We think you have liked this presentation. If you wish to download it, please recommend it to your friends in any social system. Share buttons are a little bit lower. Thank you!
Presentation is loading. Please wait.
Published byMiracle Peeling
Modified about 1 year ago
RISER SETUP NOTE: All levels of the riser are connected using the same method:
Locate the latch and security pin attached to the front legs of the higher riser:
Remove the pin and open latch:
Lift up the lower riser and place the channel in the groove in the lower section of the latch:
Swing the upper portion of the latch over the riser, securing it in the groove. Replace pin to secure latch from opening:
Lift the movable couplings that are attached to the front legs of the higher riser and place it over the tube protruding from the back legs of the lower riser:
How To De-Wing A Weedhopper By: Mike Schweim. Remove wing ribs, starting from the wingtips;
-From back of computer, remove screws holding right side of case -Keep track of the screws you remove! -Take off case wall by pulling back, then away from.
Digital StarLab Set-Up, Operation, Maintenance, and Teacher Manual for the Digital StarLab are in the links below or on the training tab in the BlackBoard.
We Design It Replacing Hard Drives Tutorial Seven Easy Steps By: James Landon Carie Jackson Odetta Rodriguez Michelle R. Person Miceala Vega.
FHM TRAINING TOOLS This training presentation is part of FHM’s commitment to creating and keeping safe workplaces. Be sure to check out all the training.
1 OVERHEAD CRANE SAFETY F&T Inc.. 2 OVERHEAD AND GANTRY CRANE OPERATION Hoist operators must inspect equipment daily before use. Do not operate a crane.
MICE Coupling Coil Fabrication Steps to Complete Allan DeMello Lawrence Berkeley National Laboratory Coupling Coil Working Group January 28, 2014 January.
Lesson No 05 Week No. 05 Lesson Name Vice. VICE Use:- For holding work pieces during filing, sawing, threading, drilling and other such operations.
CMS ZDC Crane Emergency Payload Removal Procedures This document proposes the viability of using a portable hydraulic actuator Hand crane (Davit crane)
46 cm 1.8 cm cm 35.5cm 21.5cm 10 cm 4.5 cm 18.5 cm 32.5cm 26 cm.
PS2200B/3000B Battery Replacement Procedure. 1.Disconnect the wire connecting the UPS and the battery pack. 2.Pull off the battery pack front panel.
375, 375XL 1¼” -2”. Modification Overview Production of the 1¼” -2” 375 began in 2004 and is current. The lead free version 375XL was introduced in.
The Sewing Machine. Head parts of the sewing machine.
How to Disassemble and M16 By: Anthony Johnson. Parts List Left and right hand guards Upper and Lower Receiver Charging Handle Bolt Carrier Retaining.
Pulleys. A pulley is a simple machine that uses grooved wheels and a rope to raise, lower or move a load.
New Products 5204 Openable API Bottom Loading Adapter Integrated flow indicator Longer sight glass Teflon lip seal in stuffing box Ergonomic aluminum.
Lotus Esprit S3 Front Suspension Dismantling. Picture shows nearside suspension prior to dismantling. The car is resting on axle stands positioned under.
MER/SUP 1 DOOR EVAPERATOR DRAIN PAN REPLACEMENT 1. Remove the (4) screws that secure the evaporator coil, using a 5/16” socket.
DBSL COMBAT EQUIPMENT. Overview Nomenclature of the Parachutist Drop Bag (PDB) Rigging the Combat Equipment for Jump operations Canopy procedures.
High-Lift Jack SECTION: Tools and Equipment ISSUED: REVISED: ##-####
CHAPTER 14 – WORK AND SIMPLE MACHINES. a machine that does work with only one movement Inclined plane Lever Wheel and Axle Screw Wedge Pulley.
MTRC Safety Alert issued on 31-May-2013 draw our highly attention for the innovative improvements. It is possible that a wire rope is able to come off.
Chapter 27: Workholding Devices for Machine Tools DeGarmo’s Materials and Processes in Manufacturing.
CRANE INCIDENT The following pictures are of a crane incident that occurred in the Netherlands at Shell's Antwerp Refinery. During a major turnaround,
LF866 2½”-10”. Product Overview Production of the 2½” – 10” sizes began in The LF866 utilizes a Type 2 bypass (Model LF619 single check).
Levolors New Size-In-Store Blind Cutting Machine.
1 FREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS PART NUMBER
Sophisticated Design Automatic Tailgate Final Presentation December 5, 2001 Ted Akiskalos June Doan Tarek Elshazly Maggie Kim David Nimitz Sharon Ramey.
Pulleys Assignment #35. A PULLEY is a simple machine that uses grooved wheels and a rope to raise, lower or move a load. There are 2 types of pulleys:
Jacto Incorporated, 9650 SW Herman Road, Tualatin, Oregon (800)
The Great Team1 Week 5 : Patent Search And Selection Analysis Bunk Bed Converter Adam Brown Blaine Gardner Sarah Gleaton Jimmy Jiang Addisu Lemlem Lee.
In the event, that we are unable to land off, the14”casing string on its Mandrel Casing hanger, the following steps will need to be performed. Present.
What is a simple machine? Machines are used to make the work easier or reduce the amount of force required to do work. The amount of WORK stays the same.
Honda 450 Installation Manual. STEP 1: Remove the (4) SHCS from the ATV swing arm Install the upper track kit swing arm bracket as shown Do not tighten.
Forklift Safety Cage Training Presented by Tom Dausch.
The most sophisticated sports knee ever! Optimised linkage knee with hydraulic cadence control.
Mechanism of the Injury (cause) Fall or hit on to knee cap.
Joint Institute for Nuclear Research Deformations and stresses in the flux return yoke A.Efremov, Yu.Lobanov, A.Makarov Darmstadt,
6/7/2006The Great Team1 Week 4 : Conceptual Designs Bunk Bed Converter Adam Brown Blaine Gardner Sarah Gleaton Jimmy Jiang Addisu Lemlem Lee Tschaepe.
NSTX NSTX Center Stack Upgrade Ensure fatigue resistant Welds: minimum # of locations shown, could be more. Various Weld Reinforcements & Hardware Replacement.
Pulleys Vocab. Vocab A Pulley is a wheel with a grooved rim in which a rope can run to change the direction of the pull (force) that lifts a load.
The BaBar Upgrade Load transfer of the Barrel and Endcap Calorimeters Richard F Boyce 21 October 2003.
Assembly Instructions Additional documents needed for Assembly: GA Drawings on all Units Header Platform GA Drawings Motor Deck Platform GA Drawing Packing.
1 Fire Fighter Qualifications and Safety Skill Drills 2.
SLHC Engineering Upgrade FCAL Remove-Install step by step procedure. Mircea Cadabeschi-University of Toronto March 01,
Equipment: Model 703 Bobcat Skid-Steer Loader with Backhoe. Job: Excavate a shallow trench around a roof drainage pond ( approximately.3 meter /1 foot;.6.
First Mercury Test by Stuart Walker. Original Setup.
November Lab Safety Always wear safety goggles, apron and gloves Always wash hands and lab area when finished dissection. Irresponsible behaviour.
© 2017 SlidePlayer.com Inc. All rights reserved.