1. Rock Structure and Fault Activity chapter 9

2. What is structural geology The study of the forms of the Earth’s crust and the processes which have shaped it analysis of displacement and changes in shape of rock bodies (strain) reconstruct stress that produced strain

3. Structural Deformation Rocks deform when stresses placed upon them exceed the rock strength Brittle deformation (e.g. fractures) ductile deformation (e.g. folds)

4. Driving Forces Plate tectonics – plate convergence and ridge spreading Deep burial of sediments Forceful intrusion of magma into the crust Meteorite impacts

5. Evidence of Crustal Deformation Folding of strata Faulting of strata Tilting of strata Joints and fractures

6. Evidence of Crustal Deformation Folding of strata Faulting of strata Tilting of strata Joints and fractures

7. Evidence of Crustal Deformation Folding of strata Faulting of strata Tilting of strata Joints and fractures

8. Evidence of Crustal Deformation Folding of strata Faulting of strata Tilting of strata Joints and fractures

9. Applications of structural geology subsurface exploration for oil and gas mining exploration geotechnical investigations groundwater and environmental site assessment

10. Geological structures Geologic bed contacts Primary sedimentary structures Primary igneous structures Secondary structures

11. Fundamental Structures Three fundamental types of geologic structures: bed contacts primary structures - produced during deposition or emplacement of rock body secondary structures - produced by deformation and other process after rock is emplaced

12. Bed Contacts Boundaries which separate one rock unit from another two types: 1. Normal conformable contacts 2. Unconformable contacts (‘unconformities’)

13. Conformable Bed Contacts Horizontal contact between rock units with no break in deposition or erosional gaps no significant gaps in geologic time Book Cliffs, central Utah

14. Unconformable Contacts Erosion surfaces representing a significant break in deposition (and geologic time) angular unconformity disconformity non-conformity

15. Angular Unconformity Bedding contact which discordantly cuts across older strata discordance means strata are at an angle to each other commonly contact is erosion surface

16. Formation of an angular unconformity

17. Disconformity Erosional gap between rock units without angular discordance example: fluvial channel cutting into underlying sequence of horizontally bedded deposits

18. Nonconformity Sedimentary strata overlying igneous or metamorphic rocks across a sharp contact example: Precambrian-Paleozoic contact in Ontario represents a erosional hiatus of about 500 ma Grand Canyon, USA

19. Structural Relations The structural relations between bed contacts are important in determining: 1. presence of tectonic deformation/uplift and; 2. relative ages of rock units principle of original horizontality principle of cross-cutting principle of inclusion

20. Principle of Original Horizontality Sedimentary rocks are deposited as essentially horizontal layers exception is cross-bedding (e.g. delta foresets) dipping sedimentary strata implies tectonic uplift and tilting or folding of strata

21. Principle of Cross-cutting Igneous intrusions and faults are younger than the rocks that they cross-cut Mafic dike cutting across older sandstones

22. Cross-cutting Relations Often several cross-cutting relationships are present how many events in this outcrop?

23. Principle of Inclusion Fragments of a rock included within a host rock are always older than the host

24. Fundamental Structures Three fundamental types of structures: bed contacts primary structures secondary structures

25. Primary Sedimentary Structures Structures acquired during deposition of sedimentary rock unit Stratification - horizontal bedding is most common structure in sedimentary rocks

26. Primary Sedimentary Structures Cross-bedding - inclined stratification recording migration of sand ripples or dunes

27. Primary Sedimentary Structures Ripples - undulating bedforms produced by unidirectional or oscillating (wave) currents

28. Ripple marks

29. Primary Sedimentary Structures Graded bedding - progressive decrease in grain size upward in bed indicator of upwards direction in deposit common feature of turbidites

30. Primary Sedimentary Structures Mud cracks - cracks produced by dessication of clays/silts during subaerial exposure

31. Primary Sedimentary Structures Sole marks - erosional grooves and marks formed by scouring of bed by unidirectional flows good indicators of current flow direction

32. Primary Sedimentary Structures Fossils – preserved remains of organisms, casts or moulds good strain indicators determine strain from change in shape of fossil relative change in length of lines/angle between lines

33. Primary Igneous Structures Flow stratification layering in volcanic rocks produced by emplacement of successive lava sheets stratification of ash (tephra) layers

34. Primary Igneous Structures Flow stratification layering in volcanic rocks produced by emplacement of successive lava sheets stratification of ash (tephra) layers

35. Primary Igneous Structures Pillow lavas - record extrusion and quenching of lava on sea floor

36. Importance of Primary Structures 1. Paleocurrents - determine paleoflow directions 2. Origin – mode of deposition, environments 3. Way-up - useful indicators of the direction of younger beds in stratigraphic sequence 4. Dating - allow relative ages of rocks to be determined based on position, cross-cutting relations and inclusions 5. Strain indicators - deformation of primary structures allows estimates of rock strain

37. Secondary Structures Secondary structures - deformation structures produced by tectonic forces and other stresses in crust Principle types: fractures/joints faults/shear zones folds cleavage/foliation/lineation

38. Fractures and Joints Fractures – surfaces along which rocks have broken and lost cohesion Joints - fractures with little or no displacement parallel to failure surface indicate brittle deformation of rock

39. Fractures and Joints

40. Faults Faults - fracture surfaces with appreciable displacement of strata single fault plane fault zone - set of associated shear fractures shear zone - zone of ductile shearing

41. Shear Zones Shear zone - zone of deformed rocks that are more highly strained than surrounding rocks common in mid- to lower levels of crust shear deformation can be brittle or ductile

42. Fault Terminology Hanging wall block- fault block toward which the fault dips Footwall block - fault block on underside of fault Fault plane – fault surface

43. Fault Slip Slip is the fault displacement described by: direction of slip sense of slip magnitude of slip

44. Fault Types Dip-slip faults - slip is parallel to the fault dip direction normal reverse thrust

45. Fault Types Normal fault - footwall block dispaced up

46. Fault Types Reverse (thrust) fault - footwall block displaced down

47. Fault Types Strike-slip – fault slip is horizontal, parallel with strike of the fault plane right-handed (dextral) left-handed (sinistral)

48. Fault Types Oblique slip – Combination of dip- and strike-slip motion dextral-normal dextral-reverse sinistral-normal sinistral-reverse

49. Faults What type of faults are shown here?

50. Faults What type of faults are shown here?

51. Faults What type of faults are shown here?

52. Faults What type of faults are shown here?

53. Folds Folds – warping of strata produced by compressive deformation range in scale from microscopic features to regional-scale domes and basins indicators of compression and shortening

54. Fold Terminology Hinge (Axial) plane - imaginary plane bisecting fold limbs Hinge line - trace of axial plane on fold crest Plunge - angle of dip of hinge line

55. horizontal fold axis

56. plunging fold axis

57. Fold Terminology Anticline - convex in direction of youngest beds Syncline - convex in direction of oldest beds Antiform - convex upward fold (stratigraphy unknown) Synform - concave upward fold

58. Anticline / Antiform?

59. Syncline Synform?

60. Fold Terminology Synformal Anticline - overturned anticline Antiformal Syncline - overturned syncline

61. Fold Terminology Monocline - step-like bend in strata

62. Foliation and Cleavage Foliation - parallel alignment of planar fabric elements within a rock Cleavage - tendency of rock to break along planar surface cleavage is a type of foliation resemble fractures but are not physical discontinuities

63. Foliation and Cleavage Foliation - parallel alignment of planar fabric elements within a rock Cleavage - tendency of rock to break along planar surface cleavage is a type of foliation resemble fractures but are not physical discontinuities

64. Lineations Lineation - sub-parallel to parallel alignment of elongate linear fabric elements in a rock body e.g. slickenlines and grooves on fault plane surface

65. Structural analysis Involves three steps 1.Descriptive or geometric analysis 2.Kinematic analysis 3.Dynamic analysis

66. Geometrical analysis Measurement of the 3-dimentional orientation and geometry of geological structures simplified into: lines planes

67. lines or linear geological structures liniation –any linear feature observed in a rock or on a rock surface –any imaginary line – such as a fold axis

68. Orientation of linear structures LINES Trend – azimuth direction measured clockwise from north 360° Plunge – angle of inclination of line measured from the horizontal (0 - 90°)

69. Examples of linear structures Primary – flute casts, grooves, glacial striae Secondary – slickenlines, mineral lineations Glacial striations on bedrock sole marks

70. Examples of linear structures Primary – flute casts, grooves, glacial striae Secondary – slickenlines, mineral lineations Grooves on fault plane Slickenlines on fault surface

71. Orientation of Linear Structures linear structures on an other planar surface: pitch angle –angle from horizontal measured within the plane Pitch angle Striations on a fault plane

72. Planar Geological Structures bedding planes and contacts foliation joint surfaces fault planes fold limbs fold axial planes (imaginary surface)

73. Examples of Planar Structures Bedding planes – most common primary depositional surface erosional surface inclined bedding plane

74. Examples of Planar Structures Foliation – cleavage planes produced by metamorphism common in slates and phyllites foliated phyllite

75. Examples of Planar Structures Joint planes – planar fracture surfaces caused by brittle failure

76. Examples of Planar Structures Fold axial plane - imaginary plane bisecting limbs of fold

77. Orientation of Planar Structures The attitude of a plane can be established from any two lines contained in the plane, provided they are not parallel

78. Orientation of Planar Structures Strike – azimuth direction of a horizontal line in a plane Dip – angle of inclination of line measured from the horizontal (0 - 90°)

79. Orientation of Planar Structures Appearent dip –dip measured along a line other than 90 to strike –apparent dip will always be less than the true dip angle

80. Measurement of orientation Strike (plane) Trend (line) azimuth orientation measured with a compass

81. Measurement of orientation Strike (plane) Trend (line) azimuth orientation measured with a compass Dip (plane) Plunge (line) inclination measured using an inclinometer

82. Measurement of Strike Direction Right hand rule??? When your thumb (on your right hand) is pointing in the direction of strike your fingers are pointing in the direction of dip!!

83. Measure of Dip Angle The angle between the horizontal and the line or plane

84. Structural Data Symbols represent different structural data Symbols are placed on the map: –in the exact field orientation –where the data is measured

85. Standard Structural Symboles

86. Exercises geological maps structure contour and structure maps three-point problems cross sections sterionets

87. Geological Maps distribution of rock types and contacts –symbols on map represent structures (strike and dip, fold axes, faults etc.) –map and structure symbols allow you to infer subsurface structures

88. Outcrop patterns Outcrop patterns controlled by attitude (strike and dip) of beds and topographic relief

89. “V” Rule Beds dipping downstream “V” – downstream Beds dipping upstream “V” – upstream

90. Vertical beds cut straight Vertical oriented beds cut in a straight line regardless of topography!!

91. Horizontal beds layers always at the same altitude – do NOT dip in any direction –layered cake

92. Outcrop Patterns Which direction are the beds dipping?

93. Outcrop Patterns Which direction are the beds dipping?

94. Outcrop Patterns Which direction are the beds dipping?

95. Outcrop Patterns Which direction are the beds dipping?

96. Block models Relations between outcrop patterns and subsurface structures map view on bottom – cross sections in blocks on top

97. Bryce 3-D modeling blocks

98. Structural Contour Maps Map showing the relief of a subsurface geological surface –top or bottom of bedding planes, faults or folded surface –constructed from borehole data

99. Structure Contour Maps Structure contour lines are lines of equal elevation show elevation relative to horizontal datum values are often negative since subsurface elevations are commonly below sea level

100. Datum Surface Datum is a horizontal reference surface regional stratigraphic surface

101. Constructing Structural Contours Points of equal elevation along a bed contact intersection of contact with topo contour draw structure contours through points of equal elevation

102. Planar surfaces Uniformly dipping plane – contours are parallel

103. folded planar surfaces Contours have variable spacing

104. Rules of Contouring 1) contours cannot cross or bi-furcate 2) contours cannot end in the middle of the map, except at a fault or other discontinuity 3) same contour interval must be used across the map and elevations must be labelled 4) elevation is specified relative to datum (e.g. m above sea level)

105. Determining Dip Dip direction and angle can be determined from structure conour maps measure horizontal separation X and find difference in Z tan  = Z/X,  = tan –1 (Z/X) e.g.  = tan –1 (10m/100m),  = 6°

106. Three-point problem A minimum of three points are required to uniquely define the orientation of a plane

107. Three-point problem Find min and max values Draw line between these and divide distance into intervals Connect points of equal elevation Two points in a plane at the same elevation lie in the line of strike

108. Three-point problem Find min and max values Draw line between these and divide distance into intervals Connect points of equal elevation Two points in a plane at the same elevation lie in the line of strike

109. Isochore Map Drill hole logs giving the thicknesses in the drilled (often vertical) direction Apparent thickness – true thickness = perpendicular to bedding

110. Isopach Map Map showing “true” thickness measured perpendicular to bedding

111. Cross-sections Cross-section is a 2-D slice through stratigraphy construct perpendicular to dip = true dip constructed at any other direction = apparent dip

112. Engineering properties of faulted or folded rock shear strength –loose materials –compressive materials –permeable materials

113. hydrology of fault zones water in fault zones common due to fractured rock –fault zone may be either an aquifer or an aquiclude crushed to gravel crushed to clay

114. hydrology of fault zones water in fault zones common due to fractured rock –fault zone may be either an aquifer or an aquiclude crushed to gravel crushed to clay

115. Problems due to water in fault zones leakage of waste water under a landfill leakage of water under a dam sudden collapse and inflow of water into a tunnel hydrothermal alteration of rocks to clay minerals along faults – variable physical, mechanical and hydrological properties soluble rocks - cavities

116. Activity of faults? Risk for further movement –active fault – has moved in the last 100 000 to 35 000 years –dormant fault – no recorded movement in recent history

117. Indicators of fault movement fault scarps stream displacement sag ponds lineaments vegetation displacement

118. Risk potential depends upon: 1.duration of the quake 2.intensity of the quake 3.recurrence of the quake

119. Potential trigger’s stess > stength water in a reservoir – added weight and lubrication storage of fluids in old mines blasting surface excavation ground water mined from aquifers extraction of oil and gas from aquifers

120. Case studies Auburn Dam – wide slender arch dam on the American River, upstream of Sacramento, California Fig. 9.31 pre investigations –detailed mapping –8 km trenches –2 km exploratory tunnels –30 km borings

121. Auburn Dam geology –metamorphic competent amphybolite –metasediments –included vertical weak zones and lenses of chlorite schist, talc schist and talcose serpentinites up to 30 m wide, aligned with foliation –series of sub parallel mineralized reverse faults with strike transverse to the dam axis dipping 40 to 55 degrees into the abutment –two of the longest faults are tangential to the dam, close or under the dm on the left abutment –no active faults in the area –the area was supposed to be low seismicity

122. Auburn Dam foundation construction –earthquake occurred 5.7 –regional fault study –reassessment 32 km trenches more borings surface excavations aim to establish the time relationship of the faults

123. Auburn Dam Concluded that the faults wee formed in another tectonic setting than the present (compressional rather that extensional stress field) A review of the dam – will it withstand vibrations from a 6.5 magnitude quake on a fault < 8 km from the dam?? “Off set” design recommended to withstand 25 mm to 900 mm NO DAM built due to discussions on safety!

124. Baldwin Hill reservoir – failed 1963 1 principle embankment, 47 m high, and 5 smaller embankments excavated hollow in between at the top of a mountain range

125. Baldwin Hill reservoir – failed 1963 geology –friable deposits of the Pliocene Pico Formation, massive beds of clayey, sandy siltstone –Pleistocene Ingewood Formation. interbedded layers of sand, silt, and clay, with some thin linestone beds; some of the sand and silt beds are unconsolidated and erodable –Both formations contain calcareous and limonitic concretions –bedding dips slightly 5 to 7 degrees, striking roughly parallel to the Inglewood fault –major active fault, Inglewood, passes just 150 m west of the reservoir –the fault is a right lateral strike slip with a vertical component –fault acts as a subsurface dam for a major oil field in the hills

126. Baldwin Excavation phase –7 minor faults wee mapped –mostly normal faults –3 to 100 mm silty gouge –largest fault had a total displacement of more than 8 m

127. Baldwin Design –rock foundation lined with asphalt and gravel drain layer covered with compacted clay covered with asphalt

128. Baldwin Construction phase 1947-51 –fault 1 caused problems –slide initiated revealing that the fault passed beneath the inlet/outlet tower –the tower was relocated 48 ft

129. Baldwin after completion –liner cracked along the trace of the fault –emptied in 1957 –cracks repaired –cracks were also observed in the surrounding area of the reservoir –the cracks dipped steeply –trend NS parallel to the faults –some exhibited small sinkholes – indicative of extensional strain –offset dip slip

130. Baldwin nearby oil fields – oil was being extracted –resulted in subsidence due to collapse of the aquifer –subsidence of 2.7 m between 1917 and 1962

131. Baldwin Failure 1971 –emptied completely in 4 hours –seepage along the fault had enlarged to a pipe –then to a tunnel and –then the collapse of the roof –a canyon eroded completely through the all of the reservoir

132. Baldwin Failure 1971 –Why?? cracks in the floor extended across the entire reservoir along the trace of the fault 50 mm displacement open voids along the fault movement along the fault had fractured the lining rupture of the asphalt membrane water eroded cavities into the foundation rock