged switch network equation: Result: Next: try to manipulate into same form as PWM state-space averaged result

29. 29 Conventional state-space equations: PWM converter with switches in position 1 In the derivation of state-space averaging for subinterval 1: the converter equations can be written as a set of linear differential equations in the following standard form (Eq. 7.90): But our Eq. 1 predicts that the circuit equations for this interval are: These equations must be equal: Solve for the relevant terms:

30. 30 Conventional state-space equations: PWM converter with switches in position 2 Same arguments yield the following result: and

31. 31 Manipulation to standard state-space form Eliminate X s1 and X s2 from previous equations. Result is: Collect terms, and use the identity µ + µ’ = 1: —same as PWM result, but with d  µ

32. 32 Perturbation and Linearization The switch conversion ratio µ is generally a fairly complex function. Must use multivariable Taylor series, evaluating slopes at the operating point:

33. 33 Small signal model Substitute and eliminate nonlinear terms, to obtain: Same form of equations as PWM small signal model. Hence same model applies, including the canonical model of Section 7.5. The dependence of µ on converter signals constitutes built-in feedback.

34. 34 Salient features of small-signal transfer functions, for basic converters

35. 35 Parameters for various resonant switch networks

36. 36 Example 1: full-wave ZCS Small-signal ac model µ = F Averaged switch equations:Linearize: Resulting ac model:

37. 37 Low-frequency model Tank dynamics occur only at frequency near or greater than switching frequency —discard tank elements —same as PWM buck, with d replaced by F

38. 38 Example 2: Half-wave ZCS quasi-resonant buck Now, µ depends on j s :

39. 39 Small-signal modeling with Perturbation and linearization of µ(v 1r, i 2r, f s ) : Linearized terminal equations of switch network:

40. 40 Equivalent circuit model

41. 41 Low frequency model: set tank elements to zero

42. 42 Predicted small-signal transfer functions Half-wave ZCS buck Full-wave: poles and zeroes are same as PWM Half-wave: effective feedback reduces Q-factor and dc gains