1. 00 Scale Colour Light Signals Instructions for building working colour light signals as featured on ”Windward” model railway. Designed for use with 12V DC power supply, with common anode (+) at signals. Common anode chosen for compatibility with electronic switching. Use of 12V LED’s eliminates the need for separate resistors and reduces risk of burnout. Structures are made from brass, with copper wire for ladders & handrails. Signal head design is the same for all types of gantry. Dimensions in mm unless stated otherwise. Inches are used where the brass stock is supplied in imperial sizes. © F1p UK 2010

2. Materials List Tubing 5/32” brass tube KS128 3.5mm brass tube thinwall KSM85 Brass strip 3/16” brass channel KS183 0.032” x ½” brass strip KS241 1/32” x 3/32” brass strip Wire 0.5mm dia wire Telephone cable (4 x 0.5mm) 1.0mm 2 / 1.2mm dia wire. 30 awg kynar coated wire LED’s 3mm 12V LED’s Other Epoxy putty Paints © F1p UK 2010

3. Standard Lineside Signals 2mm tab formed by cutting tube to ¾ of full depth and flattened for soldering to faceplate Base of pole bevelled at 45° for easy insertion through baseboard Baseplate formed from ½” x.032” brass strip with 5/32” hole 75 Pole is made from 5/32” tube ½” Ladder rungs made from 0.5mm wire Ladder rails from 1mm wire Solder applied to join rungs to rails Lamp covers cut from 3.5mm dia thinwall brass tube 5 2 Faceplate drilled With 3.0 dia holes Made from flattened channel KS 183 3.5 4.0 3.0 10 Step 1 Step 2Step 3 ¾” 6 © F1p UK 2010

4. Solder parts in the following order: 1.Ladder rungs to rails 2.Signal faceplate to pole 3.Pole into base 4.Attach ladder to base and pole LED anode lead bent ready for soldering to faceplate LED anodes soldered to faceplate Leads cut to length Solder wires in the following order: 1.Common anode attached just inside the pole 2.Thread wires through the pole and solder to LED cathodes Wires to be 30 - 60 cm long For easy connection under baseboard Use 0.5mm single strand telephone cable Step 4 Step 5 Step 7 Step 6 55 © F1p UK 2010

5. Encase the Back of the LED’s with epoxy putty, shaped and smoothed. Paint in the final colour scheme Step 8 Step 9 Paint the insides of the lamp covers matt black Attach to the LED’s Using a small Amount of epoxy glue Step 10 © F1p UK 2010

6. Lineside with Access Platform 3.5 4.0 3.0 10 Faceplate 6mm longer Bent at 90° to solder to underside of platform 4 16 Platform made from ½” x 0.032” strip Holes for handrail uprights drilled To suit wire diameter. (1.0mm 2 wire with 1.2mm hole) 22 Wires from signal head run across platform and inside pole Variations of standard design © F1p UK 2010

7. Overhead Gantry 100 28 67 75 30AWG Kynar coated single strand wire Deck supported on brass channel 2mm holes drilled through deck Into channel for wires Angled pieces from 1/32” x 3/32” strip Tabs to keep wires inside channel Tube projects below baseplate through baseboard Variations of standard design © F1p UK 2010

8. Junction Signal 22 60 70 30AWG Kynar coated single strand wire Deck supported on brass channel Wires run along platform Into pole Variations of standard design © F1p UK 2010

9. Attached to Overbridge Deck supported on brass channel Screwed to bridge 2mm holes drilled through deck for wires Hoops to support wiring Variations of standard design © F1p UK 2010